VIVO Triple Monitor Desk Mount

Important Safety Information

⚠️ WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

⚠️ TIPOVER WARNING

Serious or fatal crushing injuries can occur from tipover. To help prevent tipover:

• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD OR BACKWARD.
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF THE MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

Use of tipover restraints may only reduce, but not eliminate, the risk of tipover.

⚠️ WARNING: CHOKING HAZARD

Small parts - not for children under 3 years. Adult supervision is required.

Package Contents

• A (x1) Pole
• B (x1) Arm Bracket
• C (x1) Clamp
• D (x2) Shaft Collar
• E (x2) Monitor Arm
• F (x4) Arm Extension
• G (x1) VESA Plate
• H (x6) Plastic Cover
• I (x2) Cable Clip
• M-A (x12) M4x12 Screw
• M-B (x12) M4x30 Screw
• M-C (x12) M4x8 Screw
• M-D (x12) Spacer
• T-A (x1) 3mm Allen Wrench
• T-B (x1) 5mm Allen Wrench

The package contents are illustrated with small line drawings of each part, labeled with its letter and quantity.

Tools Needed

• Phillips Screwdriver

The tools needed section shows an icon of a Phillips screwdriver.

NOTE: Some hardware included may not be used.

DO NOT EXCEED WEIGHT CAPACITY.

Maximum weight capacity per arm: 17.6 lbs (8kg).

Failure to do so may result in serious injury.

Assembly Steps

STEP 1

Thread Pole (A) onto Clamp (C). Tighten the set screw in the back of Clamp (C) with 3mm Allen Wrench (T-A) to secure Pole (A) in place.

Illustration depicts Pole (A) being threaded into the top of Clamp (C). A set screw located on the rear of Clamp (C) is shown being tightened with the 3mm Allen Wrench (T-A).

STEP 2

Slide Shaft Collar (D) onto Pole (A). Tighten the handle on Shaft Collar (D) to secure it in place. Slide Arm Bracket (B) onto Pole (A) so that it rests on Shaft Collar (D). Tighten the screw in the back of Arm Bracket (B) with 5mm Allen Wrench (T-B).

Illustration shows Shaft Collar (D) being slid onto Pole (A) and its handle tightened. Arm Bracket (B) is then shown sliding onto Pole (A) to rest on the collar. A screw on the back of the bracket is shown being tightened with the 5mm Allen Wrench (T-B).

STEP 3

Place an Arm Extension (F) on either side of Arm Bracket (B). Attach the second set of Arm Extensions (F) to the first set. Tighten the set screws in the back of Arm Extensions (F) using 3mm Allen Wrench (T-A). Slide Shaft Collar (D) onto Pole (A). Tighten the handle on Shaft Collar (D) to secure it in place.

Illustration shows Arm Extensions (F) being attached to Arm Bracket (B). Another diagram shows Shaft Collar (D) being slid onto Pole (A) and tightened.

STEP 4: Mounting Monitor Arm to Monitor

OPTION A: Flat Back Monitor

Mount Monitor Arm (E) to your monitor using M4x8 Screws (M-C) or M4x12 Screws (M-A).

NOTE: Hand tighten screws to avoid stripping the plastic screw heads.

Illustration shows Monitor Arm (E) being attached to a flat-back monitor using screws. Icons indicate the types of screws (M-C, M-A) and show a checkmark for correct attachment and a cross for incorrect. A warning symbol is present.

OPTION B: Curved Back Monitor

Mount Monitor Arm (E) to your monitor using M4x30 Screws (M-B) with Spacers (M-D).

Illustration shows Monitor Arm (E) being attached to a curved-back monitor using screws (M-B) and Spacers (M-D). Icons indicate the types of screws and spacers, and show a checkmark for correct attachment and a cross for incorrect.

STEP 5: Mount VESA Plate

Mount VESA Plate (G) to your monitor using M4x8 Screws (M-C) or M4x12 Screws (M-A) or M4x30 Screws (M-B). If necessary, Spacers (M-D) may be used.

Illustration shows VESA Plate (G) being attached to a monitor. Two options are presented: one using screws (M-C or M-A) and another using screws (M-B) with Spacers (M-D). Icons indicate screw types and the option of using spacers.

STEP 6

Mount Monitor Arms (E) onto Arm Extensions (F). Slide VESA Plate (G) onto Pole (A). Tighten set screws in the back of Monitor Arms (E) and VESA Plate (G) using 3mm Allen Wrench (T-A).

Illustration shows Monitor Arms (E) being attached to Arm Extensions (F). VESA Plate (G) is shown sliding onto Pole (A). An inset shows tightening set screws with the 3mm Allen Wrench (T-A).

STEP 7

Insert Plastic Covers (H) into Monitor Arms (E) and Arm Extensions (F). Adjust the tilt of Monitor Arms (E) and VESA Plate (G) using 5mm Allen Wrench (T-B). The tension of Monitor Arms (E) can be adjusted using 5mm Allen Wrench (T-B).

Illustration shows Plastic Covers (H) being inserted into the arms. An inset labeled "VESA Tilt Adjustment" shows the use of the 5mm Allen Wrench (T-B) for tilt adjustment. Another inset shows the use of the 5mm Allen Wrench (T-B) for adjusting arm tension.

STEP 8

Attach Cable Clips (I) to Pole (A). Manage monitor cables into cable covers on the underside of Monitor Arms (E), Arm Extensions (F), and Cable Clips (I). Leave enough slack to allow full adjustment and motion of arms.

Illustration shows Cable Clips (I) being attached to Pole (A). Cables are depicted being routed through the clips and along the arms. An inset provides a closer view of cable management.

Support and Contact Information

Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us

LAST UPDATED: 02/16/2023 REV1

VIVO's dedicated support team offers immediate assistance with rapid response times. If any parts are received damaged or defective, please contact VIVO. They are happy to replace parts to ensure you have a fully functioning product.

Support Hours: Monday - Friday 7:00am - 7:00pm CST

For more VIVO products, check out our website at: www.vivo-us.com