Allen + Roth 36-Inch Vanity with Top

Product Overview

This document provides instructions for the installation, care, and maintenance of the Allen + Roth 36-inch vanity with top. It also includes a parts list and warranty information.

The Allen + Roth logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.

For Spanish instructions, see page 11.

Attach Your Receipt Here

Serial Number: _________________________ Purchase Date: _________________________

Customer Service

For questions, problems, or missing parts, please contact the customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday. You can also contact them at partsplus@lowes.com or visit www.lowespartsplus.com.

Parts Included:

Diagram shows a vanity with parts labeled A through H.

Hardware Contents:

AA - Touch Up Pen (Qty. 1)

Diagram shows a touch-up pen.

Please read and understand this entire manual before attempting to assemble, operate or install the product.

WARNING

• There are several assembly steps, including unpacking, that require two adults.

CAUTION

• DO NOT try to pry off the top from the vanity, as damage to the top or vanity may occur.
• Follow these instructions closely, take your time, and use care while assembling this vanity.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Before beginning assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated Installation Time: 45 minutes (24 hours for silicone caulk to dry).

Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with drill bit.

Helpful Tools (not included): Measuring tape, level.

Step 1: Prepare the Top

Remove the top (B) from the vanity (A). Place the top (B) and backsplash (C) face down onto a scratch-free surface such as a foam sheet that came in the packaging.

Diagram shows the top (B) and backsplash (C) being removed from the vanity (A) and placed face down.

Step 2: Position and Secure the Vanity

Clean the area where the vanity (A) will be permanently located prior to installation, ensuring it will not interfere with any water supply and drain lines once mounted.

With two people, carefully place the vanity (A) against the wall in its final location. While holding the vanity base firmly against the wall, use the pre-assembled levelers on the bottom of each leg to level the item. Twisting the levelers counterclockwise will raise the height, and clockwise will lower it.

Once the vanity is in place, against the wall, and level, drill a hole through the vanity mounting area and into the wall studs. Using appropriate mounting hardware (not included), secure the vanity (A) to a wall stud. If possible, secure to two wall studs for increased stability.

WARNING: Vanity (A) MUST be secured to the wall.

Diagram shows the vanity being leveled against the wall and secured to wall studs.

Note: It may be easier to install the faucet and drain kit (not included) to the top (B) per the manufacturer's instructions before proceeding to Step 3.

Step 3: Attach the Top

Apply stain-free silicone caulk (not included) to the top edge of the vanity (A). With the help of another adult, gently lower the top (B) onto the vanity (A). Wipe away any excess caulk with a soft cloth and wait approximately 24 hours for it to dry.

Diagram shows silicone caulk being applied to the vanity top edge, and the top being lowered onto the vanity.

Step 4: Attach the Backsplash

Apply silicone caulk (not included) to the unpolished side and bottom of the backsplash (C). Position the backsplash (C) on top (B) and against the wall. Clean any excess caulk before allowing it to dry.

Diagram shows the backsplash being attached to the top and wall with caulk.

Step 5: Install Plumbing Access Lid

The back of the vanity is open for accessibility for drain(s) and water line(s) hookup. If your plumbing comes out of the back wall, insert the floor plumbing cutout lid (G), as shown in Illustration 5. This will close the hole and increase your storage space. If your plumbing comes out of the floor, this hole provides accessibility for drain and water line hookup.

Diagram shows the plumbing access lid (G) being inserted into the back of the vanity.

Step 6: Install Shelf

From the front of the assembly, insert shelf pins at the desired height, ensuring they are level. Place the shelf (H) on top of the shelf pins.

Diagram shows shelf pins being inserted and the shelf being placed on them.

Step 7: Adjust Doors

If you need to adjust the doors, do so in the following manner:

• To adjust door up or down, loosen screws (a) on both hinges, adjust door, and retighten screws.
• To adjust door left or right, turn screws (b) on both hinges, in and out.
• To adjust door in or out, loosen screws (c) on both hinges, adjust door, and retighten screws.

Diagrams show close-ups of hinge adjustments for doors.

Step 8: Remove Drawer

As shown in the diagram, fully extend the drawer and locate the plastic levers on the metal glide tracks. Push the left-side and right-side levers at the same time to disengage the drawer from the drawer glides. Gently lift the drawer up to remove it from vanity (A).

Diagram shows how to disengage and remove the drawer.

Step 9: Reinstall Drawer

To reinstall drawers into vanity (A), fully extend the metal glide tracks. Gently lower and slide the drawer box into the rear glide catch. Next, lower the drawer box to completely rest on the extended glides. Then, push the plastic levers to lock the drawer box in place.

Note: Drawer box alignment can be adjusted if necessary. Spin the adjustment wheel to the left to raise the drawer box, or to the right to lower it. The left and right-side glide heights can also be adjusted independently to find the best alignment position.

CAUTION: DO NOT force the drawer or damage the glides. If the drawer does not slide with ease, remove and try again from the start.

Assembly is now complete. Install desired faucet and drain assemblies (not included) per the manufacturer's instructions to complete the installation.

Diagrams show how to reinstall and adjust the drawer.

• Dust the vanity regularly with a soft, non-lint producing cloth or household dusting product.
• You can clean the vanity with a gentle, non-abrasive household cleaner.
• Make sure to dry the wood immediately with a soft cloth or towel.
• The stone top can be cleaned using standard marble cleaning agents available at your local supplier.
• Tips for using touch-up pen (AA): For scratches, stroke in the direction of the scratch. Rub off excess colorant promptly with a soft cloth.

IMPORTANT

• Shade variations and patterns are an inherent characteristic of stone (e.g., granite, marble, engineered stone). Stone tops will vary from product to product.
• Use caution placing items such as soap or any fragranced material on the stone surface. Use a soap dish, coaster, or similar item to protect the surface.
• If soap or fragranced products come in contact with the stone top, rinse the area with water and dry using a soft non-abrasive cloth.
• WARNING: Use only cleaning agents safe for stone. Check cleaning agent restrictions before use. Damage to the stone may result. The manufacturer is not responsible for damage caused by improper cleaning agents or soaps. Warranty will not cover damage caused by the use of improper soaps or cleaning agents.
• DO NOT use products containing acetone, lemon, vinegar, or other acids on the stone top, as these may cause damage.
• Periodically reseal the stone top using an appropriate stone sealer available from your local home store. Follow the manufacturer's directions for application.

The manufacturer warrants this item against defects in materials and workmanship for a period of one (1) year from the date of original retail purchase. This warranty applies only to the original purchaser.

This warranty does not apply to any damage on the product caused by accident, misuse, modified or improper installation, or by affixing accessories not produced by the manufacturer. The manufacturer is not accountable for product installation during the warranty period.

There is no further expressed warranty. The manufacturer shall not be legally responsible for incidental, consequential, or special damages arising in connection with product use or performance, except as may otherwise be accorded by law. The manufacturer disclaims any and all implied warranties.

For replacement parts, call the customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday. You can also contact them at partsplus@lowes.com or visit www.lowespartsplus.com.

Diagram shows the vanity with parts labeled and a corresponding parts list.

Printed in Vietnam