Platform Bed Frame
Thank you for your purchase!
Product Sizes and Weight Capacity
The Platform Bed Frame is available in the following sizes, each with a specified weight capacity:
- Twin Size: 250 LBS
- Full Size: 400 LBS
- Queen Size: 400 LBS
- King Size: 400 LBS
Assembly Instructions
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during assembly.
Caution:
- Tighten all components securely before use. Failure to do so may result in personal injury.
- DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may result.
Warning:
- CHOKING HAZARD - Small Parts. Adult Assembly Required.
- DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE. Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The tipping restraint is intended only as a safety measure; it is not a substitute for proper adult supervision.
- To help prevent furniture from tipping over, it must be permanently attached to the wall. Anti-Tip Safety Wall Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Components
- (A) Headboard - 1pc
- (B) Headboard Side Legs - 2pcs
- (C) Headboard Middle Leg - 1pc
- (D) Footboard - 1pc
- (E) Siderails - 4pcs
- (F) Middle Brace - 1pc
- (G) Middle Cross Beam - 1pc
- (H) Middle Leg - 2pcs
- (I) Middle Brace Feet - 11pcs
- (K) Bed Legs - 2pcs
- (M) Screw $8*40 - 28pcs
- (L) Washers $8 - 11pcs
- (N) Allen Wrench - 1pc
- (O) Outer Slat Holders - 14pcs
- (P) Middle Slat Holders - 1pc
Assembly Steps
-
STEP 1:
Attach Headboard Side Legs (Part B) and Headboard Middle Leg (Part C) to Headboard (Part A) using (6) Washers (Part L) and (6) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N).
-
STEP 2:
Insert Bed Legs (Part K) into Footboard (Part D) and turn clockwise to tighten. Note: Screws preassembled on the footboard.
-
STEP 3:
Attach Middle Cross Beam (Part G) to Middle Leg (Part H) using (2) Washers (Part L) and (2) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N).
-
STEP 4:
Attach Middle Brace (Part F) to Middle Brace Feet (Part I) using (2) Washers (Part L) and (2) 8*40 Screws (Part M). Tighten with Allen Wrench (Part N).
-
STEP 5:
Attach Middle Brace (Part F) to Middle Cross Beam (Part G) using (1) Washer (Part L) and (1) 8*40 Screw (Part M). Tighten with Allen Wrench (Part N).
-
STEP 6A & 6B:
STEP 6A: Remove preassembled screws from middle leg. Attach Middle Cross Beam (Part G) to Middle Headboard Leg using preassembled screws. STEP 6B: Remove preassembled screws from Footboard. Attach Middle Brace to Footboard (Part D) using preassembled screws.
-
STEP 7:
Remove remaining preassembled screws from Headboard Side Legs and Footboard. Attach Siderails (Part E) to Headboard and Footboard using preassembled screws.
-
STEP 8:
Loosen preassembled screws from Siderails (Part E). Insert screws into the slots of the Middle Legs then tighten screws.
-
STEP 9:
Insert (28) Slats (Part J) into the left and right sides of the Middle Slat Holders (Part P). Insert Slats into Outer Slat Holders (Part O). Push down on slat holders to secure.
-
STEP 10:
Ensure all screws and slats are secure.
Customer Support
Quality products and first-class customer service are the cornerstone of long-lasting consumer relationships. Belnick strives toward excellence in all aspects and wants customers to be completely satisfied with their purchase.
Please contact Belnick's Customer Experience Agents at the email address or phone number shown below to assist with any product questions or issues before requesting a return.
Customer Service Email: CustomerExperience@belnick.com
Customer Service Phone: 866-552-2810
For warranty information, please visit www.belnick.com.
Ubique |
