Safety Information
Please read and understand this entire manual before attempting to assemble, operate or install the product.
⚠ Warning
- This product is not a toy and contains small parts. Close supervision is necessary when this unit is used near children. The remote control contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours. Seek medical attention immediately.
- For cleaning, use a soft dry cloth.
⚠ Caution
- To avoid damage to tape, do not fold or bend around corners. The minimum bending radius is 1 inch (2.54 cm), whether lighted or unlighted.
- Do not route cords through walls, ceilings or any other like part of a building.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna; Increase the separation between the equipment and the receiver; Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003.
Preparation
Tools Required (Not Included)
- Phillips head screwdriver
- Measuring tape
- Ladder
Package Contents
- A: Remote control (x1) - A rectangular device with multiple buttons.
- B: LED Tape Light (x1) - A long, flexible strip of LEDs.
- C: Receiver (x1) - A small black box with ports for connections.
- D: Power adapter (x1) - A power supply with a plug.
Hardware Contents
Note: Hardware shown actual size.
- AA: Mounting clips (x32) - Small rectangular clips with a screw hole for securing the tape light.
- BB: Screws (x16) - Small screws for use with mounting clips.
Installation Overview
- Unroll the LED tape light (B). (Diagram shows the tape light unrolled.)
- Secure the tape light using mounting clips (AA) and screws (BB). (Diagram shows a hand screwing a clip onto the tape light.)
- Ensure the tape light is not folded or bent sharply. The minimum bending radius is 1 ft. (30.48 cm). (Diagram shows the tape light bending around a corner, with a measurement indicating 1 ft. / 30.48 cm.)
- Plug the lead wire from the tape light into the lead wire from the receiver (C). (Diagram shows a close-up of two cables connecting, one from the tape light, one from the receiver.)
- Locate the receiver (C) so that its 'eye' (infrared sensor) is visible to the remote control. (Diagram shows the receiver with an arrow pointing to the IR sensor, labeled 'eye'.)
- Connect the power adapter (D) to the receiver (C). (Diagram shows the power adapter plugged into the receiver.)
- Plug the power adapter (D) into a standard electrical outlet. (Diagram shows the power adapter plugged into a wall outlet.)
- Use the remote control (A) for independent on/off control of RGB versus warm white LEDs, 20 RGB color presets, four levels of warm white light output (25%-50%-75%-100%), and fade and flash effects with speed variation. (Diagram shows the remote control with various buttons.)
Care and Maintenance
Ensure power is off before cleaning. Clean with a mild glass cleaner and soft cloth. Apply liquid cleaner to cloth. Do not spray fixture itself.
Warranty
This fixture is warranted to be free from defects in materials and workmanship for 3 years from the date of original purchase. For a Return Authorization number and further instructions, call 1-866-994-4148. The manufacturer is responsible for replacing the defective item and is not liable for any other loss, damage, or injury caused by the product.
Troubleshooting
| Problem | Possible Cause | Corrective Action |
|---|---|---|
| Tape light will not operate. | No power to fixture. | Verify that circuit breaker is not tripped. |
| Switch is in off position. | Use slide switch on dimmer to turn on tape light. |
Customer Support
For more information, visit www.lowes.com.
If the item is no longer for sale, or if there are any questions or problems, call the customer service department at 1-866-994-4148, Monday - Thursday, 8 a.m. - 6 p.m. EST, and Friday, 8 a.m. - 5 p.m. EST.
For additional information, visit Lowes.com, search the item number, and refer to the Guides & Documents tab on the product's page.
