Namron Simplify 1-2-pole Relay 16A
Company: Namron AS
Address: Nedre Kalbakkvei 88B, 1081 Oslo, Norge
Supported Protocols: [Bluetooth], [Zigbee], CE, IP20
Quick Start Guide
Risk of personal injury or property damage
Pursuant to Section 21 of the Regulations on Electrical Equipment, installation material intended to be included in a fixed electrical installation can only be installed by a registered installation company. Local safety standards, rules, and regulations should be followed.
Technical Specifications
| Operating voltage | 220-240V 50/60Hz |
| Operating temperature | -20 til +40 °C |
| Relative humidity | 8 - 80% |
| IP Grade | IP20 |
| Measurements | 45.9x43.4x17.5 mm |
| Load | LED: 1500 VA (1 & 2 Pole)
Resistive load: 3500W – 1 Pole, 3000W - 2 Pole |
| Fitting | Mounted in standard wall box |
| Protection | Short circuit protection
Overload protection
Overtemperature protection |
| Protocol and Radio Frequency | Bluetooth 2.4GHz (IEEE 802.15.4)
Zigbee 3.0 2.4 GHz (IEEE 802.15.4) |
Wiring Diagram
The diagrams illustrate two connection configurations for the relay: 1-Pole and 2-Pole. Both diagrams show the connection points for Line (L) and Neutral (N) power supply. They also indicate terminals S1, S2, and P for connecting external momentary switches. A load, such as a light, is shown connected between the Line (L) and the output of the switch.
Connecting Switches
External switches can be connected to inputs S1, S2, and P. Only momentary (spring-return) switches are supported. The inputs support the following commands:
- S1 - On
- S2 - Off
- P - On/Off
NB! Configuration of the device is done in the Namron Simplify app during the pairing process or on a compatible smart home hub.
For a complete instruction manual about the Namron Simplify system and your device, please visit http://www.simplify.namron.com.
Configuration
Download the Namron Simplify app from the App Store or Google Play Store and set up an account or log in to your existing account. This device supports manual OTA (Over-the-Air) software updates via Bluetooth directly from the Simplify app, in both Zigbee and Bluetooth modes. To perform an OTA upgrade, download the Namron Simplify app and follow the instructions in this user manual to activate OTA mode on your device.
Choosing between Bluetooth and Zigbee mode
This device supports both Bluetooth and Zigbee 3.0. By default, the device is configured to use Bluetooth. In Bluetooth mode, if a device is not paired, it will automatically start pairing when powered.
| Function | How | LED indicator |
|---|
| Activate Zigbee mode | Click and hold the Zigbee button for 10 seconds | Flashes green for 5 seconds when mode is changed |
| Activate Bluetooth mode | Click and hold the Bluetooth (BLE) button for 10 seconds | Flashes blue for 5 seconds when mode is changed |
Operation
Device Modes and Pairing
| Function | How | LED indicator |
|---|
| Bluetooth inclusion | Click the Bluetooth (BLE) button 1 time | Pairing - Flashing blue. Successful – Glows blue |
| Bluetooth exclusion | Press the Bluetooth (BLE) button once, then press and hold it again for 10 seconds | Successful - Glowing red |
| Zigbee inclusion | Click the Zigbee button 1 time | Pairing - Flashing green. Successful - Glows green |
| Zigbee exclusion | Press the Zigbee button once, then press and hold it again for 10 seconds | Successful - Glowing red |
| External Switch inclusion and exclusion | Turn the light on. Push an external switch 9 times and the 10th time hold for 5 sec. | Pairing - Lights off-on x2. Successfull - Lights off-on x1 |
| TouchLink inclusion (Both devices need to be paired to same Zigbee network or not paired to any network) | Click the Zigbee button 2 times. Enable TouchLink pairing on the remote device | Pairing - Flashing blue. Successful – Glows blue |
| Find & Bind inclusion (Both devices need to be paired to same Zigbee network) | Click the Zigbee button 3 times. Enable pairing on the remote device | Pairing - Flashing purple. Successful - No indication |
Advanced Operations
| Function | How | LED indicator |
|---|
| Setting your device back to factory mode | Click the Zigbee or Bluetooth (BLE) button 2 times. 3rd time, hold for 10 seconds | Successful – Glows red |
| Enable OTA mode for manual update with the Simplify app | Zigbee mode - Click 10 times on Zigbee button. BLE mode - Click 10 times on BLE button | Successful – Flashes between red and blue |
| Disable buttons (To prevent the cables in the wallbox from accidentally triggering the configuration by pressing the button.) | Click the Zigbee or Bluetooth (BLE) button 6 times. 7th time hold for 3s | Enable - LED 1 & 2 Flashes yellow 3 times. Disable - LED 1 & 2 Flashes yellow 3 times. |
