Zuolog Inc. Installation Instructions for One Piece Toilet

Important Safety Information

ATTENTION! READ ALL INSTRUCTIONS BEFORE UNPACKING THE PRODUCT.

Instructions that, if ignored, could result in death or serious injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation.

• 2 PEOPLE ARE REQUIRED TO LIFT AND DURING THE ENTIRE INSTALLATION OF THIS PRODUCT.
• Installation of this product by an inexperienced installer may result in personal injury or death!

Zuolog Inc. reserves the right to change, update, modify, or redesign this manual/product or its policies without prior notice. It is your responsibility to visit the website to download or contact customer service for the most updated version of the installation instructions.

Zuolog Inc. shall not be liable for any injuries or property damages in connection with this product during installation or use of this product.

• Limited warranty is void on any commercial installation.
• Zuolog Inc. is not responsible for local code compliance for this product.
• Building and plumbing codes may vary from state-to-state in accordance to your location.
• Zuolog Inc. is not responsible for providing any compliance certifications.
• Under no circumstances shall Zuolog Inc. be liable for any and all incidental damages sustained in connection with this product. Neither the manufacturer, nor distributor, nor retailer is responsible for water damage or flood caused due to use of this product.
• Under no circumstances shall Zuolog Inc. be liable for any and all fees, cost of installation/re-installation/removal, subsequent damage, or transportation in case of the product defect.

Tools Required for Installation

• Silicone
• Level
• Tape Measure
• Socket extension
• Safety Glass
• Putty Knife
• Knife
• Soft Cloth
• Pencil/Marker
• Channel Pliers
• Wrench
• Wrench

Installation Instructions

1. Install Closet Bolts: Install closet bolts in flange channel, turn 90°, and slide into place 6" apart and parallel to wall.
2. Install Wax Seal: Invert toilet on floor (cushion to prevent damage), and install wax ring evenly around waste flange (horn), with tapered end of ring facing toilet. Apply a thin bead of sealant around toilet base.
3. Position Toilet on Flange: Unplug floor waste opening and install toilet on closet flange so bolts project through mounting holes. Adhere the side bolt covers to toilet. Loosely install retainer washers and nuts. Position toilet squarely to wall and, with a rocking motion, press bowl down fully on wax ring and flange. Alternately tighten nuts until toilet is firmly seated on floor.
4. Install the Side Cover: Attach the side cover components (Cap, Side cover, Hook, Washer, Screw, Plastic Disc, Floor Bolt) as shown in the diagram.

Maintenance Instructions

1. Periodical Maintenance
   • Wash the toilet seat with a soft wet cloth.
   • Dry with a soft dry cloth.
2. Removal of Stains
   • Use neutral detergent (e.g., soap powder) to wipe softly, then dry with a clean cloth.
   • Do not use eradicator, abrasive powder, diluent, volatile oil, acid or alkali liquid detergent, and nylon brush to clean the product to avoid damage.

Care Instructions & Precautions

Please read carefully the following maintenance manual in order to avoid component damage or injury to the installer. Keep the maintenance manual available for future maintenance or reference.

Follow all safety precautions to avoid personal injury or property damage.

Prohibited Acts:

• Do not open/close the seat cover using unnecessary force. (It might cause cracks or failure on performance)
• Heavy loading may damage the seat cover and may cause a fall.
• Do not use strong abrasive cleansers, which might cause damage to the surface.
• Clean the surface of the toilet seat with mild soap water.
• Use a clean and soft cloth to wipe the toilet seat until it is completely dry.
• Keep children out of reach of the seat, to avoid personal injury.
• Do not open/close the seat cover using unnecessary force. (It might cause cracks or failure on performance)
• Do not expose the seat cover directly to sunlight. (It might cause color fading)

Toilet Seat Installation

1. Toilet Seat Installation Package: The package includes 2*long bolt, 2*stainless steel washer, 2*Nylon expansion plug.

2. Install Nylon Plugs: Put the nylon pop plug into the toilet mounting hole.

3. Position Toilet Seat: Place the toilet seat onto the toilet bowl with the hinge base overlapping the bolt holes in the bowl.

4. Insert Bolts and Tighten: Insert stainless steel gasket into hinge mounting hole. Insert the long bolts through the mounting holes from the top. Use a screwdriver to tighten the screws.

5. Check Installation: Please check if it is installed properly, check if it is already tight and not shaking. If shaking occurs, you need to re-adjust the position of the toilet seat mounting holes and the position between the toilet. If the toilet seat is completely consistent, it will not loosen.

6. Close Hole Covers: In the last step, if there is no problem, you need to close the lid of the installation hole on the toilet seat.