Shark Navigator Pet Pro Upright Vacuum with Zero-M Technology

Important Safety Instructions

General Warnings:

• Use only identical replacement parts.
• Do not use the vacuum for any purpose other than described in this manual.
• Inspect all parts for damage before use.
• Extension cords are not recommended.
• The vacuum contains no serviceable parts.

Use Warnings:

• Do not allow children to use the vacuum.
• Turn off the vacuum before connecting/disconnecting accessories.
• Do not handle the plug or vacuum with wet hands.
• Do not use without filters.
• Only use Shark branded filters and accessories.
• Do not damage the power cord.
• Do not put objects into nozzle or accessory openings.
• Do not use if nozzle or accessory airflow is restricted.
• Keep openings away from hair, face, fingers, feet, or loose clothing.
• Do not use if the vacuum is not working properly, has been dropped, damaged, left outdoors, or dropped into water.
• Use extra care when cleaning on stairs.
• Do not leave the vacuum unattended while plugged in.
• Keep the vacuum moving over the carpet surface at all times when powered on.
• Do not place the vacuum on unstable surfaces.
• Do not use to pick up liquids, large objects, hard or sharp objects, large quantities of dust, smoking or burning objects, flammable or combustible materials, or toxic materials.
• Do not use in poorly lit areas, wet or damp surfaces, outdoor areas, or enclosed spaces with explosive or toxic fumes.
• Turn off all controls before plugging in or unplugging.
• Unplug when not in use and before any maintenance or cleaning.
• Hand wash with water only.
• Do not cut anything other than hair, fibers, or string wrapped around the brushroll during cleaning or maintenance.
• Allow all filters to air-dry completely before replacing.
• Ensure dust cup and all filters are in place after maintenance.
• Secure the power cord around the cord hooks during storage.

Polarized Plug: This appliance has a polarized plug (one blade is wider than the other). It fits in a polarized outlet only one way. If it does not fit, reverse the plug or contact a qualified electrician.

Assembly

What's Inside:

• A Vacuum
• B Handle & Hose
• C Wand
• D Duster Crevice Tool
• E Upholstery Tool
• F Dusting Brush

Steps:

1. Insert wand into pod. [Click]
2. Insert handle into wand. [Click]
3. Attach hose to the back of the vacuum pod.
4. Attach hose to the clip on the wand.
5. Store accessories on tool storage posts.

Ensure all parts are firmly clicked into place for proper operation.

*Accessories may vary depending on the model.

*The image shown here is for illustrative purposes only and may be subject to change.

Emptying the Dust Cup

Empty the dust cup after each use.

1. Press the top release button on the dust cup handle. Tilt the dust cup forward and lift to remove.
2. Press the lower release button to open the bottom of the dust cup.
3. To remove collected debris from the Lint Screen, press the top release button and lift the handle to open. Gently brush the lint screen to clean.
4. To reinstall, place the bottom of the dust cup into the pod and tilt back until it clicks into place.

Maintenance

Zero-M Technology: Shark's Zero-M™ self-cleaning brushroll delivers non-stop hair removal. Check for blockages or objects caught in the brushroll if you run over a hard or sharp object or notice a noise change. Visible hair wrap on the brushroll will eventually make its way to the dust cup.

Cleaning the Brushroll:

• Use a coin to turn locks counterclockwise, then lift the door to access the brushroll.
• Debris Wrapped Around Brushroll: Clean off any debris on the bristles. If hair is wrapped, extending cleaning time will help Zero-M technology remove it. If fibers remain, carefully cut debris with scissors.
• Debris Behind Brushroll: If you run over a hard or sharp object or notice a noise change, check for blockages behind the brushroll. Clear away any dust, dirt, or blockages in the Debris Intake. To close the cover, push down until it clicks, then close the locks with a coin.

Cleaning Filters:

Regularly clean and replace filters to maintain suction power. Rinse with cold water only and allow to air-dry completely (at least 24 hours) before reinstalling.

