TLAN12 Range Rover Evoque (L551) 2019>
Parts List
| Item | Qty | Description |
|---|---|---|
| A | 1 | TLAN12 Crossmember |
| B | 2 | Handed Side Arms |
| C | 1 | Extension |
| Item | Qty | Description |
|---|---|---|
| D | 2 | M16 x 50 Bolts & Nyloc Nuts |
| E | 8 | M14 x 90 Bolts & S/P Washers |
| F | 4 | M14 x 40 Bolts & S/P Washers |
| G | 6 | M12 x 40 (10.9) Bolts, 2 Nyloc Nuts & 4 S/P Washers |
| H | 2 | M12 x 40 (10.9) Bolts & Nyloc Nuts |
| J | 1 | M12 x 120 (10.9) Bolt & Nyloc Nut |
| K | 12 | 14 x 27 Flat Washers |
| L | 12 | 12 x 25 Flat Washers |
| M | 1 | 30mm O/D x 60mm Long Spacer Tube |
Bumper Removal
- Remove two fixings from the lower edge, remove inner light cluster trim carefully pulling rearwards to reveal one fixing to remove. Remove three fixings in each wheel arch, peel back wheel arch liner to reveal two fixings to remove, carefully release the rear bumper from the body starting at the bumper tips then pull rearwards, the rear panel clips can be very tight to release so take care, unclip any necessary wiring looms.
- Remove the silver bumper brackets and retain brackets and fixings, these are refitted later with the Towbar assembly, these are mounted either side above the rear impact beam mounts.
- Remove the rear impact beam and discard.
- Remove left hand heat shield/bumper bracket one fixing, lower Exhaust by removing six fixings across three brackets, remove the metal shield from the AdBlue tank six fixings, remove the heat shield from under the left hand chassis five fixings, remove four fixings to lower AdBlue tank and carefully support.
- Remove and discard the towing eye from the N/S chassis and the chassis reinforcement from the O/S chassis if fitted.
Towbar Installation
- Insert Items B into each chassis member and loosely fix in place using Items E and Items K.
- Loosely Fix Item A to the rear panel using Items F and Items K. Using Items G with Items L fix Items B to Item A. (It may be necessary on some models to trim the heat shield to avoid contact with the central design)
- Fully tighten all fixings ensuring the Towbar is rigid, square and secure.
- Cut the rear bumper as shown below and refit along with fixing AdBlue tank back into its original position and refit all heat shields.
- Using Item H with Item L and Item J with Item L fix Item C to Item A ensuring Item M is fitted between the lower mounting point.
- Using Item D fix your desired ball bracket and wiring plate (Not supplied in this kit) to Item C.
- Fully tighten remaining fixings.
Assembly Diagram Description
An exploded view illustrates the towbar assembly components. Item A is the TLAN12 Crossmember. Items B are the Handed Side Arms. Item C is the Extension piece. Fasteners include various bolts (Items D, E, F, G, H, J) and washers (Items K, L), along with a spacer tube (Item M). The diagram shows how these parts connect to the vehicle chassis and each other, with dashed lines indicating assembly paths and labels (A, B, C, D, E, F, G, H, J, K, L, M) identifying each part and fastener. For example, Item B is shown attaching to the chassis member with Items E and K. Item A attaches to the rear panel with Items F and K, and then Items B are fixed to Item A using Items G and L. Item C attaches to Item A using Items H, J, L, and M. Item D is used to attach a ball bracket and wiring plate to Item C.
Bumper Cut Details
This diagram shows the dimensions required for cutting the rear bumper. It indicates a cut section with specific measurements: 45mm from one edge, a central section of 140mm, and another 45mm from the opposite edge. A dimension of 90mm is also indicated, likely relating to the position or depth of the cut. The diagram shows a shaded area representing the part of the bumper to be removed or modified.
Notes
- For Torque settings see general notes overleaf.
- Nose load limits and vehicle manufacturer's trailer / caravan weight limits must be observed.
