NodOn ON/OFF Lighting Relay Switch

Product Specifications

• Power supply: 230V AC ~ 50Hz
• Switching capabilities: 230V AC - 2 x 5A
• Consumption: <1W
• Maximum output power: 2 x 1150W (Resistive load)
• List of compatible loads: available on nodon.fr/loads
• Radio frequency range: 868.0 to 868.6 Mhz
• RF power max: +3dBm
• Range: up to 30m indoor
• Operational temperature: -10°C to 40°C
• Protection rating: IP 30
• Pairing: up to 22 controllers
• EEP (EnOcean Profile): D2-01-12
• Dimensions: 40 mm (width) x 44 mm (length) x 16.9 mm (height)
• Weight: 34 g
• Warranty: 2 years

Use Cautions

• Never use the device if it is not correctly installed and placed inside a connecting box in conformity with the current norms.
• Keep the product far away from liquids.
• This product is conform to EnOcean radio protocol.
• This product must be used indoor only.

Approvals and Certifications

The presence of the CE symbol indicates conformity with European directive 2012/19/UE. Information regarding the separate collection of electrical and electronical devices is available in your region. Respect local rules and do not dispose of the product with domestic waste. Correct disposal helps protect the environment and health.

NodOn SAS declares that this radio equipment is conform to the RED directive 2014/53/UE. The full text of the EU declaration of conformity is available at: nodon.fr/en/ “support” section.

Danger of Electrocution

BEFORE ANY INSTALLATION MAKE SURE THE POWER SUPPLY IS DISCONNECTED TO AVOID ANY RISK OF ELECTROCUTION. Directly cut the power supply from the breaker box. A wrong installation can create a fire or an electric shock. If you are not confident about electrical installation, please ask a professional.

The relay switch must be installed and connected carefully following the instructions of this user guide. NodOn SAS will not be responsible for any loss or damage resulting from a non-respect of the instructions. Cut the power supply before any operation and do not make any modification if the LED is still ON.

Installation

Thanks to its small size, the ON/OFF Lighting Relay Switch can be installed anywhere in the wall or the ceiling (behind an existing wall switch, in a false ceiling, etc.).

TIP: Add the ON/OFF Lighting Relay Switch to the electric panel with NodOn DIN Rail Box*.

*Optional accessory

Relay Switch Input/Output

Each terminal can accept a cable of 2.5mm² maximum, stripped of 8mm.

• N: Terminal for the Neutral
• L: Terminal for the Line
• Input terminal for the wired switch 1*: Controlled by 1
• Input terminal for the wired switch 2*: Controlled by 2
• Output 1: Controlled by 1
• Output 2: Controlled by 2

*Wired switch optional (see the installation diagrams section)

Installation Diagram for One or Two Lights

Wiring with one or two ways

1. Cut the power supply.

2. Dismantle the wired switch controlling the light(s) you want to connect.

3. Install the ON/OFF Lighting Relay Switch according to diagram figure 1.

4. Reinstall the wired switch.

5. Turn the power supply back ON.

Figure 1: Diagram showing the wiring connections for the relay switch with one or two lights, including neutral (N) and line (L) inputs, and connections for wired switches and outputs.

Auto-Detection of Switch Type

After turning the power supply ON, do a single push on the wired wall switch. The relay switch has an auto-detection system to automatically detect the type of wired wall switch (rocker or push-button) wired at the input.

Note: The same configuration is applied for both inputs (1 and 2). It is not possible to combine a rocker switch with a push-button. To perform a new auto-detection, the ON/OFF Lighting Relay Switch must be manually reset (see reset procedure).

Pairing Procedure

To add a remote or a wall switch or the Soft Button (EnOcean compatible), you must enter the pairing mode, and your light must be switched OFF. The relay switch must be power supplied.

For Channel 1 (1/1)

Two modes:

1. From the module: Launch the pairing by doing 3 consecutive presses on the relay switch button. The LED blinks red.
2. From the wired wall switch: Activate the wired wall switch 3 times (in less than a second). The lighting connected in 1 blinks, meaning that the channel 1 (1/1) is in “pairing/unpairing mode”.

You have 30 seconds to pair your controller by briefly pressing (in less than a second) on the button of your choice. This will turn the light ON for channel 1, and the opposite button will turn it OFF.

The LED of the relay switch will blink green twice, confirming the pairing of the two devices. The light stops to blink, confirming the pairing of the two devices.

For Channel 2 (2/2)

Two modes:

1. From the relay switch: Launch the pairing by doing 3 consecutive presses on the relay switch button. The LED blinks red. Wait 1 second and do a new press on the relay switch button.
2. From the wired wall switch: Press the wall switch 3 times (in less than a second). Wait 1 second and do a new press on the wall switch. The light connected in 2 blinks, meaning that the channel 2 (2/2) is in “Pairing/Unpairing” mode.

Continue with steps 2 and 3a/3b to pair your controller.

Note: If the LED blinks orange during the pairing procedure, it means that more than 22 controllers are paired and that no more controllers can be paired. You must remove one controller to add a new one.

Use of your Soft Button

You have 30 seconds to pair your Soft Button by doing 5 brief consecutive presses on the button.

Pairing with a Home Automation Gateway

For more details on how to pair a home automation gateway or other compatible products, please consult the “Support” section on nodon.fr/en/.

Unpairing Procedure

Do the same procedure as pairing (see “Pairing Procedure”) and take care of pressing the button chosen to control your gate/garage door/electric latch or your electrical outlet.

Reset Procedure

The module must be connected and powered ON.

1. Press more than 5 seconds on your module’s button. The LED blinks orange.
2. Press once again the button (short press) to confirm the reset. If the reset is correct, the LED blinks alternatively in red and green and stays green. Start again if necessary.

Your module has now its original settings.

Detailed User Guide

Directly access the detailed user guide on the Support section on nodon.fr/en/technical support/.