Taymor Installation Instructions

32-F238 / 32-F238SSS Single Sided Indicator Deadbolt

These instructions guide the installation of the Taymor 32-F238 and 32-F238SSS Single Sided Indicator Deadbolt for doors 1-3/8" to 1-3/4" (35-45 mm) thick.

Tools Required for New Installation:

Phillips head screwdriver ?
2-1/8" (54 mm) hole saw ?️
1" (25.4 mm) drill bit ?️
Chisel ?

Tools Required for Replacement Installation:

Phillips head screwdriver ?

Installation Steps

Step 1: Mark Door

Measure the center line of the lock and the desired height from the finished floor. Select the backset (2-3/4" or optional 2-3/8"). Fold the template and apply it to the interior side of the door. Mark the center of the door as indicated on the template. Then, mark the center hole on the door face through the guide on the template.

Diagram shows a door edge and face with lines indicating the center line, the mark for the 1" hole in the door edge, and the mark for the 2-1/8" hole on the door face. Components like DEADBOLT, THUMB TURN ASSEMBLY, INDICATOR ASSEMBLY, STRIKE, WOOD FRAME REINFORCER, DUST BOX, and MOUNTING SCREWS are illustrated.

Step 2: Drill Holes

Drill a 2-1/8" (54 mm) hole through the door face as marked for the lockset. For wood doors, it is recommended to drill from both sides to prevent splitting. Drill a 1" (25.4 mm) hole in the center of the door edge for the latch.

Diagram shows the door face with a marked 2-1/8" (54 mm) hole and the door edge with a marked 1" (25.4 mm) hole.

Step 3: Install Latch

A. Insert the latch into the hole, keeping it parallel to the face of the door. Mark the outline of the latch face plate and remove the latch. B. Chisel a recess 5/32" (4 mm) deep, or until the latch plate is flush with the door edge. C. Insert the latch and tighten it to the door using #8 screws.

Diagram A shows inserting the latch and marking its outline. Diagram B shows chiseling the recess. Diagram C shows inserting the latch and securing it with screws.

Step 4: Install Strike

Close the door. Locate the strike in the jamb and align with the center line of the strike. Extend this line to the door stop. Measure half of the door thickness plus 1/8" from the door stop and vertically mark the centerline for the strike. Drill two 1" (25.4 mm) holes 1-1/4" (31.7 mm) deep in the door jamb, 5/16" (8 mm) above and 5/16" (8 mm) below the horizontal center line. CAUTION: The hole must be drilled a full 1-1/4" (31.7 mm) deep to ensure proper functioning. Match the screw holes on the strike with the vertical center lines on the jamb. Mark the outline of the strike and chisel a recess 1/4" (6.4 mm) deep for a flush fit of the dust box, wood frame reinforcer, and strike. Place the dust box and wood frame reinforcer into the mortise area and tighten to the frame using 3" wood screws. Insert the strike and tighten to the frame with #8 screws.

Diagram A shows a door jamb with center lines and marks for the strike. Diagram B shows drilling holes in the jamb. Diagram C shows fitting and securing the strike plate, dust box, and wood frame reinforcer.

Step 5: Install Thumbturn Assembly and Blank Plate

Insert the torque blade horizontally into the deadbolt latch. Crank until the indicator assembly is flush with the door face. Mate the thumbturn assembly with the torque blade on the indicator assembly. Insert the screws through the holes of the thumbturn assembly and latch body. Tighten the screws to the threaded posts of the blank mounting plate. Tighten the assembly so the complete assembly is tight to the door.

Diagrams illustrate inserting the torque blade into the latch, aligning the thumbturn assembly, and securing it with screws. Components like THUMB TURN ASSEMBLY, TORQUE BLADE, and INDICATOR ASSEMBLY are labeled.

Step 6: Backset Adjustment

To change the deadbolt to a 2-3/8" backset, rotate the faceplate 1/2 turn.

Diagram shows the deadbolt mechanism with a curved arrow indicating rotation of the faceplate to adjust the backset.

Template Information

IMPORTANT: Print template to scale if not factory supplied instructions.

The template provides guides for marking door edge and door side. It includes measurements for backsets: 2-3/8" (60 mm) and 2-3/4" (70 mm). It also shows door thickness measurements: 45 mm (1-3/4"), 40 mm (1-9/16"), and 35 mm (1-3/8"). Ensure the 1" (25.4 mm) hole is made at the center of the door edge.

Diagram shows a ruler, a fold line for the door edge, and markings for hole diameters and backset lengths.

Customer Service

For customer service, please contact:

WEST: 1-800-267-4774
EAST: 1-800-387-7064
Website: taymor.com

® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.

	Taymor Flush Deadbolt: Features, Specifications, and Finishes Detailed specifications and features of the Taymor Flush Deadbolt, including installation details, available finishes, and ordering information.
	Taymor 3900 Series Sectional Mortise Lock Door & Strike Preparation Guide Detailed technical specifications and preparation templates for Taymor 3900 series sectional mortise locks on metal and wood doors, including door and strike preparation dimensions.
	Taymor Professional Series Single Cylinder Deadbolt Specifications Comprehensive specifications for Taymor's Professional Series Single Cylinder Deadbolts, detailing features, construction, ANSI grade, keying services, fire rating, and available finishes with product codes.
	Taymor Professional Series Deadbolt Specifications \| ANSI Grade 3 Security Locks Detailed specifications for Taymor Professional Series deadbolts, including features, finishes, model numbers, ANSI Grade 3 rating, and warranty information. Find the right lock for your needs.
	Taymor Perspective Builders Series Residential Leverset Specifications \| Door Hardware Detailed specifications and model information for the Taymor Perspective Builders Series residential leverset, featuring solid metal construction, 4-in-1 adjustable latch, and various finishes. Includes ANSI Grade 3 rating and warranty details.
	Taymor Centinel 3 Bluetooth Digital Lock User Guide User guide for the Taymor Centinel 3 Bluetooth digital lock, covering overview, locking/unlocking, programming, troubleshooting, and factory reset procedures.
	Taymor Barcelona Knobset & Leverset: Specifications, Finishes, and Installation Guide Detailed specifications for the Taymor Barcelona Knobset and Leverset from The Premier Line. Covers features like Grade 3 security, reversible design, lifetime warranty, and fire rating. Includes installation guidelines, stocked and special order finishes (Matte Black, Satin Nickel, Satin Brass, etc.), product codes, and configuration options for round rose and square contemporary rose kits. Learn how to specify special order finishes with examples.
	Taymor Flush Deadbolt: Grade 2 Security, Features, and Specifications Detailed specifications for Taymor's Grade 2 Flush Deadbolt lock, including features like a 6-in-1 latch, anti-saw deadbolt, ADA compliance, available finishes, keyways (SC4, WR5), and installation dimensions.