eufy Security Floodlight Cam E 2K Quick Start Guide

Model: T8422

What's in the Box
Power On the Floodlight Cam Indoors
Set up the Floodlight Cam
Mount Floodlight Cam Outdoors
Safety
Customer Service

What's in the Box

The package includes:

Floodlight Cam E 2K (T8422)
Power Cord (Connected to the unit)
Mounting Plate
Installation Hook
Central Screw
Central Screw Cap
Wire Nuts (Connected to the unit)
Plate Screws

Power On the Floodlight Cam Indoors

1. Connect the Floodlight Cam to a power source. Wait approximately 1 minute or until the LED indicator blinks red.

[Diagram: Floodlight Cam E 2K connected to a power outlet via its power cord, with an LED indicator shown blinking red.]

Set up the Floodlight Cam

To set up your Floodlight Cam:

Download the eufy Security app from the App Store (for iOS devices) or Google Play (for Android devices).
Login or sign up for a eufy Security account.
Follow the on-screen instructions in the app to complete the setup.

Important: Ensure the Wi-Fi signal strength is strong at the intended installation location for streaming video from the Floodlight Cam.

Safety Warning: ⚠️ To avoid risk of shock, injury, or death, always be cautious when working with electricity. If you are uncomfortable working with electrical wiring, hire a professional electrician.

Mount Floodlight Cam Outdoors

Step 1: Unplug Floodlight Cam

Disconnect the Floodlight Cam from its power source.

[Diagram: Floodlight Cam being unplugged from a power source.]

Step 2: Prepare for Mounting

Unscrew the power cord; the wire nuts will be used later. The power cord is not required for outdoor mounting.

[Diagram: Floodlight Cam with its power cord being detached.]

Step 3: Shut Down Power

Shut down the circuit breaker that controls the power to the junction box where you will install the Floodlight Cam. Switch the lights on and off to confirm the electricity is properly shut off.

[Diagram: A circuit breaker panel with a switch being turned off.]

Step 4: Install Mounting Plate

Remove any existing floodlight fixture from the junction box. Install the new mounting plate to the junction box. The junction box and existing electrical wires are required for installation.

Ensure the concaved side of the mounting plate faces outwards.

[Diagram: An electrical junction box with an old fixture removed, and a new mounting plate being attached. Shows the orientation of the mounting plate.]

Step 5: Select Installation Method

You can hang the Floodlight Cam upside down or install it vertically on the wall. Select the method that best suits your junction box position.

[Diagram: Two mounting options shown: "Wall Mount" and "Eave Mount".]

Step 6: Hang Floodlight Cam

Hang the Floodlight Cam onto the junction box using the provided hook.

[Diagram: Floodlight Cam being hung on the mounting plate using a hook.]

Step 7: Connect Wiring

Ground Wire: Connect the ground wires (yellow or green) from the junction box and the Floodlight Cam using a wire nut. If the existing ground wire is connected to the junction box or there is no ground wire, connect the Floodlight Cam's ground wire directly to the junction box or mounting plate.

[Diagram: Shows connecting the ground wires together with a wire nut.]

Power Wires: Use wire nuts to connect the Floodlight Cam wires to the wires from the junction box. Connect the white wire (neutral) on the Floodlight Cam to the white wire from the junction box. Connect the black wire (hot) on the Floodlight Cam to the black wire from the junction box.

[Diagram: Shows connecting the white (neutral) and black (hot) wires using wire nuts.]

Step 8: Secure and Adjust

Insert the central screw through the center of the Floodlight Cam and screw it tightly. Use the central screw cap to cover the central screw to prevent rusting.

[Diagram: Shows inserting the central screw and then placing the screw cap over it.]

After installation, adjust the camera knobs on the Floodlight Cam to set your desired viewing angle.

Step 9: Power Up and Check

Switch on the main circuit breaker in your house.

Check if the Floodlight Cam is operating by verifying if the LED indicator has turned solid white.

Troubleshooting:

No Power: If the Floodlight Cam is not powered on, switch off the circuit breaker before checking the wiring.
Red Blinking LED: If the Floodlight Cam keeps blinking red, it indicates it is not connected to the Internet. Ensure the Wi-Fi signal is strong at the installation location. Consider moving your wireless router closer to the Floodlight Cam or using a Wi-Fi range extender.

For further troubleshooting, check the Help section in the Eufy Security app. Refer to the app for explanations of LED indicator status lights.

Safety

General Electrical Safety: ⚠️ Always be cautious when working with electricity to avoid risk of shock, injury, or death. It is recommended to hire a professional electrician if you are uncomfortable with electrical wiring.

Environmental Conditions: Do not use the device in environments that are too high or too low in temperature. Never expose the device to strong sunshine or excessively wet conditions. The suitable temperature range for the product and accessories is -20°C to 50°C.

Notices

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure conditions. The minimum separation distance is 20cm.

Shielded Cables

All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

Importer Information

Company Name: POWER MOBILE LIFE, LLC

Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541

Telephone: 1-800-988-7973

CE Declaration

This product complies with the radio interference requirements of the European Community.

Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the website www.eufylife.com.

RF Exposure Information

Wi-Fi Operating Frequency Range: 2412~2472MHz. Wifi Max Output Power: 16.09dBm(EIRP for 2.4G).

Bluetooth Operating Frequency Range: 2402~2480 MHz. Bluetooth Max Output Power: 8.61dBm(EIRP).

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements.

Recycling Information

This product is designed and manufactured with high-quality materials and components, which can be recycled and reused. This symbol [Recycling Symbol] means the product must not be discarded as household waste and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health, and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES-003.