eufy Security Floodlight Cam E 2K

What's in the Box

• Floodlight Cam E 2K (Model T84225)
• Power Cord (Connected to the unit)
• Mounting Plate
• Installation Hook
• Central Screw
• Central Screw Cap
• Wire Nuts (Connected to the unit)
• Plate Screws

Power On the Floodlight Cam Indoors

Step 1: Connect Floodlight Cam to a power source, and then wait 1 minute or until the LED indicator blinks red.

[Diagram Description: The Floodlight Cam is shown connected to a power outlet. An LED indicator light is visible on the device.]

Set up the Floodlight Cam

Install Floodlight Cam to the junction box outdoors (you need to have a junction box and wires already installed). In order to stream video from Floodlight Cam, you need to make sure the Wi-Fi signal strength is strong at the location you want to install Floodlight Cam.

[Warning Symbol] To avoid risk of shock, injury or death, always be cautious when working with electricity. Remember, do hire a professional electrician if you are uncomfortable working with electrical wiring.

Download the eufy Security app from the App Store (iOS devices) or Google Play (Android devices).

[Diagram Description: Icons for downloading from the App Store and Google Play.]

Login or sign up for a eufy Security account, then follow the onscreen instructions to complete setup.

Make sure you can livestream video from Floodlight Cam before mounting.

Mount Floodlight Cam Outdoors

Step 1: Unplug Floodlight Cam.

[Diagram Description: The Floodlight Cam is shown unplugged from its power source.]

[Warning Symbol] To avoid risk of shock, injury or death, always be cautious when working with electricity.

Step 2: Unscrew the power cord; wire nuts will be used later. The power cord is not required when mounting the Floodlight Cam outdoors.

[Diagram Description: The power cord is being unscrewed from the Floodlight Cam, showing wire nuts.]

Step 3: Shut down the circuit breaker in your house. Switch on/off the lights to make sure the electricity in your house is properly shut off.

[Diagram Description: A circuit breaker panel is shown, indicating the need to shut off power.]

[Warning Symbol] To avoid risk of shock, injury or death, always be cautious when working with electricity.

Step 4: Remove the old Floodlight from the junction box and install the mounting plate to the junction box. The junction box and existing electrical wires are required for Floodlight Cam installation.

[Diagram Description: An old fixture is removed from a junction box, and the new mounting plate is being installed.]

The concaved side of the mounting plate must face outwards.

Step 5: Select the installation method that best suits the position of your junction box. Users can hang Floodlight Cam upside down or install it vertically on the wall.

[Diagram Description: Two installation options are shown: Wall Mount and Eave Mount.]

For upside down installation, turn the cam down to the end when it's placed vertically, then turn the camera 180° in clockwise direction.

[Diagram Description: Two steps illustrating the adjustment for upside-down installation: positioning the camera vertically and then rotating it 180 degrees.]

[Warning Symbol] To avoid risk of shock, injury or death, always be cautious when working with electricity. Remember, do hire a professional electrician if you're uncomfortable working with electrical wiring.

Step 6: Hang Floodlight Cam on the junction box with the hook provided.

[Diagram Description: The Floodlight Cam is shown hanging from the junction box using the provided hook.]

Wiring Instructions:

Connecting Ground Wires

Connect both ground wires (yellow or green) from the junction box and Floodlight Cam, join the wires by using a wire nut. If the existing ground wire has been connected to the junction box or there's no ground wire, connect the ground wire of the Floodlight Cam to the junction box or mounting plate directly.

[Diagram Description: Visual representation of connecting the ground wires using a wire nut.]

Connecting Power Wires

Use wire nuts to connect Floodlight Cam wires to the rest of the wires from the junction box. Connect the white wire on the Floodlight Cam to the white wire (neutral) from the junction box. Connect the black wire on the Floodlight Cam to the black wire (hot) from the junction box.

[Diagram Description: Visual representation of connecting the white (neutral) and black (hot) wires using wire nuts.]

[Warning Symbol] To avoid risk of shock, injury or death, always be cautious when working with electricity. Remember, do hire a professional electrician if you're uncomfortable working with electrical wiring.

Step 7: Insert the central screw through the center of Floodlight Cam and screw it tightly. Use the central screw cap to cover the central screw to prevent the central screw from rusting.

[Diagram Description: The central screw is inserted through the camera, and then a screw cap is placed over it.]

Step 8: Adjust the camera to your desired angle using the cam knobs on Floodlight Cam.

Step 9: Switch on the main circuit breaker in the house. To check whether Floodlight Cam is operating, check if the LED indicator has turned solid white.

If Floodlight Cam is not powered on, switch off the circuit breaker before checking the wiring of Floodlight Cam.

[Warning Symbol] To avoid risk of shock, injury or death, always be cautious when working with electricity. Remember, do hire a professional electrician if you're uncomfortable working with electrical wiring.

If Floodlight Cam keeps blinking red, it means the floodlight is not connected to the Internet. Please make sure the Wi-Fi signal is strong at the desired location. You may consider moving the wireless router closer to Floodlight Cam or using a Wi-Fi range extender.

For troubleshooting, check the Help section in the Eufy Security app. Refer to the app page for what the LED indicator status lights mean.

Notice

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help.

FCC Radio Frequency Exposure Statement

The device has been evaluated to meet general RF exposure requirements. The device can be used in fixed/mobile exposure condition. The min separation distance is 20cm.

Notice: Shielded cables

All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

The following importer is the responsible party: Company Name: POWER MOBILE LIFE, LLC, Address: 400 108th Ave NE Ste 400, Bellevue, WA 98004-5541, Telephone: 1-800-988-7973.

This product complies with the radio interference requirements of the European Community.

Declaration of Conformity

Hereby, Anker Innovations Limited declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Web site www.eufylife.com.

Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment. The suitable temperature for the product and accessories is -20°C-50°C.

RF exposure information: The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.

Wi-Fi Operating Frequency Range:2412~2472MHz Wifi Max Output Power: 16.09dBm(EIRP for 2.4G). Bluetooth Operating Frequency Range:2402~2480 MHz; Bluetooth Max Output Power: 8.61dBm(EIRP).

Anker Technology (UK) Ltd | Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom

Anker Innovations Deutschland GmbH | Georg-Muche-Strasse 3, 80807 Munich, Germany

This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

[Recycling Symbol] This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.

IC Statement

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

IC RF Statement:

When using the product, maintain a distance of 20cm from the body to ensure compliance with RF exposure requirements. Lors de l'utilisation du produit, maintenez une distance de 20 cm du corps afin de vous conformer aux exigences en matière d'exposition RF.

Anker Innovations Limited Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

Customer Service

Warranty

12-month limited warranty

Call Us

• United States: +1 (800) 988 7973 (Mon-Fri 9AM-5PM PT)
• United Kingdom: +44 (0) 1604 936 200 (Mon-Fri 6AM-11AM GMT)
• Germany: +49 (0) 69 9579 7960 (Mon-Fri 6:00-11:00)

Email Us

Customer Support: support@eufylife.com

• Facebook: @EufyOfficial
• Twitter: @EufyOfficial
• Instagram: @EufyOfficial