COSTWAY HW67486 Folding Working Table

Assembly Instructions and User Manual

With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE!

Maximum Recommended Weight Loads

MAXIMUM LOAD: 200 lb. (90.7 kg)

MAXIMUM LOAD: 50 lb. (22.6 kg)

WARNING: THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

Cam Lock System Operation

HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS:

Screw the cam bolt into the threaded inserts on the panel. Connect both panels together, making sure the cam bolt goes into the pre-drilled hole on the end of the panel for the cam lock.
Insert the cam lock into the pre-drilled large hole on the panel. Make sure the arrow on the face of the cam lock faces out and points towards the cam bolt.
Take a Phillips screwdriver and rotate the cam lock clockwise to lock the cam bolt in place.

You are now ready to assemble the KD unit.

Parts and Hardware List

Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly.

Parts:

A - Large Top Panel (Qty. 1)
B - Small Top Panel (Qty. 1)
C - Fixed Shelf (Qty. 2)
D - Back Panel (Qty. 1)
E - Left End Frame (Qty. 1)
F - Middle End Frame (Qty. 1)
G - Right End Frame (Qty. 1)
H - Metal Bar (Qty. 2)

Hardware:

(1) Cam Lock (Qty. 8+1 extra)
(2) Cam Bolt (Qty. 8+1 extra)
(3) M6 x 12 mm Bolt (Qty. 4+1 extra)
(4) M6 x 25 mm Bolt (Qty. 2+1 extra)
(5) M6 x 50 mm Bolt (Qty. 4+1 extra)
(6) M4 x 15 mm Screw (Qty. 18+1 extra)
(7) Locator Pin (Qty. 1)
(8) Butt Hinge (Qty. 2)
(9) Swivel Caster (Qty. 3)
(10) Locking Caster (Qty. 3)

Tools Required:

Hex Wrench (Qty. 1)
Open Wrench (Qty. 1)
Phillips screwdriver (not provided)

Assembly Instructions

Step 1: Preparation

Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch.

Step 2: Prepare End Frames

Lay out the Left End Frame (E) and Right End Frame (G) with the holes facing up. Securely screw the Cam Bolts (2) into the threaded sockets as shown.

Step 3: Attach Fixed Shelves

Attach two Fixed Shelves (C) to the Middle End Frame (F) by engaging two Cam Locks (1) in each. Ensure the cam locks face the floor when the unit is turned upright.

Step 4: Attach Right End Frame

Repeat the same procedure to attach the Right End Frame (G) at the opposite end.

Step 5: Combine Top Panels

Combine the Top Panels (A and B) together by attaching two Butt Hinges (8) at the joint with six 15 mm Screws (6) per hinge, using the pilot holes as a guide.

Step 6: Install Locator Pin

Securely screw one Locator Pin (7) into the threaded insert on the Large Top Panel (A).

Step 7: Attach Pedestal to Small Top Panel

Attach the assembled pedestal (formed by frames F, G, and shelves C) to the Small Top Panel (B) with four 50 mm Bolts (5) as shown.

Step 8: Attach Metal Bars

Attach two Metal Bars (H) to the back of the End Frames (F and G) with four 12 mm Bolts (3).

Step 9: Attach Back Panel

Using the pilot holes as a guide, attach the Back Panel (D) to the pre-attached hinges on the Middle End Frame (F) with six 15 mm Screws (6).

Step 10: Connect Left End Frame to Top Panel and Back Panel

Position the front post of the Left End Frame (E) onto the Locator Pin (7) installed on the Large Top Panel (A) and attach to the Back Panel (D) with two 25 mm Bolts (4).

Step 11: Install Casters

Attach three Swivel Casters (9) to the front posts and three Locking Casters (10) to the back posts of the End Frames (E, F and G). Tighten the casters in place with the provided open wrench.

Step 12: Position the Unit

Ask for assistance to lift the unit upright and position at the desired location.

Step 13: Folding the Table

You can collapse the Large Top Panel (A) to save space. To fold the desk, lift up the Large Top Panel (A) a little so that you can swing the Left End Frame (E) all the way to the front of the right pedestal, then lay down the Large Top Panel.

Step 14: Extending the Table

Extend the Large Top Panel (A) in reverse order as needed.

	Costway NP10265 Folding Table User Manual and Instructions Comprehensive guide for the Costway NP10265 folding table, covering setup, unfolding, folding, and return/damage claim procedures. Includes safety precautions and contact information.
	Costway Folding Computer Desk CB10359 Assembly Instructions and Safety Guide A comprehensive guide for assembling the Costway Folding Computer Desk (Model CB10359). This document provides detailed step-by-step assembly instructions with textual descriptions of diagrams, a complete parts and hardware list, essential safety precautions, and procedures for returns or damage claims.
	Costway Folding Picnic Table Assembly and Safety Instructions Comprehensive instructions for assembling and safely using the Costway Folding Picnic Table (NP11267), including parts list, assembly steps, and important safety information.
	Costway TH10037 Folding Hand Truck: Assembly and Safety Guide Comprehensive user manual for the Costway TH10037 Folding Hand Truck. Provides detailed assembly instructions, safety precautions, and operational guidance for efficient and secure transport.
	Costway HW67176 L-Shaped Corner Computer Desk Assembly Guide User manual for the Costway HW67176 L-Shaped Corner Computer Desk. Includes parts list, hardware, and step-by-step assembly instructions for easy setup.
	Costway HW65911BN Console Table Assembly Instructions Detailed assembly instructions and safety information for the Costway HW65911BN Console Table, including a parts list and step-by-step guide.
	Costway KC55737 Dining Table Set Assembly Instructions Comprehensive assembly instructions for the Costway KC55737 Dining Table Set, including parts list, assembly steps, and safety information. This set includes a dining table, two chairs, and a bench.
	Costway Foldable Chaise Lounge with Cushion (HW63881) - Assembly Instructions and Product Information This document provides comprehensive assembly instructions, safety guidelines, parts list, and return/damage claim procedures for the Costway Foldable Chaise Lounge with Cushion, model HW63881. It is designed for easy assembly and safe use.