Lutron Caséta Wireless In-Wall Dimmer PD-6WCL Quick Start Guide

Introduction

Welcome and thank you for purchasing a Caséta™ Wireless in-wall dimmer. To control your lights from an app or remote, you'll need to replace an existing switch with a Caséta™ Wireless in-wall dimmer.

We hope you enjoy the convenience of Caséta™ Wireless!

Double Your Warranty: Love Caséta™ Wireless dimmers? Have ideas for making them better? Tell us what you think and we'll extend your warranty by 1 year. Visit www.casetawireless.com/register.

Before installing, watch the installation video at www.casetawireless.com/support.

What's Included

• In-wall dimmer (PD-6WCL) [dimmer]
• Wire connectors (3) [wire connector]
• Screws (2) [screw]

Tools You'll Need

• Flat-head screwdriver [flat-head screwdriver]
• Phillips-head screwdriver [phillips-head screwdriver]
• Pliers [pliers]

Compatibility

Works with energy efficient dimmable light bulbs:

• LED: up to 150 W
• CFL: up to 150 W
• Halogen: up to 600 W
• Incandescent: up to 600 W

Note: You can mix and match dimmable LED and CFLs, as well as halogen and incandescent light bulbs, with Caséta™ Wireless dimmers. Dimmable LED and CFL light bulbs vary in their dimming performance. If you're using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.

For a complete list of compatible dimmable LEDs and CFLs, please visit www.casetawireless.com/bulblist.

Compatible light bulbs include models from Cree®, EcoSmart®, Feit®, Philips®, and Sylvania®.

Installation Guide: Single Pole Switch

WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

1. Turn Power Off at Circuit Breaker

   [Power OFF] Turn power off at circuit breaker!

2. Remove Existing Switch from Wall

   Remove the wallplate from switch. Remove the switch and pull it away from the wall. Disconnect all three wires* from the switch.

   *If your switch has more than 3 wires attached, see the "Installing Caséta Wireless in a 3-way switch application" video at www.casetawireless.com/3way.

   Important Note: Some lights have one wall switch, while others have two or more wall switches (such as stair lights). This guide is for single-pole (one switch) lights. For 3-way switches, visit www.casetawireless.com/3way for complete instructions.

3. Remove Side Sections (If Necessary)

   For ganged installations (dimmer next to other devices), remove the inner side sections of the dimmer. The dimmer at the middle of a gang has all side sections removed. Do not remove outside side sections on dimmers at the end of a gang.

   Important Note: Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information.

   Maximum Wattage Derating Chart (120 V~ 50/60 Hz)

   Side Sections Removed	None	1 Side	2 Sides
   LED & CFL	150 W or*	150 W	150 W
   Incandescent & Halogen	600 W	500 W	400 W

   *For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

4. Connect the Dimmer

   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector.

   2. Connect either of the remaining wires from the wallbox to either of the remaining wires on the dimmer using a second wire connector.

   3. Connect the remaining wire from the wall to the remaining wire on the dimmer using a third wire connector.

   [Diagram showing wire connections: Ground to Green, Wire 1 to Wire 1, Wire 2 to Wire 2]

5. Mount the Dimmer

   Use the screws provided. [Diagram showing dimmer being screwed into wallbox]

6. Attach the Wallplate

   Attach the adapter to the dimmer using the screws provided and snap on the wallplate. [Diagram showing wallplate attachment]

   (If you installed the dimmer next to other dimmers or switches, you'll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)

7. Turn Power On at Circuit Breaker

   [Power ON] Turn power on at circuit breaker!

Using Your Caséta™ Wireless Kit (Sold Separately)

With a Smartphone or Tablet (Bridge Required)

The Caséta™ Wireless dimmer can be controlled from a smartphone when used with the Lutron® Smart Bridge™. If you are using the dimmer and remote control with the Lutron® Smart Bridge™, follow the instructions below.

Note: If you are using the dimmer and remote control with another manufacturer's bridge, please refer to that manufacturer's instructions for set-up.

1. Download the Lutron® App

   Search for "Lutron Caseta" on the App Store [App Store] or Google Play [Google Play].

   www.casetawireless.com/LutronApp

   The Lutron® app will walk you through setting up your devices.

2. Use the Lutron® App to Complete Remaining Steps

   The app guides you through adding devices:

   • Add Devices: Pico® remotes, Dimmers, Shades [Add device]
   • Control three ways [Three-way control]
   • Schedule your lights [Schedule lights]
   • Connect while away [Remote access]

Without a Smartphone or Tablet (Bridge Not Required)

Pairing the dimmer and Pico® remote control:

1. Press and hold the "off" button on the dimmer for 6 seconds until LEDs start blinking. [Diagram showing pressing dimmer 'off' button]
2. Press and hold the "off" button on the remote for 6 seconds until lights flash 3 times. Repeat for other Pico® remotes. [Diagram showing pressing remote 'off' button]

Changing the favorite light level on the Pico® remote control (sold separately):

You can use the round "favorite" button on the Pico® remote control to recall a favorite light level. We've set it to 50%, but you can change it to any level you like.

1. Set desired light level on the dimmer. [Diagram showing dimmer level adjustment]
2. Press and hold the "favorite" button on the remote for 6 seconds until LEDs blink twice on the in-wall dimmer. New favorite level is now saved. [Diagram showing pressing remote 'favorite' button]

Using Your Controls

In-wall dimmer:

• [ON] On / Brighter [Brighter]
• [OFF] Off / Darker [Darker]
• FASSTM (Front Accessible Service Switch) [FASST switch]

Replacing light bulbs using FASSTM: Pull the FASSTM switch out on the in-wall dimmer to remove power at the light socket.

Pico® remote control (sold separately):

• [ON] On / Brighter
• [Favorite] Favorite button
• [OFF] Darker
• [OFF] Off

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

Device Ratings

In-wall dimmer: PD-6WCL, 120 V~ 50/60 Hz

Safety & Compliance

Caution

Use only with permanently installed fixtures with dimmable LED, dimmable CFL, halogen, or incandescent lamps. To avoid overheating and possible damage to other equipment, do not use to control receptacles, motor-driven appliances, or transformer-supplied appliances.

Codes

Install in accordance with all national and local electrical codes.

Grounding

When no "grounding means" exist in the wallbox, the National Electrical Code (NEC®) allows a control to be installed as a replacement if 1) a nonmetallic, noncombustible faceplate is used with nonmetallic attachment screws or 2) the circuit is protected by a ground fault circuit interrupter (GFCI). When installing a control according to these methods, cap or remove the green wire before screwing the control into the wallbox.

FCC/IC Information

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warranty

For warranty information, please visit www.casetawireless.com/warranty.

Troubleshooting

Go to www.casetawireless.com/support for additional troubleshooting suggestions.