D-Link DSS-200G-10MP PoE Switch

Quick Installation Guide

Package Contents

One DSS-200G-10MP switch
One AC power cord
One Quick Installation Guide

Note: The model purchased may appear slightly different from illustrations.

Device Interfaces

Port	Description
10/100/1000Base-T PoE ports	8 x 10/100/1000Base-T PoE ports (10/100/1000 Mbps connection speed).
1000Base-X SFP ports	2 x 1000Base-X SFP ports (100/1000 Mbps connection speed).
RJ-45 Alarm port	RJ-45 Alarm port for connecting external alarm devices.

LEDs

LED	Status	Description
Power	Solid green	The switch is powered on.
	Light off	The switch is powered off.
Alert	Solid red	The alarm is triggered. Switch will send out traps and logs when an error event occurs.
PoE Mode/Link Mode	Solid amber	LEDs for ports 1-8 are in PoE Mode (PoE OK/PoE Fail).
	Solid green	LEDs for ports 1-8 are in Link Mode (Link/Activity/Speed).
Link/Activity/Speed (per port 1-8)	Solid green	There is a secure 1000 Mbps connection at the port.
	Blinking green	There is reception or transmission occurring at the port.
	Solid amber	There is a secure 10/100 Mbps connection at the port.
	Blinking amber	There is reception or transmission occurring at the port.
	Light off	No link.
Link/Activity/Speed (per port 9-10)	Solid green	There is a secure 1000 Mbps connection at the port.
	Blinking green	There is reception or transmission occurring at the port.
	Solid amber	There is a secure 100 Mbps connection at the port.
	Blinking amber	There is reception or transmission occurring at the port.
	Light off	No link.
PoE OK/PoE Fail (per PoE port)	Solid green	PD device insert and power feeding.
	Solid amber	PD device insert but failure occurs.
	Light off	No PD device insert.

PoE Power Budget

100% LED: Solid red - PoE power has reached 100%.
75% LED: Solid amber - PoE power ≤ 75%.
50% LED: Solid green - PoE power ≤ 50%.
25% LED: Solid green - PoE power ≤ 25%.

Installation Guidelines

Follow these guidelines for proper and safe installation.

Visually inspect the power cord for secure connection to the AC power connector.
Ensure proper heat dissipation and adequate ventilation around the switch.
Do not place heavy objects on the switch.

Desktop or Shelf Installation

Attach the rubber feet to the bottom corners of the device's base. Ensure sufficient ventilation space between the device and surrounding objects.

[Diagram: Rubber feet attached to the bottom of the switch]

Rack Installation

Mount the switch in a standard 19-inch EIA rack. Attach the mounting brackets to the switch's side panels and secure them with screws. Then, use rack screws to mount the switch into the rack.

[Diagram: Mounting brackets attached to the switch side panels]

[Diagram: Switch installed in a rack]

Installing Transceivers into the Transceiver Ports

The DSS-200G-10MP is equipped with ports for connecting SFP transceivers.

[Diagram: Inserting SFP transceivers into the SFP ports]

Grounding the Switch

This procedure must be completed before powering on the switch.

Required Tools and Equipment:

Ground screw: One M4 x 6 mm (metric) pan-head screw.
Grounding cable (not included): Cable must meet local/national requirements. A 12 to 6 AWG copper conductor is recommended. Length depends on proximity to grounding facilities.
Screwdriver (not included).

Grounding Steps:

Verify the switch power is off.
Attach the terminal lug ring of the grounding cable to the switch's ground screw opening using the ground screw.
Attach the other end of the grounding cable's terminal lug ring to an appropriate grounding stud or bolt on the rack.
Verify that connections at the switch's ground connector and the rack are secure.

Plugging in the AC Power Cord

Connect one end of the AC power cord to the switch's power socket and the other end to a grounded and surge-protected electrical outlet.

Power Failure

In case of a power failure, unplug the power cord from the switch as a precaution. After power is restored, plug the cord back in.

Technical Specifications

Hardware

Processor	500 MHz
RAM	128 MB
Flash Memory	32 MB
Interfaces	8 x 10/100/1000Base-T PoE ports, 2 x 1000Base-X SFP ports, RJ-45 Alarm port
Indicators	Power, Alert, PoE Mode/Link Mode, Link/Activity/Speed (per port), PoE OK/PoE Fail (per PoE port), PoE Power Budget
DIP Switches	5 DIP switches: QoS, Extend, Isolate, PD-Alive, STP
Buttons	Reset Button, Mode Button
Power Connector	AC power input connector

Functionality

IEEE 802.3 10Base-T
IEEE 802.3u 100Base-TX
IEEE 802.3ab 1000Base-T
IEEE 802.3z 1000Base-X
IEEE 802.3az Energy-Efficient Ethernet
Automatic speed and duplex mode negotiation
Flow control IEEE 802.3x in full-duplex mode
Auto-negotiation or manual MDI/MDIX detection on all copper ports

