Allen + Roth 60-Inch Vanity with Top

Product Overview

The 60-inch vanity with top is available in various finishes and top materials. Key item numbers include 1028308, 1028307, 1028306, 1028297, 1028296, and 1028295.

Model numbers include:

• 1116VA-60-242-905: SL WRSVL LT GRY 60-IN VTY TZO TOP
• 1116VA-60-242-901: SL WRSVL LT GRY 60-IN VTY WHT TOP
• 1116VA-60-242-900: SL WRSVL LT GRY 60-IN VTY MBL TOP
• 1116VA-60-201-905: SL WRITSVLE WH 60-IN VTY TZO TOP
• 1116VA-60-201-901: SL WRITSVLE WH 60-IN VTY WHT TOP
• 1116VA-60-201-900: SL WRITSVLE WH 60-IN VTY MBL TOP

Attach your receipt here:

Serial Number: _________________________ Purchase Date: _________________________

For questions, problems, or missing parts, contact the customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

Table of Contents

• Package Contents
• Hardware Contents
• Safety Information
• Preparation
• Assembly or Installation Instructions
• Care and Maintenance
• Warranty
• Replacement Parts List

Package Contents

A diagram shows the vanity with parts labeled A through L.

Hardware Contents (Not Shown Actual Size)

Diagrams illustrate each hardware piece.

Safety Information

CAUTION: Use care when assembling the vanity, take your time and follow the assembly instructions closely.

WARNING: Some steps are more easily handled with 2 adults.

Please read and understand this entire manual before attempting to assemble, operate or install the product.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Preparation

Before beginning assembly, ensure all parts are present by comparing them with the package contents and hardware lists. Do not attempt to assemble if any part is missing or damaged.

Estimated Installation Time: 45 minutes (24 hours for silicone caulk to dry).

Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, silicone caulk, power drill with drill bit, measuring tape, level.

Installation Instructions

1. With 2 people, place the vanity on its back on a flat, scratch-free surface. Locate the Center Support Leg (L) and screw it into the base of the vanity. Lift the vanity upright.

   Note: Clean the area where the vanity will be permanently located, ensuring it does not interfere with water supply and drain lines.

   A diagram shows step 1, illustrating the vanity base with the center support leg being attached.

2. With two people, carefully place the vanity against the wall in its final location. Find and mark the locations of wall studs behind the vanity. Drill holes through the vanity mounting area into the wall studs. Using appropriate mounting hardware (not included), secure the vanity to the wall studs. For increased stability, secure to two wall studs if possible.

   WARNING: Vanity MUST be secured to the wall.

   Note: Use the preassembled levelers on the feet of the vanity to level it. Turning levelers counterclockwise raises the vanity; clockwise lowers it.

   A diagram shows step 2, illustrating the vanity being secured to wall studs.

3. Remove the top (B) and backsplash (C) and place them face down on a scratch-free surface, such as the packaging foam.

   Diagrams illustrate removing the top and backsplash from protective foam.

4. Apply silicone caulk to the top edge of the sink (D). With help from another adult, lower the sink onto the back side of the stone top. Ensure the sink's overflow hole faces the front. Align the sink with the stone top cutout, ensuring equal overhang on all sides. Repeat for the remaining sink.

   Note: Ensure the "BACK" stamps on the sink and top are aligned. Use guide lines for sink placement.

   A diagram shows step 4, illustrating sink placement and alignment on the stone top.

5. Screw bolts (AA) into the threaded holes of the stone top (B).

   Diagrams show hardware AA (Bolt) and its quantity (x8).

6. Lower the sink brackets (BB) over the bolts (AA) and onto the sink lip. Adjust the bracket to firmly grasp the sink lip. Place lock washers (DD) over bolts (AA) and secure with nuts (CC). Hand-tighten nuts (CC) with the wrench (EE). DO NOT OVER TIGHTEN!

   Tip: Check sink centering before caulk dries. If not centered, unscrew clamps, readjust, and retighten.

