Triple Monitor Desk Mount

⚠️ WARNING

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact VIVO product support at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Failure to report missing parts within 30 days may result in denial of free replacement. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

⚠️ WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY

FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• DO NOT EXTEND ARMS TOO FAR FORWARD OR BACKWARD
• NEVER ALLOW CHILDREN TO CLIMB, STAND, OR PLAY ON ANY PART OF MONITOR MOUNT
• USE TIPOVER RESTRAINT TO REDUCE (BUT NOT ELIMINATE) RISK OF TIPOVER

ALWAYS EXERCISE CAUTION WHEN ADJUSTING THE PLACEMENT OF YOUR MONITORS.

Need Help? We're Here For You

US-Based Customer Support from Trained Professionals

Monday-Friday from 7am-7pm CST
Saturday 8am-4pm CST

Assembly Video & Product Info: www.vivo-us.com/products/stand-v300g

Package Contents

• A (x1) Pole: The main vertical support.
• B (x1) Arm Bracket: Connects arms to the pole.
• C (x1) Clamp: Attaches the mount to a desk edge.
• D (x2) Shaft Collar: Secures components on the pole.
• E (x2) VESA Arm: Pneumatic arms for side monitors.
• F (x4) Arm Extension: Connects VESA arms to the main bracket.
• G (x1) VESA Plate: Mounts to the monitor's VESA holes.
• H (x6) Plastic Cover: Decorative covers for arm joints.
• I (x2) Cable Clip: For cable management.

Included Hardware & Tools

Hardware

• M-A (x12) M4x12mm Screw
• M-B (x12) M4x30mm Screw
• M-C (x12) M4x8mm Screw
• M-D (x12) Spacer: Used with screws for monitor mounting.

Tools

• T-A (x1) 3mm Allen Wrench
• T-B (x1) 5mm Allen Wrench

Tools Needed:

• Phillips Screwdriver

Weight Capacity:

17.6 lbs (8 kg) Per Arm

Assembly Steps

STEP 1: Attach Clamp to Pole

Thread Pole (A) onto Clamp (C). Place the clamp onto the edge of your desktop and tighten both Clamp Bolts (C1) to secure.

Secure the Pole by tightening the set screw on the back of the Clamp using the 3mm Allen Wrench (T-A).

STEP 2: Attach Arm Bracket to Pole

Slide Shaft Collar (D) onto Pole (A) and secure by tightening its handle. Slide the Arm Bracket (B) onto the Pole so that it rests on the Shaft Collar. Secure the Arm Bracket by tightening the back screw using the 5mm Allen Wrench (T-B).

STEP 3: Attach Arm Extensions and Second Shaft Collar

Place two Arm Extensions (F) on both sides of the Arm Bracket (B) as shown. Secure each Arm Extension by tightening its set screw on the back using the 3mm Allen Wrench (T-A). Slide another Shaft Collar (D) onto Pole (A) and secure by tightening its handle.

STEP 4: Attach VESA Plate to Center Monitor

Attach the VESA Plate (G) to your center monitor using the appropriate Screws (M-A, M-B, or M-C). Spacers (M-D) may be used if necessary to ensure a secure fit. The diagram shows correct screw lengths; avoid screws that are 'Too Long' or 'Too Short'.

STEP 5: Attach VESA Arms to Side Monitors

Attach the VESA Arms (E) to your side monitors using the appropriate Screws (M-A, M-B, or M-C). Spacers (M-D) may be used if necessary. The diagram shows correct screw lengths; avoid screws that are 'Too Long' or 'Too Short'.

STEP 6: Mount Monitors to Arms

Place monitors with VESA Arms (E) onto the Arm Extensions (F). Slide the center monitor with VESA Plate (G) onto the Pole (A). Secure by tightening the set screws on the VESA Arms and VESA Plate using the 3mm Allen Wrench (T-A).

STEP 7: Install Plastic Covers

Insert the Plastic Covers (H) into the designated slots on the VESA Arms (E) and Arm Extensions (F).

STEP 8: Manage Cables

Attach Cable Clips (I) to the Pole (A). Manage your monitor and power cables using the Cable Clips and the built-in channels, ensuring enough slack is left to allow for full adjustment of the arms.

Adjustments

STEP 9: Adjusting Side Monitor Height (Tension)

1. Position Mount Arm: Position the arm horizontally, as shown, and firmly hold it in place.
2. Insert Allen Wrench: Insert the 5mm Allen Wrench (T-B) into the adjustment screw located on the back of the monitor arm.
3. Set Monitor Height: Turn the 5mm Allen Wrench (T-B) 10-20 times to obtain proper support for your monitor. Use the guide below to adjust the tension according to the amount of counterbalance needed to support the monitor.

Tension Adjustment Guide

Note: Requires 10-20 Turns

Vertical Tilt Adjustment

To adjust the vertical tilt, loosen the side screw behind the monitor using the 5mm Allen Wrench (T-B), adjust to your desired angle, and retighten.

Horizontal Tilt Adjustment

To adjust the horizontal tilt, loosen the top screw behind the monitor using the 5mm Allen Wrench (T-B), adjust to your desired angle, and retighten.

Love Your New Setup? Tag Us on Social!

Follow VIVO on social media:

• Facebook: @VIVO-us
• Instagram: @vivo_us
• YouTube: @VIVOus
• LinkedIn: VIVO

For more great VIVO products, check out our website at: www.vivo-us.com

Last Updated: 01/07/25, REV3, v1.0