Magicshine SEEMEE 150 TWINPACK USER MANUAL

Operation Instructions

When the brake sensor is on, the taillight will enter the sleep mode after 5 minutes of inaction and auto-activate on any vibrations. [sensor graphic]

When the brake sensor detects braking, the taillight will light up with maximum output. [braking action graphic]

The brake sensor is not included in the front light.

TURN THE BRAKE FUNCTION ON: When the light is off, press and hold the switch for 3 seconds until the light lights up constantly at the highest output.

TURN THE BRAKE FUNCTION OFF: When the light is off, press and hold the switch for 3 seconds until the light keeps flashing quickly at the highest output.

ON/OFF: Press and hold the switch to turn the light on/off. The default output is the last mode when turned off.

CHANGE MODE: When the light is on, single click the switch to cycle through Low-High-Flash-Group Ride-Smart-Low. The front light is without smart mode.

MEMORY FUNCTION: Mode memory features will save the last selected brightness level automatically.

LOW POWER MODE: When the remaining battery power is low, the switch starts flashing and the lighting mode changes to ECO mode. The brake function is disabled during this period.

Accessory/Structure

SEEMEE 150 FL: Image of the SEEMEE 150 FL bike light.

SEEMEE 150 TL: Image of the SEEMEE 150 TL bike light.

Accessories:

• Handlebar mount (0°): Image of a handlebar mount with 0-degree angle.
• Seat post mount (15°): Image of a seat post mount with a 15-degree angle.
• Saddle mount: Image of a saddle mount for bike lights.
• Micro USB Cable: Image of a Micro USB charging cable.

How to Install

SEEMEE 150 FL:

1. Step 1: Attach the handlebar mount (0°) to the bicycle handlebar.
2. Step 2: Slide the SEEMEE 150 FL light onto the mount.
3. Step 3: Secure the light by tightening the screw.

SEEMEE 150 TL:

Scheme 1: Seat Post Mounting

1. Step 1: Attach the seat post mount (15°) to the seat post.
2. Step 2: Slide the SEEMEE 150 TL light onto the mount.
3. Step 3: Secure the light by tightening the screw.
4. Step 4: Adjust the angle as needed.

Scheme 2: Saddle Rail Mounting

1. Step 1: Attach the saddle mount to the saddle rails.
2. Step 2: Slide the SEEMEE 150 TL light onto the mount.
3. Step 3: Secure the light by tightening the screw.
4. Step 4: Adjust the angle as needed.

Output/Runtime

Charging/Power Indicator

When the light is off, click the switch to activate the battery indicator for 3 seconds.

Charging:

• Charging: [red-flashing-light] indicator.
• Fully charge: [green-solid-light] indicator for 3 minutes.

Power Indicator:

• 0%-10%: [red-flashing-light] indicator.
• 11%-20%: [red-solid-light] indicator.
• 21%-100%: [green-solid-light] indicator.

Image showing a USB port and a charging indicator light. Standard charging time is approximately 2.5 hours using a 5V 1A charger.

Warning

Image of the bike light with a brake sensor component highlighted.

Image of the bike light with a general warning symbol.

All performance measurements are in accordance with ANSI/NEMA FL1-2009 Standard. The tests are performed indoors under a room temperature of 25 degrees Celsius with 25KM/H wind conditions. The runtime may vary depending on the external temperature and ventilation conditions, and these biases may affect the results of testing.

The stated runtime of each mode excludes the brake function. When the brake function is on, the runtime will vary depending on the frequency of braking.

Contact Information

Tel: (+86) 755-295 536 69

Fax: (+86)755-275 897 77

E-mail: support@magicshine.com (order from Magicshine.com online store)

E-mail: service@magicshine.com (order from other sales channels)