Minelab Metal Detector Compliance, Safety, and Regulatory Information
General Safety and Disposal Information
This symbol ♻️ indicates that the equipment and its electrical accessories should not be disposed of as household garbage. These items should not be disposed of as unsorted municipal waste and must be taken to a certified collection point for recycling and proper disposal. Refer to Directive 2012/19/EU (Waste Electrical and Electronic Equipment).
For Battery regulatory information: www.minelab.com/b
For Environmental Labelling information: www.minelab.com/e
Safety Considerations:
- Keep out of reach of children, small parts are a choking hazard.
- Do not mutilate the batteries.
- Dispose of batteries as per local regulations.
- Only charge the detector and accessories according to the instructions in the manual.
- Do not dispose of the detector or accessories in a fire.
- Disconnect coil before packing/storing as luggage.
- CAUTION -- Risk of explosion if battery is replaced by an incorrect type.
- CAUTION -- Only charge the battery in ambient temperatures between 0°C and 40°C.
- Headphone use at HIGH volume may cause reduced awareness of surroundings and could lead to hearing damage. Use at lower volumes advised.
- Adult supervision required when used by children.
Regulatory Information
Federal Communications Commission (FCC) Statements (as applicable)This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Part 15.105 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
US Responsible Party: MINELAB AMERICAS INC, 3565 Butterfield Rd. Unit 121 Aurora, IL 60502, USA ComplianceManager@minelab.com.au
Compliance Statements for Canada (as applicable)This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RSS-Gen notice: This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions: 1) This device may not cause interference; and 2) This device must accept any interference, including interference that may cause undesired operation of the device.
ModificationAny changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the device.
Simplified EU & UKCA Declaration of ConformityHereby, Minelab Electronics Pty Ltd declares that the radio equipment type [Refer to equipment listed in Table 1] complies with Directive 2014/53/ EU and The Radio Equipment Regulations 2017 (S.I. 2017/1206). Full text of the EU & UKCA declarations of conformity are available at the following internet address: www.minelab.com/compliance.
EU Importer & Auth. Representative: Minelab International Ltd., Penrose Dock, T23KW81, Ireland | minelab@minelab.ie
License / PermitThe equipment operator is responsible for investigating and obtaining any required local license or permit for metal detecting activities.
Warranty Terms
Please refer to www.minelab.com/support/product-warranty for full warranty terms and conditions.
Register your product warranty online at register.minelab.com.
Assembly Instructions
For guidance on detector assembly, please refer to the Getting Started Guide included or visit: www.minelab.com/product-manuals. The Minelab website also provides information on accessories available for your detector.
Model Certifications
The following table lists various Minelab metal detector models and their associated certification information.
| Detector | Frequency | Power (dBm) | Certification Scheme ID | FCC ID | ISED | MIC | Anatel | BIS/ETA |
|---|---|---|---|---|---|---|---|---|
| VANQUISH 540 | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20210100676 | 2APN8-ML80 | 24927-0041 | 001-A16239 | -- | R-41220116 |
| VANQUISH 340 / 440 | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20210100634/636 | Z4C-0022 | 24927-0022 | 001-A19879 | 03956-21-11695 | R-41211974 |
| EQUINOX 600 / 800 | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20221210452/465 | Z4C-0054A | 24927-0054A | 04023-21-11695 | 17411-20-11695 | R-41206482 |
| EQUINOX 700 / 900* | 2.4 to 2.5 Ghz | < -30 dBm | ETA-SD-20230301955 | Z4C-0054 | 24927-0054 | 001-A19879 | 003-180034 | R-41206482 |
| X-Terra Pro | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20231211208 | Z4C-ML80A | 24927-ML80A | 001-A19879 | 21898-22-11695 | R-41206482 |
| X-Terra Elite | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20210100667 | Z4C-ML100A | 24927-ML100A | 001-A19879 | 21925-22-11695 | R-41236608 |
| CTX 3030 | -- | < -30 dBm | ETA-SD-20210100638/640 | Z4C-ML85 | 24927-ML85 | -- | -- | -- |
| GO-FIND 44 / 66 | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20221210303 | Z4C-ML105 | 24927-ML105 | -- | -- | R-41206482 |
| GO-FIND 11 / 22 | 2.4 to 2.5 GHz | < -30 dBm | -- | Z4C-0061 | 24927-0061 | -- | 23503-23-11695 | R-41206482 |
| Excalibur II | -- | < -30 dBm | R-41206482/R-41240427 | -- | -- | -- | -- | -- |
| Manticore* | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20230201248 | -- | -- | 06876-18-11695 | -- | R-41248320 |
| PRO-FIND Series | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20230201251 | -- | -- | 05531-20-11695 | -- | R-41206482 |
| Gold Monster 1000 | 2.4 to 2.5 GHz | < -30 dBm | ETA-SD-20230201251 | -- | -- | 04112-21-11695 | -- | R-41216798 |
| SDC 2300 | -- | < -30 dBm | ETS-SD-20221210937 | -- | -- | -- | -- | R-41216798 |
| GPZ 7000 | -- | < -30 dBm | ETA-SD-20221210297 | -- | -- | -- | -- | -- |
| GPX 5000 | -- | < -30 dBm | R-41216798 | -- | -- | -- | -- | -- |
| GPX 6000 | -- | < -30 dBm | ETA-SD-20221210923 | -- | -- | -- | -- | -- |
| ML 80 | 5 to 143 kHz | 0 dBm | -- | -- | -- | -- | -- | R-R-Tej-ML80A |
| ML 100 | 3.7 to 143 kHz | < -30 dBm | -- | -- | -- | -- | -- | R-R-Tej-ML100A |
| ML 85 | 2.5 to 143 kHz | < -30 dBm | -- | -- | -- | -- | -- | R-R-Tej-ML85 |
| ML 105 | 2.5 to 143 kHz | < -30 dBm | -- | -- | -- | -- | -- | R-R-Tej-ML105 |
| WM 09 | 1.3 to 141 kHz | < -30 dBm | -- | -- | -- | -- | -- | R-R-Tej-0061 |
* indicates use of e-labelling; follow instructions in Manual/carton to access.
Certification and logo usage dependant on product and region.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Minelab Electronics Pty Ltd is under license. Other trademarks and trade names are those of their respective owners.
Disclaimer
The Minelab metal detector discussed in this instruction manual has been expressly designed and manufactured as a quality hobbyist metal detector and is recommended for use in coin, treasure and general metal detection in non-hazardous environments. This metal detector has not been designed for use as a mine detector or as a live munitions detection tool.
Metal Detectors | Minelab Metal Detectors
MINELAB - Register Your Minelab
Detectores de Metales Minelab Detectores de metales de alto rendimiento
Metal Detectors | Minelab Metal Detectors
quefairedemesdechets.fr
