DigiTech HardWire CR-7 Stereo Chorus Owner's Manual

Declaration of Conformity

Manufacturer's Name: Harman Signal Processing

Manufacturer's Address: 8760 S. Sandy Parkway, Sandy, Utah 84070, USA

Declares that the product:

Product name: CR-7

Product option: All (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.)

Conforms to the following Product Specifications:

• Safety: IEC 60065 -01+Amd 1
• EMC: EN 55022:2006, EN 55024:1998, FCC Part 15

Supplementary Information: The product herewith complies with the requirements of the:

• Low Voltage Directive 2006/95/EC
• EMC Directive 2004/108/EC
• RoHS Directive 2002/95/EC
• WEEE Directive 2002/96/EC
• EC Regulation 278/2009

With regard to Directive 2005/32/EC and EC Regulation 1275/2008 of 17 December 2008, this product is designed, produced, and classified as Professional Audio Equipment and thus is exempt from this Directive.

With regard to the PS200R and Directive 2005/32/EC and EC Regulation 278/2009 of 6 April 2009, this regulation applies to Class A (single output) external power supplies. The PS200R used with this product is a multi-output power supply and thus is exempt from this Directive.

Signed by: Roger Johnsen, Vice-President of Engineering

Address: 8760 S. Sandy Parkway, Sandy, Utah 84070, USA

Date: October 4, 2010

European Contact: Your local DigiTech Sales and Service Office or Harman Signal Processing, 8760 South Sandy Parkway, Sandy, Utah 84070 USA. Ph: (801) 566-8800, Fax: (801) 568-7583

Safety and Disposal

Disposal Information: Do not mix this product with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. Private households in the EU, Switzerland, and Norway may return their used electronic product free of charge to designated collection facilities or retailers. For other countries, contact local authorities for correct disposal methods. This ensures necessary treatment, recovery, and recycling, preventing potential negative environmental and health effects.

Electromagnetic Compatibility: This device complies with Part 15 of the FCC Rules and the Product Specifications noted on the Declaration of Conformity. Operation is subject to the following two conditions:

• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause undesired operation.

Operation of this unit within significant electromagnetic fields should be avoided. Use only shielded interconnecting cables.

WARNING: Important Safety Instructions

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this apparatus near water.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
8. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
9. Unplug this apparatus during lightning storms or when unused for long periods of time.
10. No user-serviceable parts inside. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
11. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
12. Refer to labels on the unit, including the bottom cover, for other markings and pertinent information.

Warranty Information

DigiTech is proud of its products and backs each one with the following warranty:

1. Please register online at www.digitech.com within ten days of purchase to validate this warranty. This warranty is valid only in the United States.
2. DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. This warranty is valid to the original purchaser only and is non-transferable.
3. DigiTech liability under this warranty is limited to repairing or replacing defective materials that show evidence of defect, provided the product is returned to DigiTech WITH RETURN AUTHORIZATION. All parts and labor will be covered up to a period of one year. This warranty is extended to a period of six years when the product has been properly registered through the website. A Return Authorization number may be obtained from DigiTech by telephone. The company shall not be liable for any consequential damage as a result of the product's use in any circuit or assembly.
4. Proof-of-purchase is considered the responsibility of the consumer. A copy of the original purchase receipt must be provided for any warranty service.
5. DigiTech reserves the right to make changes in design, or make additions to, or improvements upon this product without incurring any obligation to install the same on products previously manufactured.
6. The consumer forfeits the benefits of this warranty if the product's main assembly is opened and tampered with by anyone other than a certified DigiTech technician, or if the product is used with AC voltages outside of the range suggested by the manufacturer.
7. The foregoing is in lieu of all other warranties, expressed or implied. DigiTech neither assumes nor authorizes any person to assume any obligation or liability in connection with the sale of this product. In no event shall DigiTech or its dealers be liable for special or consequential damages or from any delay in the performance of this warranty due to causes beyond their control.

NOTE: The information contained in this manual is subject to change at any time without notification. Some information may also be inaccurate due to undocumented changes in the product or operating system since this version of the manual was completed. The information contained in this version of the owner's manual supersedes all previous versions.

Welcome and Introduction

Congratulations! You have just purchased a DigiTech digital effect pedal.

Unlike many analog pedals, the number of hours digital pedals can be powered with 9-Volt alkaline batteries is limited due to the constant draw which digital signal processors require. Until battery technology advances to meet the requirements of digital pedals, it is suggested that a battery be used mainly for demonstration and practice purposes.

If you notice a change in the LED's brightness, or the pedal will not switch from Bypass to Effect, replace the battery with a new 9-Volt alkaline battery or visit your local DigiTech dealer to obtain a power adapter and unleash the pedal's full potential with unlimited power.

Introduction

More than a remarkable achievement, DigiTech's HardWire series represents a collection of significant improvements in guitar effects pedals. The HardWire series pedals provide a suite of well-known effects, each with superior tone and control. These pedals go above and beyond their peers to provide distinguishing features like true bypass and high voltage operation, making them essential additions to the signal chain of players who value sound quality and demand the utmost in performance.

