Wavlink AERIAL HD6 WiFi 6 Outdoor Mesh Router/AP/Repeater

Hardware Overview

The device features the following ports and indicators:

• 1. 5G Antenna ?
• 2. 2.4G Antenna ?
• 3. Grounding Terminal ⏚
• 4. Status LED ?
• 5. WAN/LAN Port (PoE) [port]
• 6. Pair/Reset Button [button]

LED Indicator Table

Installation

Assembly

Follow these steps for physical installation:

1. Stick two silicone pads on the bracket and post respectively.
2. Thread the cable ties through the fixing point of the bracket.
3. Fix the product to the post with cable ties.

Detailed cable connection steps:

1. Pass the RJ45 cable through the waterproof connector cover.
2. Screw the waterproof seal into the waterproof connector bracket.
3. Pass the RJ45 cable through the waterproof connector bracket, and screw the waterproof connector bracket into the cover.
4. Put the waterproof sealing ring on the waterproof connector bracket.
5. Connect the RJ45 cable to the WAN/LAN port.
6. Screw the connecting cable into the 2.4G and 5G antenna connectors and screw up the connector.

Note: Turn the wrench counterclockwise during assembly to tighten the bracket; turn clockwise to loosen during disassembly.

For lightning protection, use a ground connection if installed in a lightning-prone area.

Connection

2.2.1 Passive PoE (For Router/ AP Mode)

• Connect the "PoE" port of the PoE converter with an Ethernet cable [ethernet] to the device's WAN/LAN port.
• Connect another Ethernet cable [ethernet] from the PoE converter's "LAN DATA IN" port to a "LAN" port on your router. (Skip if connecting wirelessly).
• Plug the power plug ? into the "DC IN(37-57V)" port of the PoE converter and connect the power adapter to an outlet.

2.2.2 Active PoE (For AP/Router Mode)

Connect to a PoE switch.

Attention

1. Use certified CAT5e/CAT6 Ethernet cable with RJ45 connectors.
2. Ethernet cable length should be less than 100 meters (328 feet).
3. If fixed on a post, the post length must be less than the cable ties' length.

Configuration

1. Connecting to PC

1.1 Via Wireless

1. Disconnect any Ethernet cable from your computer ?.
2. Turn on your computer's Wi-Fi ?. Find the product's SSID (e.g., WAVLINK-AX_XXXX, WAVLINK-AX_5G_XXXX) and connect.

1.2 Via Cable

1. Connect an Ethernet cable [ethernet] from your PC/Laptop ? to the LAN DATA IN port of the PoE converter.
2. If using AP/Router function, connect the LAN DATA IN port to the upper router's LAN port after completing steps 4.1 and 4.4.

Login Process

1. When connecting for the first time, a login page should pop up. Alternatively, enter 192.168.10.1 or waplogin.link in your browser's address bar.
2. The default password is admin.
3. Select your Country/Region and Time Zone. For security, set a new login password. Click "Next".

Note: The three colored bars indicate password strength.

Mode Selection

This product supports 4 modes:

4.1 AP Mode

1. The system defaults to AP mode via SSID. Click "Next".
2. Connect the product's WAN/LAN port to the higher-level network. You can change the SSID and encryption mode (WPA2-PSK recommended). Create a strong password. Click "Save".

4.2 EasyMesh Agent Mode

1. Log in to 192.168.10.1 or waplogin.link.
2. Click "Switch Mode", then select "EasyMesh Agent Mode".
3. Click "Save".
4. Enter the Pair Key for this device in the main router's mesh network, or press the Pair button [button] on both the main router and sub-router for 1 second.

Note: If unsure, contact the manufacturer.

4.3 Repeater Mode

1. Click "Switch Mode", then select "Repeater Mode".
2. Scan for Wi-Fi networks ?. Select the desired network and click "Next". If not listed, click "Rescan".
3. Enter the wireless network password. Set the wireless network encryption mode and password for this device. Click "Save".

4.4 Mesh Router Mode

1. Click "Switch Mode", then choose "Mesh Router Mode".
2. Ensure your upper router is connected to this product's WAN/LAN port. The system will guide you to select the WAN Type. Encryption Mode WPA2-PSK is recommended. Create a strong password.

Manual Input

1. Manually add the wireless network you want to relay, enter the device information, and click "Next".
2. Set the wireless network encryption mode and password for this device. Click "Save".

Which WAN Type am I supposed to choose?

• PPPoE: For DSL lines with an account name and password.
• DHCP (Dynamic IP): For cable TV or fiber cable.
• Static IP: If provided with IP address, Subnet Mask, and Default Gateway.

Wi-Fi Password Management

To change your Wi-Fi password, click on "Wireless" ?.

Firmware Upgrade

Follow these steps to update firmware:

Option I

1. Download the latest firmware file from www.wavlink.com -> SUPPORT -> Firmware.
2. Extract the firmware file.
3. Log in to waplogin.link or 192.168.10.1, navigate to "Advanced" and select "Firmware Update".
4. Click the browse button [upload] to locate the firmware file.
5. Click "Upload" and then "Apply". Wait for the process to complete.

Option II

1. Log in to waplogin.link or 192.168.10.1, navigate to "Advanced" and select "Firmware Update".
2. Click "Check New Version" to find the latest version.
3. Click "Download and Upgrade". Wait for the process to complete.

Note: After updating, reset the device and clear your browser cache.

What is firmware upgrade and why do I need it?

Firmware updates fix bugs, add features, and improve product experience and security. Incorrect upgrades may damage the device and void the warranty. For details, visit www.wavlink.com or contact technical support at support@wavlink.com.

More Mesh Devices

A mesh router typically supports up to 7 devices. To add more devices:

1. Log in to waplogin.link or 192.168.10.1.
2. Navigate to "Advanced" -> "Mesh Network".
3. Add devices by entering their "Pair Key". Ensure sub-routers are in Mesh Agent Mode. Alternatively, press the Pair button [button] on the main router and sub-router for 1 second after setting the sub-router as EasyMesh Agent Mode.

FAQ

Q1. Why doesn't the login page appear after entering http://waplogin.link?

• Verify wireless connection ? to the device's SSID. If wired, check cable stability.
• Ensure your computer ? obtains an IP address automatically.
• Try logging in using the IP address 192.168.10.1. If connected wirelessly, check the router's DHCP client list for the device's IP.
• If the issue persists, reset the device.

Q2. How do I restore the device to its factory default settings?

• While the device is powered on, press and hold the Reset Button [button] until all LEDs momentarily turn on.

Q3. What should I do if the LED does not change to solid after completing?

• You might have entered the incorrect Wi-Fi password for your host Wi-Fi. Log into the device's web interface to check and re-enter the password.
• Alternatively, reset the device and reconfigure it.

GNU General Public License Notice

This product includes third-party software under GNU GPL or LGPL. You can copy, distribute, and modify according to the license terms. Contact Wavlink for additional source code files. Programs are distributed WITHOUT WARRANTY.

More information:

• http://www.gnu.org/licenses/old-licenses/lgpl-2.0.html
• http://www.gnu.org/licenses/gpl.html

WEEE Directive & Product Disposal

This product should not be treated as household waste. Hand it over to the applicable collection point for recycling electrical and electronic equipment, or return it to the supplier.