Upholstered Platform Bed Assembly Instructions

Before You Begin

Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching during assembly.

Caution

Tighten all components securely before use. Failure to do so may result in personal injury. Do not use any sharp objects to open plastic wrapped components as damage to product or components may result.

Warning

CHOKING HAZARD - Small Parts. Adult Assembly Required. Injury may result from tipping furniture. You must install the Tipping Restraint Hardware with the unit to prevent the unit from tipping and causing any accidental injury, instability, death or damage. The tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision. This tipping restraint is not an earthquake restraint. If you wish to add the extra security of earthquake restraints, they must be purchased and installed separately. Serious or fatal crushing injuries can occur from furniture tipping over. To prevent furniture from tipping over it must be permanently fixed to the wall. Fixing devices for the wall are not included since different wall materials require different types of fixing devices. Use fixing devices suitable for the walls in your home. Failure to detach this restraint before moving furniture may result in injury or damage. Do not allow children to climb on furniture.

Parts List

• Part 1: Left & Right Side Rails (4 pcs) - Long, flat pieces forming the sides of the bed frame.
• Part 2: Headboard (1 pc) - The main backboard piece of the bed.
• Part 3: Footboard Legs (2 pcs) - Short, sturdy legs for the foot of the bed.
• Part 4: Headboard Legs (2 pcs) - Legs that attach to the headboard.
• Part 5: Left & Right Side Legs (2 pcs) - Legs that attach to the side rails.
• Part 6: Center Legs (4 pcs) - Support legs for the middle of the bed frame.
• Part 7: Center Rail (2 pcs) - A central support beam for the bed frame.
• Part 8: Support Slats (2 pcs) - Slats that support the mattress.
• Part 9: Footboard (1 pc) - The front piece at the foot of the bed.
• Part 10: Headboard Wings (2 pcs) - Decorative side panels for the headboard.

Hardware List

• Part A: M8 x 35mm Screws (10 pcs) - Medium-length screws with an 8mm diameter.
• Part B: M8 x 1mm Large Lock Washer (10 pcs) - Large washers with a 1mm thickness and an internal locking feature.
• Part C: M8 x 1mm Large Flat Washer (10 pcs) - Large flat washers with an 8mm inner diameter and 1mm thickness.
• Part D: M6 x 23mm Adjustable Height Glides (8 pcs) - Small threaded feet that can be adjusted for leveling.
• Part E: M8 x 20mm Screws (8 pcs) - Shorter screws with an 8mm diameter.
• Part F: M6 x 45 mm Screws (4 pcs) - Medium-length screws with a 6mm diameter.
• Part G: M6 x 50mm Screws (4 pcs) - Longer screws with a 6mm diameter.
• Part H: M6 x 25mm Screws (8 pcs) - Shorter screws with a 6mm diameter.
• Part I: M30 Self Tapping Screw (8 pcs) - Large screws designed to create their own thread.
• Part J: M6 x 1mm Small Lock Washer (12 pcs) - Small washers with a 1mm thickness and an internal locking feature.
• Part K: M6 x 1mm Small Flat Washer (12 pcs) - Small flat washers with a 6mm inner diameter and 1mm thickness.
• Part L: M4 x 95mm Small Allen Wrench (1 pc) - A small L-shaped tool for hexagonal sockets.
• Part M: M5 x 95mm Large Allen Wrench (1 pc) - A larger L-shaped tool for hexagonal sockets.
• Part N: M6 x 100mm Bolts (2 pcs) - Long bolts with a 6mm diameter.

Assembly Steps

Step 1: Attach Headboard Wings

Note: Unzip liner to access screw holes. Attach the Headboard Wings (Part 10) to both sides of the Headboard (Part 2) using four M8x35mm Screws (Part A), four M8x1mm Large Lock Washers (Part B), and four M8x1mm Large Flat Washers (Part C). Tighten using the M5 Large Allen Wrench (Part M).

