SALTO XS4 Mini ANSI with Cylindrical Latch Installation Guide

Introduction

This guide provides step-by-step instructions for installing the SALTO XS4 Mini ANSI lock, designed with a cylindrical latch. It details the installation process for both the Ci 250xx series and the Ci 270xx series, which includes override functionality. Ensure all necessary tools and components are available before proceeding.

Brand: SALTO inspiredaccess

Compatible Series: Ci 250xx series, Ci 270xx series.

Required Tools and Components

Tools:

• PH 2 Screwdriver
• TX 20 Driver

Components & Fasteners:

• Two (2) AA LR6 Batteries (SP01077-10)
• Four (4) TORX 20 self-tapping screws
• One (1) TORX 20 screw
• Two (2) TORX 20 screws
• SFIC Cylinder (Not included)

Door Preparation and Dimensions

Key Dimensions for Installation:

• Lock body: Approximately 1-35/64" (39 mm) x 1-1/16" (27 mm)
• Cylindrical Latch Backset: 4-57/64" (124.5 mm)
• Recommended Door Preparation: 3-23/64" (85 mm)
• Internal mechanism dimension: 2-1/8" (54 mm)
• Clutch/Override mechanism dimension: 1-1/8" (28.5mm)

Door Thickness Compatibility:

• For door thicknesses exceeding 2-3/8" (60 mm), specific considerations apply.
• For door thickness ranging from 1-1/4" to 1-3/8" (30-35 mm), order part number SP226233.02-BM.
• For door thickness ranging from 1-3/8" to 1-9/16" (35-40 mm), order part number SP226233.01-BM.

For detailed door preparation specifications, please refer to documents 4DS00004 or 4DS00005.

Installation - Option 1: Ci 250xx Series (Standard Cylindrical Latch)

This section outlines the installation for the SALTO XS4 Mini ANSI with a standard cylindrical latch, without override functionality.

Step 1: Prepare Inside and Outside Assemblies

Inside Assembly: Attach the spacer plate to the inside assembly. Insert the cartridge, spring, and spindle into the latch mechanism. The inside lever and cover will be secured later with a fixing screw.

Outside Assembly: Mount the outside assembly, ensuring the spindle correctly passes through the latch mechanism. The SFIC Cylinder (not included) is installed into the outside assembly.

Step 2: Select Handing

Determine and select the correct handing (L for Left, R for Right) for the lock mechanism by orienting the spindle as shown in the diagrams.

Step 3: Mount Lock Body to Door

Position the outside and inside assemblies onto the door. Use the four (4) TORX 20 self-tapping screws to securely fasten the main lock body to the door, ensuring proper alignment.

Step 4: Attach Levers and Covers

Connect the inside lever to the spindle and secure the inside cover using the fixing screw. The outside lever is also attached at this stage.

Step 5: Final Securing

Ensure all components are correctly seated and firmly attached. The installation involves aligning parts and securing them with the appropriate TORX screws.

Installation - Option 2: Ci 270xx Series (With Override)

This section details the installation process for the SALTO XS4 Mini ANSI Ci 270xx series, which features override capabilities.

Step 1: Prepare and Mount Components

Begin by preparing the inside and outside assemblies. Install the latch mechanism into the door edge and secure the strike plate to the door frame. Ensure correct Left Hand (LH) or Right Hand (RH) orientation is selected for the lock.

Step 2: Insert Control and User Keys

Insert the CONTROL KEY into its designated slot on the lock mechanism. Subsequently, insert the USER KEY into its corresponding slot.

Step 3: Assemble Lock Body and Levers

Attach the inside and outside levers, ensuring they properly engage with the spindle. Secure the main lock body and covers using the provided TORX screws.

Step 4: Verify Operation

Confirm that all parts are securely fastened and that the lock operates smoothly when using the control and user keys.

General Installation Steps

The following steps provide a comprehensive overview of the assembly process, applicable to both installation options:

Step 1: Install Latch and Strike Plate

Fit the latch mechanism into the door edge and secure the strike plate to the door frame using screws. Ensure proper alignment for smooth operation.

Step 2: Mount Outside Assembly

Attach the outside assembly to the door. The spindle must align correctly with the latch mechanism, passing through it as required.

Step 3: Mount Inside Assembly

Position the inside assembly on the interior side of the door. Align it with the outside assembly and the spindle. Secure the inside assembly using the TORX 20 screws.

Step 4: Insert Batteries

Open the battery compartment located on the inside assembly. Insert two (2) AA LR6 batteries, paying close attention to the correct polarity. A "click!" sound may indicate proper seating.

Step 5: Attach Inside Lever and Cover

Connect the inside lever to the spindle. Secure the inside cover using the fixing screw. Ensure the lever is fully seated and engages correctly.

Step 6: Secure Main Lock Body

Use the TORX 20 screws to firmly attach the main lock body to the door. The 'CTRL' screw is utilized for securing the cover in place.

Step 7: Final Lever Engagement

Confirm the inside lever is correctly attached and engages with the spindle. A "push!" action may be necessary to fully seat all components during assembly.

Step 8: Final Securing and Checks

Complete the installation by fastening all covers and ensuring all screws are appropriately tightened. Verify the lock's functionality.

Door Detector Installation (Optional Feature)

This section is relevant only for models that are equipped with a door detector feature.

Procedure:

1. Disconnect the existing connection (indicated by "Unplug" / "Débranchez" / "Desconecte").
2. Connect the door detector module (indicated by "Plug" / "Branchez" / "Conecte").

Note: A specific "Wood door detector model" is available for certain applications.

For detailed installation instructions regarding the door detector, please refer to document 225469.

Battery Change Procedure

To replace the batteries in the SALTO XS4 Mini ANSI lock:

1. Carefully remove the inside cover of the lock unit.
2. Gently unplug the battery connector from the circuit board.
3. Remove the old batteries and insert new AA LR6 batteries, ensuring they are placed with the correct polarity.
4. Reconnect the battery connector to the circuit board.
5. Reattach the inside cover securely to complete the process.

Important Notes & Disclaimers

All information presented in this guide was accurate at the time of publication. SALTO Systems S.L. reserves the right to modify the availability, design, construction, and/or materials of any product without prior notice.

Copyright © 2023 SALTO Systems S.L.