Lutron Caséta Wireless In-Wall Dimmer PRO

Double Your Warranty

Share your feedback and ideas for Caséta Wireless dimmers to extend your warranty by 1 year. Visit www.casetawireless.com/register.

Installing Your Dimmer

Installation for lights with one wall switch (single pole).

1. Turn Power Off

   Turn off power at the circuit breaker or fuse before installing. ⚠️ [Warning: Shock Hazard. May result in serious injury or death.]

2. Remove Existing Switch

   Remove the wallplate from the switch. Remove the switch and pull it away from the wall. Disconnect all wires from the switch.

   If your switch has more than 3 wires, refer to the installation video at www.casetawireless.com/3way.

3. Remove Side Sections (If Necessary)

   Side sections of the dimmer may need to be removed depending on the wallbox configuration. Bend back and forth to remove. Do not remove outside side sections on dimmers at the end of a gang. Each dimmer has inside side sections removed. A dimmer in the middle has all side sections removed.

4. Connect the Dimmer

   Wire connections:

   • Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.
   • Connect the load wire from the wallbox to the red wire on the dimmer using a wire connector.
   • Connect the hot wire from the wallbox to the black wire on the dimmer using a wire connector.
   • If available, connect the neutral wire from the wallbox to the white wire on the dimmer. If neutral is not available, cap the white wire with a wire connector. [Note: Neutral wire is required for MLV loads, LED drivers, PHPM PA, PHPM-3F, GRX-TVI.]
   • Cap the blue wire with a wire connector. [Note: The blue wire is only used for a 3-way installation with a mechanical toggle switch. See www.casetawireless.com/3way for details.]

5. Mount the Dimmer

   Use the provided screws to mount the dimmer into the wallbox.

6. Attach the Wallplate

   Attach the adapter to the dimmer using the provided screws and snap on the wallplate. If installing next to other devices, ensure the wallplate has the correct number and size of openings.

7. Turn Power On

   Turn power back on at the circuit breaker.

Important Note: 3-Way Installation

If more than one switch controls the light, this is a 3-way installation. You will need to purchase a PJ2-WALL-WH-L01. Visit www.casetawireless.com/3way for more details.

Important Note on Wattage Derating

Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information.

For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

Using Your Caséta Wireless Kit

The Caséta Wireless dimmer can be controlled from a smartphone when used with the Lutron Smart Bridge (sold separately).

With a Smartphone or Tablet (Bridge Required)

1. Download the Lutron app from the App Store or Google Play. Search for "Lutron Caseta".
2. Launch the Lutron app. The app will guide you through setting up your devices.
3. Follow the app's instructions, which may involve pressing buttons on the dimmer and remote.

If using a bridge from another manufacturer, refer to their instructions.

Without a Smartphone or Tablet (Bridge Not Required)

Pairing the dimmer and Pico remote control:

1. Press and hold the "off" button on the dimmer for 6 seconds until LEDs start blinking.
2. Press and hold the "off" button on the Pico remote for 6 seconds until lights flash 3 times.
3. Press and hold the "favorite" button on the Pico remote for 6 seconds until LEDs blink twice on the dimmer. The new favorite level is now saved.

Repeat steps to pair other Pico remote controls.

Changing the Favorite Light Level on the Pico Remote

The round "favorite" button on the Pico remote recalls a favorite light level (default is 50%). To change it:

1. Set the desired light level on the dimmer.
2. Press and hold the "favorite" button on the Pico remote for 6 seconds until LEDs blink twice on the dimmer. The new favorite level is now saved.

Replacing Light Bulbs using FASSTM

Pull the FASSTM switch out on the In-wall Dimmer PRO to remove power at the light socket. [FASSTM switch] [light bulb socket]

Using Your Controls

In-wall dimmer PRO:

• On/Off: Press the top/bottom buttons.
• Brighter: Press the raised icon button.
• Darker: Press the lower button.
• Favorite: Press the round button.

Pico remote control (sold separately):

• On: Press the top button.
• Off: Press the bottom button.
• Brighter: Press the right button (with raised icon).
• Darker: Press the left button.
• Favorite: Press the round button.

Troubleshooting

For additional troubleshooting suggestions, visit www.casetawireless.com/support.

Compatible Light Bulbs

Works with compatible energy-efficient dimmable light bulbs:

• LED: up to 250 W
• Incandescent / Halogen: up to 1000 W
• MLV Halogen: up to 1000 VA

Dimmable LED light bulbs vary in dimming performance. If bulbs flicker or turn off, visit www.casetawireless.com/lowend.

For a complete list of compatible dimmable LEDs, visit www.casetawireless.com/bulblist.

Compatible bulbs include:

• EcoSmart® ECS BR30 W27 FL 120
• EcoSmart® ECS 20 WW FL 50WE 120
• Feit® A19/OM/LED
• Philips® 9290002295
• Sylvania® LED12A19/DIM/O/827
• Sylvania® LED21PAR38/DIM/P/930/FL30

Device Ratings

In-wall dimmer PRO PD-10NXD: 120 V~ 50/60 Hz

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

Codes and Grounding

Install in accordance with all national and local electrical codes.

When no grounding means exist in the wallbox, the National Electrical Code (NEC®) allows installation if a nonmetallic faceplate is used or the circuit is GFCI protected. In such cases, cap or remove the green wire before screwing the control into the wallbox.

FCC/IC Information

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standards. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment causes harmful interference to radio or television reception, try to correct it by reorienting the antenna, increasing separation between equipment and receiver, or connecting to a different circuit. Consult a dealer or technician if needed.

Warranty

For warranty information, please visit www.casetawireless.com/warranty.

Manufacturer Information

Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.

Lutron, Caséta, and Pico are registered trademarks. FASS and Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association. Google and the Google logo are registered trademarks of Google Inc.

©2015 Lutron Electronics Co., Inc.

P/N 0301778 REV A