   Diagrams show hardware BB (Sink bracket), CC (Nut), DD (Lock Washer), EE (Wrench) and their quantities.

7. Helpful tip: Install faucet (not included) before securing the vanity top to the vanity base.

   Apply silicone caulk to the top edge of the wood cabinet. With help from another adult, gently lower the stone top with the assembled sink onto the cabinet. Ensure the stone top is flush with the back of the cabinet and has equal overhang on both sides. Remove excess caulk.

   A diagram shows step 7, illustrating the placement of the assembled top onto the vanity base.

8. Apply silicone caulk to the unpolished side and bottom of the backsplash (C). Position the backsplash on the top (B) and against the wall. Clean any excess caulk.

   A diagram shows step 8, illustrating backsplash placement.

9. To adjust doors: Loosen screws (a) to adjust up/down, turn screws (b) to adjust left/right, loosen screws (c) to adjust in/out. Retighten screws after adjustment.

   Diagrams illustrate door adjustment screws (a, b, c).

10. To remove drawers: Extend drawers fully. Push the plastic levers on both sides of the metal glide tracks simultaneously to disengage the drawer box. Lift the drawer box gently to remove it from the glides. Set aside for re-installation.

    Diagrams illustrate drawer removal steps.

11. To re-install drawers: Extend metal glide tracks. Gently lower and slide the drawer box into the rear glide catch, then lower it onto the extended glides. Push plastic levers to lock the drawer box in place. Repeat for remaining drawers.

    Note: To adjust drawer box height, spin the adjustment wheel. Left raises, right lowers. Adjust left and right side glide heights independently.

    CAUTION: DO NOT force drawers or damage glides. If a drawer does not slide easily, remove and try again.

    Assembly is complete. Install faucet and drain assemblies as per their manufacturer's instructions.

    Diagrams illustrate drawer re-installation and adjustment.

Care and Maintenance

• Dust regularly with a soft, non-lint producing cloth.
• Clean the vanity with a gentle, non-abrasive household cleaner.
• Dry wood immediately with a soft cloth or towel.
• Clean the ceramic sink with standard ceramic cleaning agents.
• For scratches or worn areas on the touch-up pen (FF), stroke in the direction of the scratch or wood grain. Rub off excess colorant with a soft cloth.

IMPORTANT

• Shade variations and patterns are inherent to stone tops. Use caution placing items like soap or fragranced materials directly on the stone. Use a soap dish or coaster.
• If soap or fragranced products contact the stone top, rinse with water and dry with a soft cloth.
• WARNING: Use only cleaning agents safe for stone. Check cleaning agent restrictions. Damage may result from improper use. Warranty does not cover damage from improper cleaning agents or soaps.
• DO NOT use products containing acetone, lemon, vinegar, or other acids on the stone top, as they can cause damage.
• Periodically reseal the stone top using an appropriate stone sealer, following manufacturer's directions.

Warranty

The manufacturer warrants this item against defects in materials and workmanship for one (1) year from the date of original retail purchase. This warranty applies only to the original purchaser.

The warranty does not cover damage from accident, misuse, modified or improper installation, or accessories not produced by the manufacturer. The manufacturer is not liable for damages caused by cleaners or soaps that etch or stain the stone top. The manufacturer is not responsible for product installation during the warranty period.

There is no expressed warranty beyond this. The manufacturer is not legally responsible for incidental, consequential, or special damages arising from product use or performance, except as provided by law. The manufacturer disclaims all implied warranties.

Replacement Parts List

For replacement parts, contact customer service at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

A diagram shows the vanity with parts labeled A through L.

Hardware diagrams are shown for AA through KK.

Replacement Parts List for 1116VA-60-242

For replacement parts, contact customer service at 1-866-439-9800, 8 a.m. - 8 p.m., EST, Monday - Sunday.

A diagram shows the vanity with parts labeled A through L.

Hardware diagrams are shown for AA through KK.