Magicshine SEEMEE 100AD User Manual

Important Safety Information

⚠️ WARNING!

1. To prevent inadvertent switching on, please keep the light unit in lockout mode before transport or storage.

2. DO NOT disassemble, modify, remanufacture, puncture, or damage the device or batteries.

In the Box

• SEEMEE 100AD taillight: A compact, rear-facing bicycle light.
• Saddle mount: A bracket designed to attach the light under a bicycle saddle.
• Seat post mount: A bracket designed to attach the light to a bicycle seat post.
• USB-C charging cable: A cable for charging the taillight's internal battery.

Quick Guide

The SEEMEE 100AD features a Power button and a Detection button. [Diagram Description: A rectangular bicycle taillight with two circular lenses at the top and a larger circular lens at the bottom. Arrows point to the left side labeled "Power button" and the right side labeled "Detection button".]

PelotonSync Flash Mode

When two or more SEEMEE 100AD taillights come close and flash in the same pattern, they automatically switch to PelotonSync Flash mode. Click the power button to exit PelotonSync Flash mode and switch to other modes. (Note: Taillights in detection alert flash mode cannot simultaneously enter PelotonSync Flash mode.)

Detection Alert Function

Detection Alert Function ON/OFF:

1. When the taillight is on, the detection alert function is activated by default.
2. The detection alert function can be turned on or off separately. Click the detection button to turn it on, and the blue indicator is constantly on. Click the button again to turn it off, and the blue indicator will not light up.

Note:

1. When the detection alert function is activated, the taillight automatically detects approaching vehicles within 25 meters from behind and alerts with a rapid 100-lumen flash. The taillight will return to the previous lighting mode when no vehicle is detected within range.
2. If both detection alert flash mode and PelotonSync Flash mode are activated, the taillight enters detection alert flash mode when detecting a vehicle. As the vehicle comes within 5 meters, the taillight switches to PelotonSync Flash mode.

Power Button Instructions

ON/OFF:

Press and hold the power button for 1 second to turn the taillight on/off.

Change Mode:

When the taillight is on, click the power button to cycle through Low ➡️ High ➡️ Night Flash ➡️ Day Flash ➡️ Eco Flash ➡️ Low...

Lockout:

When the taillight is off, press and hold the power button for 3 seconds to enter lockout mode.

Unlock:

In lockout mode, press and hold the power button for 3 seconds or charge the taillight.

Memory Function:

When the taillight is turned on again, it will automatically turn to the last selected lighting mode.

FTR LightSync Control Function

After the remote control is successfully paired with the front and tail lights, press and hold the "○" or "□" button on the remote for 1 second to turn on/off the front and tail lights simultaneously.

Note:

1. The front and tail lights to be paired should support the FTR LightSync Control function, and the remote control cannot be paired separately with a tail light.
2. The remote control and front lights are sold separately.
3. To pair the remote control with the front and tail lights, please refer to the instructions for the MJ-6558 remote control.

Low Power Mode:

When the remaining battery power is below 10%, the taillight will change to Eco Flash mode. During this period, the detection alert function is deactivated.

Output / Runtime

*All data are measured in accordance with ANSI/NEMA FL 1-2009. The test was conducted at a temperature of 25°C and a wind speed of 25 km/h. The runtime may vary depending on external temperature and ventilation conditions, and these deviations may affect the result of testing.

*The stated runtime of each mode excludes the detection alert function. When the detection alert function is activated, the runtime will vary depending on the flashing frequency of the detection alert.

Charging / Battery Indicator

Standard charging time approx. 1.5 hours (5V 1A)

• Charging: Flashing red ?
• Fully charged: Constant green ?

Battery Indicator (when taillight is off):

Click the power button to display the remaining battery level for 3 seconds.

• 100%-21%: Constant green ?
• 20%-11%: Constant red ?
• 10%-1%: Flashing red ?

How to Install

1. Install on Seat Post

[Diagram Description: Steps for mounting the taillight on a seat post. 1. Attach the seat post mount strap around the seat post, tightening it. [Diagram shows strap around post with arrow indicating tightening]. 2. Slide the SEEMEE 100AD taillight onto the mount until it clicks. [Diagram shows light sliding onto mount]. 3. The light is now securely attached. [Diagram shows light attached to seat post]. 4. Final view of the light mounted on the seat post. [Diagram shows final installation].]

2. Install Under Saddle

[Diagram Description: Steps for mounting the taillight under a bicycle saddle. 1. Attach the saddle mount bracket to the saddle rails. [Diagram shows bracket attaching to saddle rails]. 2. Slide the SEEMEE 100AD taillight onto the mount until it clicks. [Diagram shows light sliding onto mount]. 3. The light is now securely attached. [Diagram shows light attached under saddle]. 4. Final view of the light mounted under the saddle. [Diagram shows final installation].]