Included Items

• HardWire CR-7 Stereo Chorus
• StompLock™
• Foot Switch Glow Sticker
• Hook-and-loop Pedalboard Pad
• Online Warranty Registration Information Card

Pedal Interface and Controls

The DigiTech HardWire CR-7 Stereo Chorus features the following controls and connections:

• 1. Level Knob: Controls the chorus level. Turn clockwise to increase, counter-clockwise to decrease.
• 2. DC Adapter Jack: Connect the optional Harman power supply here. Use the proper supply for your area's mains line voltage.
• 3. Speed Knob: Controls the modulation speed of the chorus effect. Turn clockwise to increase speed, counter-clockwise to decrease speed.
• 4. Depth Knob: Controls the intensity of the chorus effect. Turn clockwise for a deep, rich chorus sound; counter-clockwise for a subtle chorusing.
• 5. Type Knob: Selects one of seven chorus types:
  • STUDIO: Studio quality chorus with a wide stereo image.
  • MULTI: True 8-voice chorus; the lushest chorusing available in a pedal.
  • MODERN: Dual voice chorusing that is both very rich and smooth.
  • BOUTIQUE: A rich chorus with the quirkiness of analog circuits.
  • ANALOG: Distinctively organic bucket-brigade chorus.
  • JAZZ: Single voice chorusing with a dry output.
  • VINTAGE: Warm and versatile, from subtle to euphoric.
• 6. Input 1 (Mono): Connect your instrument, an additional pedal, or an amp effects send to this jack. Signals are heard at both outputs when only Input 1 (Mono) is used. This jack enables battery power to the pedal when connected. To prolong battery life, disconnect the cable from this jack when not in use. If the optional Harman power supply is used, cables can remain connected.
• 7. Input 2: Connect a second input to this jack for stereo operation. Inputs 1 and 2 are processed separately through the stereo chorus effect and then fed to Outputs 1 and 2, maintaining true stereo separation between channels.
• 8. Foot Switch Release Pins: These two spring-loaded pins hold the Foot Switch in place. They are used to access and change the battery.
• 9. Indicator LED: Lights when the effect is turned on. When battery power is low (approximately 15 minutes before depletion), the Indicator LED dims, providing an advanced warning that the battery needs replacement soon.
• 10. Foot Switch: Turns the effect on and off.
• 11. Output 1 (Mono): Connect this output to the input of a single guitar amplifier, another pedal input, or an amp effects return.
• 12. Output 2: Connect this output to a second guitar amplifier when two amplifiers are being used.

NOTE: Use unbalanced mono instrument cables only.

Setup Diagrams

Amp Setup

This setup involves connecting your guitar to the pedal's input and the pedal's output to a single amplifier. An optional Harman Power Supply can be used for power. An alternative shows the pedal placed within an amplifier's effects loop.

Effects Loop Setup

For stereo operation or integration into an amp's effects loop, connect your guitar to Input 1. Output 1 connects to the amplifier's effects SEND, and the amplifier's effects RETURN connects to Input 2. An optional Harman Power Supply can be used. If the amp effects loop has a mix control, set the mix to 100% full wet.

Battery Operation

In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass, eliminating the need to remove the pedal from your pedal chain. To replace the battery:

1. Using the tip of a 1/4" guitar cable, push in one of the Release Pins on either side of the Foot Switch and remove it from the pedal chassis.
2. Remove the battery from the battery compartment and disconnect the battery cable.
3. Connect a new battery to the battery cable and place it back in the battery compartment. Ensure the battery cable does not interfere with the spring or pedal switch arm.
4. Place one hole of the Foot Switch over its corresponding pin.
5. Push the opposite pin in and lower the other side of the Foot Switch into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both Release Pins should be flush with the outer side of the pedal.

The diagram illustrates the pedal chassis components: Foot Switch, Pedal Switch Arm, 9VDC Battery, Battery Compartment, Spring, and Foot Switch Release Pins. The Foot Switch is shown being removed.

Performance Accessories

The following accessories are included to enhance your pedalboard integration:

• Hook-and-loop Pedalboard Pad: Designed to attach to the surfaces found on most commercial pedal boards. To apply, peel off the existing rubber skid pad from the bottom of the pedal, peel the adhesive protector from the back of the Pedalboard Pad, and apply the pad to the bottom of the pedal.
• Foot Switch Glow Sticker: Easily visible on dark stages. To apply, peel the adhesive backing from the sticker and apply it to the top of the Foot Switch.
• StompLock™: Keeps your settings where you want them. To place the StompLock over the pedal knobs, set the knobs to your preferred setting, gently push the StompLock over the top of the knobs. To remove, gently lift one side and then the other.

Specifications

*Recommended power saving GreenEdge power supply models.

Contact and Support

For further information, please visit the DigiTech website:

www.digitech.com

DigiTech
8760 South Sandy Parkway
Sandy, Utah 84070
PH (801) 566-8800
FAX (801) 566-7005

DigiTech® and HardWire® are registered trademarks of Harman. Designed in the USA.

Copyright - Harman. Printed in China.

HardWire CR-7 Owners Manual 5024335-B