Caséta Wireless In-wall Dimmer PRO

Introduction

Welcome and thank you for purchasing a Caséta Wireless in-wall dimmer PRO. To control your lights from an app or remote, you will need to replace an existing switch with a Caséta Wireless in-wall dimmer PRO.

Before you install the dimmer, please watch the installation video at www.casetawireless.com/support.

We hope you enjoy the convenience of Caséta Wireless!

Double Your Warranty

Love Caséta Wireless dimmers? Have ideas for making them better? Tell us what you think and we'll extend your warranty by 1 year. Visit www.casetawireless.com/register.

Contents Supplied

• In-wall dimmer PRO (PD-10NXD)
• Wire connectors (x5)
• Screws (x2)

Tools You'll Need

• Flat-head screwdriver
• Pliers
• Phillips-head screwdriver

Installing Your Dimmer

Installation for lights with one wall switch (single pole)

1. Turn power off at circuit breaker!

   ⚠️ WARNING: SHOCK HAZARD. May result in serious injury or death. Turn off power at circuit breaker or fuse before installing.

2. Remove existing switch from wall

   Remove the wallplate from the switch. Remove the switch and pull it away from the wall. Disconnect all three wires* from the switch.

3. Remove side sections (if necessary)

   Bend back and forth. Do not remove outside side sections on dimmers at the end of a gang. Each dimmer has inside side sections removed. A dimmer in the middle has all side sections removed.

   Important note: Removing side sections reduces the dimmer's maximum wattage rating. See the chart below for maximum wattage information.

   Maximum* Wattage Derating Chart (120 V~ 50/60 Hz)

   Side sections removed	None	1 side	2 sides
   LED	250 W	250 W	250 W
   Incandescent & Halogen	1000 W	800 W	600 W
   MLV Halogen	1000 VA	800 VA	600 VA

   *For maximum wattage information when mixing light bulb types, see www.casetawireless.com/ganging.

4. Connect the dimmer

   Optional Neutral

   1. Connect the bare copper (or green) "ground" wire from the wallbox to the green wire on the dimmer using a wire connector. [?]

   2. Connect the load wire from the wallbox to the red wire on the dimmer using a wire connector.

   3. Connect the hot wire from the wallbox to the black wire on the dimmer using a wire connector.

   4. If available, connect the neutral wire from the wallbox to the white wire on the dimmer. If neutral is not available, cap the white wire with a wire connector. Neutral is required for: MLV loads, LED drivers, PHPM-PA, PHPM-3F, GRX-TVI.

   5. Cap the blue wire with a wire connector. (The blue wire is only used for a 3-way installation with a mechanical toggle switch. See Casetawireless.com/3-way for details.)

5. Mount the dimmer

   Use the screws provided. ?

6. Attach the wallplate

   Attach the adapter to the dimmer using the screws provided and snap on the wallplate. (If you installed the dimmer next to other dimmers or switches, you'll need to install a wallplate with the correct size/number of openings to accommodate all the devices.)

7. Turn power on at circuit breaker

Important Note: 3-Way Installation

If you have more than one switch controlling the light, this is called a 3-way installation. You will need to buy PJ2-WALL-WH-L01.

Please visit www.casetawireless.com/3-way for more details.

Works with Compatible Bulbs

The dimmer works with compatible energy-efficient dimmable light bulbs:

• LED*: up to 250 W
• Incandescent/Halogen: up to 1000 W
• MLV Halogen: up to 1000 VA

NOTE: You can mix and match dimmable LEDs, as well as halogen and incandescent light bulbs, with Caséta Wireless dimmers. Dimmable LED light bulbs vary in their dimming performance. If you're using these bulbs and they flicker or turn off, please visit www.casetawireless.com/lowend for information on adjusting the dimmer for best bulb performance.

*For a complete list of compatible dimmable LEDs, please visit www.casetawireless.com/bulblist.

Compatible light bulbs include: EcoSmart®, Feit®, Philips®, Sylvania® (specific models listed in original document).

Using Your Caséta Wireless Kit (Sold Separately)

With a smartphone or tablet (Bridge required, sold separately)

The Caséta Wireless dimmer can be controlled from a smartphone when used with the Lutron® Smart Bridge™. If you are using the dimmer and remote control with the Lutron® Smart Bridge™, follow the instructions below.

Note: If you are using the dimmer and remote control with another manufacturer's bridge, please refer to that manufacturer's instructions for set-up.

1. Download the Lutron® app

   Search for "Lutron Caseta" on the App Store ? or Google Play ▶️. Visit www.casetawireless.com/LutronApp.

2. Launch the Lutron® app

   The Lutron app will walk you through setting up your devices.

3. Use the Lutron® app to complete ALL remaining steps

   Add devices (Pico® remotes, Dimmers, Shades), Schedule your lights, Connect while away.

Without a smartphone or tablet (Bridge not required)

Pairing the dimmer and Pico® remote control

1. Press and hold "off" button on dimmer

   Hold for 6 seconds until LEDs start blinking. [?]

2. Press and hold "off" button on remote

   Hold for 6 seconds until lights flash 3 times. [?]

3. Press and hold "favorite" button on remote

   Hold for 6 seconds until LEDs blink twice on the in-wall dimmer. The new favorite level is now saved. [⭐]

Changing the favorite light level on the Pico® remote control (sold separately)

You can use the round "favorite" button on the Pico® remote control to recall a favorite light level. It's set to 50% by default, but you can change it to any level you like.

1. Set desired light level on dimmer

2. Press and hold "favorite" button on remote

   Hold for 6 seconds until LEDs blink twice on the in-wall dimmer. New favorite level is now saved. [⭐]

Using Your Controls

In-wall dimmer PRO

• On/Off Button: Press to turn lights on or off.
• Brighter Button: Press or hold to increase light level. [⬆️]
• Darker Button: Press or hold to decrease light level. [⬇️]
• Favorite Button: Press to recall your saved favorite light level. [⭐]

Pico® Remote Control (Sold Separately)

• On Button: Press to turn lights on.
• Brighter Button: Press or hold to increase light level. [⬆️]
• Darker Button: Press or hold to decrease light level. [⬇️]
• Off Button: Press to turn lights off. [?]
• Favorite Button: Press to recall your saved favorite light level. [⭐]

Replacing Light Bulbs Using FASSTM

Pull the FASSTM (Front Accessible Service Switch) switch out on the In-wall dimmer PRO to remove power at the light socket.

Troubleshooting

For additional troubleshooting suggestions, go to www.casetawireless.com/support.

Important Notes

• For indoor use only.
• Operate between 32 °F (0 °C) and 104 °F (40 °C).

Device Ratings

In-wall dimmer PRO PD-10NXD

120 V~ 50/60 Hz

FCC/IC Information

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Modifications not expressly approved by Lutron Electronics Co., Inc. could void the user's authority to operate this equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help.

Warranty

For warranty information, please visit www.casetawireless.com/warranty.

Trademarks

Lutron, Lutron, Caséta, and Pico are registered trademarks and FASS™, Smart Bridge are trademarks of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts. Google and the Google logo are registered trademarks of Google Inc., used with permission. ©2015 Lutron Electronics Co., Inc.

P/N 0301778 REV A