Namron Zigbee Dimmer 2-POL 400W

Function Introduction

The Namron Zigbee Dimmer 2-POL 400W is a Zigbee AC phase-cut dimmer based on the latest Zigbee 3.0 protocol. It supports a wide input and output voltage range of 100-240VAC and is compatible with resistive and capacitive loads, offering up to 400W of single-channel output. The device features screw terminals for safe and reliable connections and is available in leading-edge or trailing-edge versions (default is trailing-edge). It enables control of ON/OFF and light intensity for triac dimmable LED lights or LED drivers. As a Zigbee end device, it supports Touchlink commissioning, can pair directly with compatible Zigbee remotes without a coordinator, and can form its own Zigbee network. It also supports find-and-bind mode and can bind up to 20 Zigbee Green Power switches. The dimmer is compatible with universal Zigbee gateway products and can be controlled by push switches or momentary switches. Its mini size allows for easy installation into standard wall boxes. The device operates on a 2.4GHz radio frequency and has a waterproof grade of IP20.

Device Overview:

• Switch Input: Features a 'Reset' key for network pairing, Touchlink, factory reset, and turning the load on/off.
• 'Min. Set' Key: Used to set or delete a minimum dimming level and to set or delete a startup brightness level.
• Terminals: Clearly marked for Live Input (Lin), Neutral Input (Nin), Live Output (Lout), and Neutral Output (Nout). Also includes COM and S terminals for switch connections.

Product Data

Compatible Load Types

Safety & Warnings

• DO NOT install with power applied to the device.
• DO NOT expose the device to moisture.

Zigbee Clusters Supported

• Input Clusters: Basic (0x0000), Identify (0x0003), Groups (0x0004), Scenes (0x0005), On/off (0x0006), Level Control (0x0008), Diagnostics (0x0b05).
• Output Clusters: OTA (0x0019).

Operation and Network Setup

1. Wiring: Ensure all wiring is performed according to the connection diagrams. The Namron Zigbee Dimmer is a wireless receiver that communicates with Zigbee compatible systems via radio signals.
2. Zigbee Network Pairing through Coordinator or Hub:
   1. Remove the device from any previous Zigbee network if it has already been added.
   2. Using your Zigbee Controller or hub interface, select the option to add a lighting device and enter pairing mode as instructed by the controller.
   3. Reset the device's power to initiate network pairing mode. The connected light will flash twice slowly. This mode has a 15-second timeout; repeat the power reset if necessary.
   4. Upon successful pairing, the connected light will blink 5 times and then remain solid. The device will then appear in your controller's menu for operation.
3. TouchLink to a Zigbee Remote:
   1. Method 1: Short press the 'Reset' button 4 times (or reset power 4 times) to start Touchlink commissioning immediately (180s timeout).
   2. Method 2: Reset the device's power. If not added to a Zigbee network, Touchlink commissioning starts after 15 seconds (165s timeout). If already added, it starts immediately (180s timeout). Repeat if timeout occurs.
   3. Bring the Zigbee remote or touch panel within 10cm of the lighting device.
   4. Initiate the Touchlink commissioning on the remote or touch panel as per its manual.
   5. Successful linking is indicated by an indication on the remote and the connected light flashing twice.
   6. Note: Directly TouchLinking (both devices not in a network) allows 1 remote per device. After adding both to a Zigbee network, each device can link with up to 30 remotes. For control via gateway and remote, add both to the network first, then TouchLink. Linked remotes can control the device after TouchLinking.
4. Removed from a Zigbee Network through Coordinator or Hub Interface: From your Zigbee controller or hub interface, select the option to delete or reset the lighting device. The connected light will blink 3 times to confirm successful removal.
5. Factory Reset through a Zigbee Remote (Touch Reset): Ensure the device and remote are on the same network or the remote is not added to any network. Bring the remote/touch panel within 10cm of the device. Initiate the Touch Reset procedure on the remote/touch panel as per its manual. Reset the device's power to start the process (180s timeout). Successful reset is indicated by the remote's indication and the connected light flashing 3 times.
6. Find and Bind Mode: Ensure the device and remote are added to the same Zigbee network. Set the remote or touch panel (target node) into find-and-bind mode as per its manual. Short press the 'Reset' button 3 times on the dimmer (or reset its power 3 times) to start Find and Bind mode (connected light flashes slowly) to find and bind the target node (180s timeout). Successful binding is indicated on the remote/touch panel, allowing control of the device.
7. Factory Reset Manually: If the device is already at factory default, no indication will appear upon resetting. All configuration parameters will be reset. To reset, short press the 'Reset' key 5 times continuously. If the 'Reset' key is not accessible, reset the device's power 5 times continuously. The connected light will blink 3 times to indicate a successful reset.
8. Learning to a Zigbee Green Power Switch: Short press the 'Reset' button 4 times on the dimmer (or reset its power 4 times) to start the learning mode (connected light flashes twice, 180s timeout). Set the green power switch into learning mode as per its manual. A successful learning is indicated by the connected light flashing twice, enabling switch control of the device. Each device can learn up to 20 Zigbee green power switches.
9. Delete Learning to a Zigbee Green Power Switch: Short press the 'Reset' button 3 times on the dimmer (or reset its power 3 times) to start the delete learning mode (connected light flashes slowly, 180s timeout). Set the paired green power switch into learning mode as per its manual. Successful deletion is indicated by the connected light flashing 4 times.
10. Setup a Zigbee Network & Add Other Devices (No Coordinator Required): Short press the 'Reset' button 4 times on the dimmer (or reset its power 4 times) to enable the device to set up a Zigbee network (connected light flashes twice, 180s timeout). Set another device or remote into network pairing mode and pair it. Pair more devices and remotes as needed. Bind the added devices and remotes through Touchlink for control. Note: Each device can link with a maximum of 30 remotes, and each remote can link with a maximum of 30 devices.
11. OTA (Over-The-Air Update): The device supports firmware updates via OTA and will automatically acquire new firmware from the Zigbee controller or hub every 10 minutes.
12. Setting Minimum Brightness: Adjust the brightness to a desired level via the Zigbee hub/controller or remote. Then, press and hold the 'Min. Set' key until the connected light flashes. This sets the minimum dimming level. The connected load can only be dimmed between this minimum level and 100%. The dimmer range is 1%-100%, but some loads may flicker at 1%; setting a higher minimum brightness can prevent this.
13. Delete Minimum Brightness: Adjust the brightness to 100% via the Zigbee hub/controller or remote. Press and hold the 'Min. Set' key until the connected light flashes, confirming the minimum brightness has been deleted.
14. Set Startup Brightness: Adjust the connected load's brightness to a desired level between 1%-50%. Double-click the 'Min. Set' key to set this as the startup brightness. The load will turn on to this startup brightness and then adjust to the brightness level it was at before being turned off. This feature helps prevent issues with dimmable LED drivers that may not turn on at very low brightness levels.
15. Delete Startup Brightness: Adjust the connected load's brightness to 0%. Double-click the 'Min. Set' key to delete the previously set startup brightness.
16. Controlled by a Push Switch: Connect a push switch to the S1 and COM terminals. A single click of the push switch will turn the light ON/OFF. Pressing and holding the switch will increase or decrease the light intensity.