Performance

Switching Fabric	20 Gbps
Forwarding Method	Store-and-forward
MAC Address Table Size	8K entries
Max. Packet Forwarding Rate (64-byte packets)	14.88 Mpps
Packet Buffer	512 KB
Jumbo Frame	10,000 bytes

PoE

PoE Standard	IEEE 802.3af, IEEE 802.3at
PoE Ports	Ports 1-8
PoE Power Budget	130 W (max. 30 W per PoE port)

Physical Parameters

Dimensions (L x W x H)	280 x 180 x 44 mm
Weight	1.55 kg

Operating Conditions

Power	100 to 240 VAC, 50/60 Hz
Max. Power Consumption	160.2 W (PoE enabled), 9.63 W (PoE disabled)
Power Consumption in Standby	9.53 W
Heat Dissipation	30.18 W (103.05 BTU/hr)
MTBF (hours)	345,045
Noise Level	0 dB
ESD Protection	Supports up to 6 kV on copper ports (IEC61000-4-5)
Ventilation System	Passive
Temperature	Operating: -5 to 50 °C, Storage: -40 to 70 °C
Humidity	Operating: 0% to 95% non-condensing, Storage: 0% to 95% non-condensing

Other

Safety	cUL, UL, LVD, CB, BSMI
EMI	FCC/IC, CE, BSMI

Technical Support

Software updates and documentation are available on the D-Link website. D-Link provides free support during the warranty period. Customers can contact the D-Link technical support group via phone or the Internet.

D-Link technical support operates 24/7, daily, except for official holidays. Calls are free within Russia.

D-Link Technical Support:
8-800-700-5465

Technical Support via Internet:
Website: http://www.dlink.ru
Email: support@dlink.ru

Manufacturer:
D-Link Corporation, 11494, Taipei, Neihu District, Sintsu 3-Road, No. 289, Taiwan.

Authorized Representative, Importer:
LLC "D-Link Trade"
390043, Ryazan, pr. Shabulina, d.16
Tel: +7 (4912) 575-305

Russian Office Address:
Moscow, Grafsky pereulok, 14
Tel: +7 (495) 744-00-99
Email: mail@dlink.ru

Version 1.0 2023-03-13

	D-Link DGS-1210-52MP/FL Managed L2 Gigabit PoE Switch Overview A comprehensive overview of the D-Link DGS-1210-52MP/FL, a 48-port managed Layer 2 Gigabit Ethernet switch featuring PoE, advanced security, robust Layer 2/3 functionalities, and energy-efficient operation, including technical specifications and SFP compatibility.
	D-Link DGS-1026MP Gigabit PoE Switch: Features and Specifications Detailed information on the D-Link DGS-1026MP, a 24-port Gigabit PoE switch with 2 combo SFP ports. Features include IEEE 802.3af/at PoE support, 370W PoE budget, Plug-and-play installation, and energy efficiency.
	D-Link DGS-F1210-18PS-E: Layer 2 Gigabit Managed Long Range PoE+ Surveillance Switch Comprehensive overview of the D-Link DGS-F1210-18PS-E, an 18-port Layer 2 Gigabit Managed Long Range PoE+ Surveillance Switch. Features 16 10/100/1000 Mbps PoE ports and 2 Gigabit SFP uplink ports, supporting IEEE 802.3af/at PoE and extended transmission distances up to 250m.
	D-Link DGS-3000-10L Quick Installation Guide Quick installation guide for the D-Link DGS-3000-10L L2 Managed Switch, covering package contents, hardware installation, power connection, redundant power supply, management options, and technical specifications.
	D-Link DES-1009MP Quick Installation Guide Step-by-step instructions for setting up the D-Link DES-1009MP 9-port 10/100 PoE Switch, including hardware overview, installation, technical specifications, and support information.
	D-Link DIS-200G Series Industrial Ethernet Switch Quick Installation Guide This guide provides step-by-step instructions for setting up the D-Link DIS-200G Series Layer 2 Gigabit Industrial Smart Managed Switch. It covers hardware overview, installation methods (DIN rail, wall, rack), power connection, grounding, and management options via Web UI, DNA, Console, Telnet, and SNMP.
	D-Link DMS-1250-10SP L2 Smart Managed Switch Quick Installation Guide Quick start guide for the D-Link DMS-1250-10SP, an L2 Smart Managed Switch. Details package contents, device interfaces, LED indicators, installation steps (desktop and rack-mount), management options (CLI, SNMP, Web UI), and technical specifications. Includes setup procedures for console and web interfaces.
	D-Link DMS-1250-10SPL Quick Installation Guide A comprehensive guide for the D-Link DMS-1250-10SPL L2 Smart Managed Switch, detailing package contents, device interfaces, LED indicators, installation procedures, management options, technical specifications, and support information.