Clarke CS600D Digital Safe

⚠️ CAUTION: Do not keep the override keys inside the safe!

Model No: CS600D

Part No: 7710190

INTRODUCTION

Thank you for purchasing this CLARKE Digital Safe. Before attempting to operate the safe, it is essential that you read this manual thoroughly and carefully follow all instructions given. In doing so you can look forward to the safe giving you long and satisfactory service.

GUARANTEE

This CLARKE product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt as proof of purchase.

This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.

Faulty goods should be returned to their place of purchase; no product can be returned without prior permission. This guarantee does not affect your statutory rights.

SPECIFICATION

REPLACEMENT OVERRIDE KEY

A small label is located on the front of each safe with a key number. The number will start with either the letter "J" or "G" followed by several digits. This number must be registered with Clarke International in the event you require a replacement key.

Please complete the registration form at the back of this manual and send it to the address stated with the form. If you fail to register the safe, Clarke International will not be able to provide you with a replacement key.

We recommend that in addition to sending the completed form, you remove the label from the safe and fix it to the space provided in this document for future reference.

Fix or record the key number here: [____________________]

BEFORE USE

OPENING THE SAFE FOR THE FIRST TIME

1. Remove the small plastic cover (B) on the front panel.

2. Insert the override key into the keyhole and turn it counterclockwise. At the same time, turn the doorknob (A) in a clockwise direction to open the safe.

? NOTE: Never keep the override keys inside the safe itself.

3. Replace the small plastic cover (B) onto the front panel.

[Image Description: The front panel of the safe shows a doorknob labeled 'A' and a small plastic cover labeled 'B' covering the override keyhole.]

INSTALLING THE SAFE

The safe should be secured vertically to a wall, shelf, or to the floor using the expansion bolts (supplied).

• There are holes (8 mm) on the rear and bottom of the safe for securing to a wall or the floor. The rear holes are highlighted in the accompanying diagram.

[Image Description: The rear of the safe is shown, with circular mounting holes indicated. Arrows point to these holes, suggesting their use for securing the safe.]

INSTALLING THE BATTERIES

The safe requires 4 x size "AA" (1.5V) batteries.

1. Open the safe.
2. Remove the battery cover plate on the back of the door and install the batteries.
3. Ensure the batteries are fitted with the correct polarity.
4. Use of alkaline batteries is recommended.

[Image Description: A hand is shown inserting batteries into the battery compartment located on the back of the safe door. The polarity markings (+/-) are visible.]

PROGRAMMING THE CODE

1. With the safe door open and the batteries installed, press and release the red button on the rear of the lock housing. You will hear two beeps, and the yellow light will be on at the same time.
2. Enter the code you want to use (3-8 digits) as a combination.
3. Confirm within 15 seconds by pressing the letter "A" or "B".

The safe will “bleep” twice, and the yellow light will go off, indicating your personal code is now set.

5. Test the safe using the new combination immediately.

[Image Description: The rear of the lock housing is shown, with a red button highlighted.]

USING YOUR SAFE

TO OPEN THE SAFE

1. Enter your personal code followed by the letter "A" or "B". You will hear a beep, and the green light on the front of the safe will light up.
2. Turn the doorknob in a clockwise direction to open the door within 5 seconds.

Important Security Notes:

• If an incorrect combination is used 3 times consecutively, the safe will not open, and you must wait for 20 seconds before trying again.
• If the incorrect combination is selected a further 3 times, you must wait approximately 5 minutes before trying again.

BATTERY REPLACEMENT WARNING

If the batteries are low, the red light (in the middle of the number panel) will illuminate.

MANUAL OVERRIDE

For manual override instructions, please refer to the "Opening the Safe for the First Time" section on page 3.

DECLARATION OF CONFORMITY

Clarke International declares that this product complies with relevant EU directives (Electromagnetic Compatibility Directive, Restriction of Hazardous Substances) and UK legislation (Electromagnetic Compatibility Regulations, Restriction of Hazardous Substances Regulations). The product meets the standards EN 61000-6-3:2007+A1:2011 and EN 61000-6-1:2009.

Product Description: Digital Safe

Model Numbers: CS300D, CS400D, CS600D (and others listed in original document)

Date of Issue: 09/03/2021

The CE mark was first applied in 2009. The UKCA mark indicates compliance with UK regulations.

Clarke Quality Products

Clarke International offers a vast range of quality products, including Air Compressors, Generators, Power Washers, Welders, Metalworking and Woodworking machinery, Hydraulics, Water Pumps, Power Tools, and Starters/Chargers.

IMPORTANT INFORMATION REGARDING REPLACEMENT KEYS

In order to obtain a replacement key, it is essential to register your safe. Please detach and complete the Safe Registration Form (provided on the reverse of this section, page 8) and return it to:

Clarke International
Product Registration Department
Shrubland Road
London
E10 7RB

SAFE REGISTRATION FORM

PLEASE COMPLETE AND RETURN TO CLARKE INTERNATIONAL WITHIN 7 DAYS OF PURCHASE.

IMPORTANT! If you fail to register and subsequently lose your key, Clarke International will be unable to provide you with a replacement. It is therefore in your own interest to register immediately.

Model Number Selection

Please tick the relevant box for your model:

• CS300D [ ]
• CS400D [ ]
• CS150F [ ]
• CS300K [ ]
• CS400FP [ ]
• CS600D [ ]

Registration Details

• Name: [____________________]
• Company: [____________________]
• Address: [____________________]
• Post Town: [____________________]
• County: [____________________]
• Post Code: [____________________]
• Tel. No.: [____________________]
• E-Mail: [____________________]

Purchase Details

• Date Purchased: [____________________]
• Purchased From: [____________________]
• Town of purchase: [____________________]
• Receipt Number: [____________________]

Security Details

• Serial Number: [____________________]
• Key Number: [____________________]
• Registration Number: [____________________] (For office use)