Wiring Diagrams

Notes for the diagrams:

• Lin: Terminal for live lead input
• Nin: Terminal for neutral lead input
• Lout: Terminal for live lead output
• Nout: Terminal for neutral lead output
• S1: Terminal for switch (used for inclusion/exclusion mode)
• COM: Terminal for grounding to the switch connected to the dimmer

1) With Single Push Switch

Diagram Description: Shows the Namron Zigbee Dimmer with terminals Lin, Nin, Lout, Nout, S1, and COM. A single push button switch is connected between the S1 and COM terminals. The live input (Lin) and neutral input (Nin) are connected to the dimmer. The live output (Lout) and neutral output (Nout) are connected to the load.

2) With Multiple Push Switches for Multiple Control Points

Diagram Description: Shows the Namron Zigbee Dimmer with terminals Lin, Nin, Lout, Nout, S1, and COM. Multiple push button switches are connected in parallel between the S1 terminal and the COM terminal. The live input (Lin) and neutral input (Nin) are connected to the dimmer. The live output (Lout) and neutral output (Nout) are connected to the load.

Product Dimension

Diagram Description: Illustrates the physical dimensions of the Namron Zigbee Dimmer: 45mm (width) x 45.5mm (height) x 20.3mm (depth).

Notes on Inrush Current and Load Compatibility

• The maximum allowed inrush current for this dimmer is 75A (cold start). When connecting LED drivers or LED luminaries in parallel, ensure the total inrush current does not exceed this limit.
• It is recommended to connect no more than 10 parallel LED drivers or luminaries to prevent damage from high inrush current during startup.
• This phase dimmer supports leading-edge (forward phase control) or trailing-edge (reverse phase control) dimming. The default factory setting is trailing-edge. A leading-edge version is available upon request. Ensure your connected loads are compatible with the chosen control type. Refer to the load's user manual or consult the supplier for compatibility.

Importer Information

Namron AS
Nedre kalbakkvei 88B
1081 Oslo
Norway

Made in China