VIVO Quad Monitor Desk Mount

Important Safety Information

⚠️ WARNING!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

⚠️ TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

⚠️ WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Maximum Weight Capacity: 22 lbs (10 kg) PER ARM

DO NOT EXCEED WEIGHT CAPACITY. Failure to do so may result in serious injury.

Tools Needed

• Phillips Screwdriver ?
• Drill ड्रिल

Package Contents

NOTE: Some hardware included may not be used.

Assembly Steps

STEP 1 - Clamp Installation

Install Pole (A) to Clamp Brace (C) using M6x10mm Screws (S-C) and a Phillips screwdriver.

Diagram Description: A pole (A) is shown being attached to a clamp brace (C) with screws (S-C).

Assemble Clamp (B) to Clamp Brace (C) using M10x15mm Screws (S-D) and 6mm Allen Wrench (T-B). Secure the clamp assembly to the desktop by tightening the hand bolts on Clamp (B). Install the Pole Cover (D) to Pole (A).

Diagram Description: The clamp assembly (B attached to C) is shown being secured to a desktop. A pole cover (D) is being placed onto the pole (A). Screws (S-D) and wrench (T-B) are indicated.

STEP 1 - Grommet Installation

Remove adhesive backing from Foam Pad (I) and place on the bottom of Pole (A).

Diagram Description: A foam pad (I) is shown being applied to the bottom of the pole (A).

Install Pole (A) to an existing grommet hole using Support Plate (H) with M10x100mm Screw (S-B), M10 Washer (S-I), and Spring Washer (S-H). Tighten with Wrench (T-D). Install the Pole Cover (D) to Pole (A).

Diagram Description: The pole (A) is shown being inserted through a desk grommet hole. From underneath, a support plate (H), screw (S-B), washer (S-I), and spring washer (S-H) are used to secure it, tightened with wrench (T-D). A pole cover (D) is added.

If no grommet hole exists, drill a 3/8” (10mm) diameter hole through the mounting surface.

STEP 2

Lay Monitor Arm (F) on a flat surface with holes for cable clips facing down. Add Plastic Spacers (L) to holes at the ends of Monitor Arm (F).

Diagram Description: Monitor arms (F) are laid flat, with plastic spacers (L) being inserted into holes at their ends. Cable clip holes are indicated as being on the underside.

Align Monitor Arms (F) and Center Monitor Arm (E,F) so that the holes for the cable clips are facing down. Insert Monitor Arms (F) into Center Monitor Arm (F) as shown. Secure using M10x47mm Screws (S-A) and 6mm Allen Wrench (T-C).

Diagram Description: Two monitor arms (F) are being attached to a central arm (E or F) using screws (S-A) and wrench (T-C). Cable clip holes are noted as being on the underside.

Press Monitor Arm Covers (J) onto the top and bottom of arm joints. Place Cable Clips (M) into wire clip holes.

Diagram Description: Monitor arm covers (J) are being fitted onto the joints of the arms. Cable clips (M) are being inserted into designated holes.

STEP 3

Slide the arm assembly onto Pole (A) at the desired height and secure using M8x10mm Screws (S-E) and 5mm Allen Wrench (T-B).

Diagram Description: The assembled monitor arm structure is shown sliding onto the pole (A) and being secured with screws (S-E) and wrench (T-B).

STEP 4a - Flat Back Monitors

Attach the Center VESA Plates (P) to the monitors intended for the center of the mount. Attach Side VESA Plates (O) to remaining monitors. Secure using M4x12mm Screws (M-A).

Diagram Description: Two diagrams show VESA plate installation. The left shows a Center VESA Plate (P) attached to a monitor back with screws (M-A). The right shows a Side VESA Plate (O) attached to a monitor back with screws (M-A).

NOTE: Hand tighten screws to avoid stripping the plastic screw heads.

STEP 4b - Curved/Recessed Back Monitors

Attach the Center VESA Plates (O) to the monitors intended for the center of the mount. Attach Side VESA Plates (N) to remaining monitors. Secure using M4 Spacers (M-C), M4x30mm Screws (M-B), and a Phillips screwdriver.

Diagram Description: Two diagrams show VESA plate installation for curved/recessed backs. The left shows a Center VESA Plate (O) attached to a monitor back with spacers (M-C) and screws (M-B). The right shows a Side VESA Plate (N) attached similarly.

STEP 5

Slide the center monitors onto the Center Head (E1) and Mount (G). Install M4x6mm Screws (S-G) to secure the monitors.

Diagram Description: Monitors are shown being attached to the central mounting points (E1 and G) using screws (S-G).

STEP 6

Slide the outer monitors onto Outer VESA Heads (F1). Secure with Cap Nut (S-F).

Diagram Description: Monitors are shown being attached to the outer mounting points (F1) and secured with a nut (S-F).

Adjust Monitor Tilt

Pry off Plastic Covers (F2) from the Outer VESA Heads (F1). The exposed nut on the side is used to adjust the tilt. Tighten the nut using Wrench (T-D) to adjust. Replace Plastic Covers (F2).

Diagram Description: Plastic covers (F2) are removed from the outer VESA heads (F1) to access a nut for tilt adjustment, using wrench (T-D).

To adjust center monitor swivel or tilt, use 3mm Allen Wrench (T-A) to loosen the center set screw on the Center Head (E1) and Mount (G), as shown.

Diagram Description: A set screw on the central mount (E1/G) is shown being loosened with an Allen wrench (T-A) for swivel/tilt adjustment.

Adjust Monitor Height

To adjust center monitor height, turn the screw behind Center Head (E1) and Mount (G) using the 5mm Allen Wrench (T-B).

Diagram Description: A screw behind the central mount (E1/G) is shown being turned with an Allen wrench (T-B) to adjust monitor height.

Level Side Monitors

To level the side monitors, remove the Cap Nut (S-F) and turn the inner bolt with the 3mm Allen Wrench (T-A) to raise or lower the monitor. Replace Nut after the adjustment.

Diagram Description: A nut (S-F) is removed from a side arm to access a bolt for leveling the monitor, adjusted with wrench (T-A).

Adjust Swivel Joint Tension

To adjust swivel joint tension, remove the Monitor Arm Cover (J) and turn the bolt underneath with the 6mm Allen Wrench (T-C).

Diagram Description: A monitor arm cover (J) is removed to access a bolt for adjusting swivel tension, using wrench (T-C).

Cable Management

Manage cables using Cable Clips (M) on assembled arms. Remove the split cap from the Pole (A) and feed cables through, pulling ends out from the opening in back. Replace the split cap when finished.

Diagram Description: Cable clips (M) are shown on the arms. A split cap on the pole (A) is removed to feed cables through.