Pre-Motor Filters (Foam & Felt): Clean every 3 months. Remove dust cup, then lift out filters.

HEPA Filter: Clean every year. Press down the top of the filter door, tilt and lift it out. Press the tab at the top of the HEPA filter and pull it away from the vacuum base. To reinstall, insert the HEPA filter and replace the filter door.

Replacing Filters:

• Pre-Motor Filter: Replace every 2.5 years.
• HEPA Filter: Replace every 3 years.

Whole-Home Cleaning

Floor Cleaning:

1. Hard Floor (Setting I): Press switch to I for hard floor surfaces and small area rugs.
2. Carpet (Setting II): Press switch to II for low and high pile carpet cleaning.
3. To engage the brushroll, step on the floor nozzle and tilt the handle back.

Suction Control: Adjust suction using the slider on the handle. Use MIN for reduced suction on carpets and MAX for increased suction on bare floors.

Above-Floor Cleaning:

• Above-Floor-Wand: Press the Wand Release button to detach the wand from the pod.
• Above-Floor-Handle: Press the Handle Release button to detach the handle from the wand.
• Attach desired cleaning accessory to the handle or wand.

*Note: Your quick guide shows the accessories included with your model. Images are for illustrative purposes only.

Checking for Blockages

Emptying the Dust Cup: Detach dust cup, empty, remove debris from lint screen, and check for blockages.

Brushroll Area: Use a coin to turn locks counterclockwise, lift the door, and check for debris wrapped around or behind the brushroll. Clear any blockages.

Hose and Pod: Detach hose from vacuum pod and check hose and opening on the back of the pod for blockages. Detach wand from floor nozzle and handle, and check both ends for blockages. Detach wand from power unit, lay unit down, and check opening for blockages. Detach handle from wand and hose from vacuum pod, and check openings for blockages.

Troubleshooting

Vacuum is not picking up debris. No suction or light suction:

• Check filters for cleaning needs. Rinse and air-dry filters before reinserting.
• Empty the dust cup.
• Check hose, connections, nozzle, wand, pod, and accessories for blockages. Clear any blockages.
• If string, carpet fibers, or hair are wrapped around the brushroll, extend cleaning time for Zero-M™ technology to remove it. If fibers remain, remove the floor nozzle cover and carefully cut debris with scissors.

Vacuum lifts area rugs:

• Ensure the Power/Surface switch is set to Hard Floor (setting I).
• Suction is powerful; use caution on area rugs or rugs with delicate edges.

Brushroll does not spin in carpet cleaning mode:

• If the Brushroll Indicator Light turns red, turn off and unplug the vacuum. Remove pod from floor nozzle and clear any blockages. Reconnect, plug in, and turn on.
• With power on, recline the handle to automatically turn on the brushroll.
• Ensure the Power/Surface switch is set to Carpet (setting II) for the brushroll to spin.

Vacuum turns off on its own or indicator light flashes red:

The vacuum has a motor-protective thermostat. If it overheats, the motor turns off. To restart:

1. Turn off and unplug the vacuum.
2. Empty dust cup and clean filters.
3. Check for blockages in hose, accessories, and inlet openings.
4. Allow the unit to cool for at least 45 minutes.
5. Plug in and turn on the vacuum.
6. Restart the unit with the Power/Surface switch.

Technical Specifications

• Voltage: 120V, 60Hz
• Amps: 9.5A

Product Information

Please read carefully and keep for future reference.

SharkNinja Operating LLC

Illustrations may differ from actual product. Specifications are subject to change without notice.

For SharkNinja U.S. Patent information, visit www.sharkninja.com/USPatents

©2018 SharkNinja Operating LLC. SHARK and SHARK NAVIGATOR are registered trademarks of SharkNinja Operating LLC. NAVIGATOR and ZERO-M are trademarks of SharkNinja Operating LLC.

Printed in Mexico