Step 2: Attach Headboard Legs

Attach the Headboard Legs (Part 4) to the Headboard (Part 2) using six M8x35mm Screws (Part A), six M8x1mm Large Lock Washers (Part B), and six M8x1mm Large Flat Washers (Part C). Tighten using the M5 Large Allen Wrench (Part M).

Step 3: Attach Adjustable Height Glides to Headboard Legs

Attach two M6x23mm Adjustable Height Glides (Part D) to the Headboard Legs (Part 4).

Step 4: Attach Adjustable Height Glides to Footboard Legs

Attach two M6x23mm Adjustable Height Glides (Part D) to the Footboard Legs (Part 3).

Step 5: Attach Footboard Legs to Footboard

Attach the Footboard Legs (Part 3) to the Footboard (Part 9) using two M6x100mm Bolts (Part N). Tighten using the M4 Small Allen Wrench (Part L).

Step 6: Attach Side Legs to Side Rails

Attach two Side Legs (Part 5) to the Left and Right Side Rails (Part 1) using eight M6x25mm Screws (Part H), eight M6x1mm Large Lock Washers (Part J), and eight M6x1mm Large Flat Washers (Part K). Tighten using the M4 Small Allen Wrench (Part L).

Step 7: Attach Adjustable Height Glides to Side Legs

Attach two M6x23mm Adjustable Height Glides (Part D) to the Side Legs (Part 5).

Step 8: Attach Side Rails to Headboard Legs

Attach the Left and Right Side Rails (Part 1) to the Headboard Legs (Part 4) using four M8x20mm Screws (Part E). Tighten using the M5 Large Allen Wrench (Part M).

Step 9: Attach Adjustable Height Glides to Headboard Wings

Attach two M6x23mm Adjustable Height Glides (Part D) to the bottom of the Headboard Wings (Part 10).

Step 10: Attach Side Rails to Headboard Wings

Attach the Left and Right Side Rails to the Headboard Wings (Part 10) using four M6x50mm Screws (Part F), four M6x1mm Small Lock Washers (Part J), and four M6x1mm Small Flat Washers (Part K). Tighten using the M4 Small Allen Wrench (Part L).

Step 11: Attach Support Slats to Center Legs

Insert four M6x50mm Screws (Part G) through the Support Slats (Part 8) and the Center Rails (Part 7) and attach to the Center Legs (Part 6). Tighten using the M4 Small Allen Wrench (Part L).

Step 12: Attach Support Slats to Side Rails

Attach two sets of Support Slats (Part 8) to the Left & Right Side Rails (Part 1) using eight M30 Self-Tapping Screws (Part I). Tighten using a Phillips Screwdriver (Not Included).

Customer Service and Warranty

Have a Question/Concern?

Quality products and first-class customer service are the cornerstone of long-lasting consumer relationships. Please contact our Customer Experience Agents at the email address or phone number below to assist you with any product questions or issues before requesting a return. We look forward to serving you in a friendly, efficient manner to resolve any issues you may have.

Customer Service Email: CustomerExperience@belnick.com

Customer Service Phone: 866-552-2810

Our Warranty Statement

This warranty covers manufacturing defects associated with your new product. The product is warranted from the original purchase date and to the original purchaser for normal usage, according to the below-referenced specifications and limitations.

• Non-moving metal parts are warranted for 5 years.
• Component parts including pneumatic cylinder, control mechanism, base and casters are warranted for 2 years.
• All other items are warranted for 1 year.

Normal usage means use in compliance with the restrictions and weight limits specified for the product. In the absence of product-specific restrictions and weight limits, normal usage means use for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage terminates if the product is sold or otherwise transferred. Repairs made by parties other than Belnick also void this warranty.

This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use by persons exceeding specified weight limits or commercial use exceeding forty hours per week; or (5) rust or other damage caused by exposure to moisture. The user assumes all risk of injury resulting from use of this product. Liability for incidental or consequential damage is excluded. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.