Foscam Quick Setup Guide

1 Getting Started

Package Contents

• IP Camera
• Network Cable
• Waterproof Lid
• Wi-Fi Antenna ?
• Expansion Screws
• Power Adapter ?
• Mounting Template
• Quick Setup Guide

Security Tips

• Change camera password regularly (numbers, letters, special characters).
• Update camera software and firmware for best experience.
• Warning: Cords are a potential strangulation hazard. Keep out of reach of children. ⚠️

2 Physical Description

Camera Components:

• Microphone ?
• Spotlight & Infrared LED
• Lens ?
• Light Sensor
• Speaker ?
• Antenna ?
• LAN Port [Ethernet Port]
• Power Port ?
• Micro SD Card Slot [Micro SD Slot]
• Reset Button [Reset Button]

3 Setting Up Your Camera: Connection via the Foscam App (Recommended)

Before You Get Started

Download and install the Foscam APP by scanning the QR code provided in the physical document. (Note: QR code itself is excluded from output).

Smartphone Specifications:

• iOS: version 11 or higher.
• Android: 5.0 or higher, with a Graphics Processing Unit (GPU).

Note: Update the APP to the latest version for the best experience.

Wi-Fi Connection

1. Tighten the antenna clockwise ? and ensure it is vertical.
2. Plug the power adapter ? into the camera. Wait for the "Ready for WiFi configuration" voice prompt.
3. Ensure your smartphone is connected to your Wi-Fi router (2.4 GHz or 5 GHz).
4. Open the Foscam APP. Register a new account or sign in.
5. Follow the app steps:
   • Tap "Add Device".
   • Select "Scan QR Code".
   • Scan the QR code located on your device.
   • Confirm you heard the "Hello Foscam" voice prompt and tap "Next".
   • For Wi-Fi configuration, keep the device and phone close to the router (6-12 inches / 15-30cm).
   • Point the phone's QR code towards the camera.
   • Enter your Wi-Fi password and tap "Confirm".
   • Confirm you heard the "WiFi connecting" voice prompt and tap "Next".
   • Wait for the device to add successfully (approx. 2 minutes).
   • Set a device name (e.g., "Garden", "Living Room").
   • Save the device's QR code to your mobile album for easier re-adding.
   • Tap "Submit" after setting a new camera username and password.

Note: If adding fails, reset the camera and try again.

4 PC Access Your Camera

Foscam VMS

Foscam VMS is a PC tool for managing multiple Foscam HD cameras (up to 36). It is compatible with Windows and Mac.

Download Foscam VMS:

• Windows: www.foscam.com/vms
• Mac: Mac App Store

Note: Update Foscam VMS to the latest version for the best experience.

Add the IP Camera via VMS

1. Run Foscam VMS, create a local administrator account, and log in.
2. Tap the "+" icon and follow the setup wizard to add your camera.

For detailed steps, visit foscam.com/downloads.

5 Hardware Installation

Point the camera at the desired location and use the provided screws to mount it. The camera offers adjustable angles: 0-90° vertically and 0-360° horizontally.

Please Note: Ensure that rain or water does not reach the connector ports at the end of the tailcable, as these connectors are not weather-resistant.

6 Important Notice

Camera Username & Password

Use strong, unique passwords for camera access and management to enhance security. If forgotten, press the "Reset" button (hold for 3-5 seconds) to reset the camera.

Storage Media

Your camera supports Cloud Storage ☁️, NVR (Network Video Recorder) [NVR], and Micro SD card (FAT32 & exFAT format) storage.

Micro SD Card Formatting

Follow these steps to format your Micro SD card:

1. Scan the QR code to download the "Foscam Format" Tool (link: foscam.com/downloads/app_software.html).
2. Open the "Foscam Format" Tool.
3. Select the SD card (e.g., F:\).
4. Accept the Terms of Use.
5. Click "Format". Confirm data erasure when prompted.
6. Wait for "Format ready" [Format Complete].

7 Safety Tips

• Prohibit use at high temperature [High Temp] ?️
• Prohibit use at low temperature [Low Temp] ❄️
• Keep away from fire ?
• Keep away from children ?
• Not a children's toy [Not a Toy]
• Keep dry ?
• Caution: Electricity ⚡
• Use the supplied screw pack ?️
• Use the correct power supply ?

8 Product Performance

• WLAN frequency range: 2412MHz - 2472MHz and 5725MHz - 5850MHz
• Maximum transmission power: < 18dBm
• Wireless Standard: IEEE802.11b/g/n (2.4GHz), IEEE802.11a/n/ac (5GHz)
• Power Supply: DC 12V 1.0A 12W

9 Troubleshooting

IP Camera is not powering on

1. Check if the outlet is working. Try a different outlet.
2. Check the DC adapter. Try another compatible 12V/1A power adapter.
3. If the issue persists, contact Foscam support.

How to re-configure WiFi after router change

1. Connect the camera to your router via an Ethernet cable.
2. In the Foscam app, go to Camera Settings > WiFi Settings, select the new Wi-Fi name, and enter the password.
3. Disconnect the Ethernet cable and wait for the camera to connect wirelessly.
4. Alternatively, reset the camera (press and hold Reset button for 3-5 seconds).
5. Open the Foscam app, scan the camera's QR code to set up the wireless connection, ensuring your phone is connected to the new Wi-Fi.

FCC Warning

15.19 Labeling requirements

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) it may not cause harmful interference, and (2) it must accept any received interference, including interference that may cause undesired operation.

15.21 Information to user

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

15.105 Information to the user

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits provide reasonable protection against harmful interference in residential installations. The equipment generates radio frequency energy and may cause interference to radio communications if not installed and used per instructions. Interference is not guaranteed to not occur in a particular installation. If interference occurs, try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment to a different circuit than the receiver.
• Consulting a dealer or experienced radio/TV technician.

FCC RF Radiation Exposure Statement

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with RF radiation exposure limits for an uncontrolled environment. Install and operate with a minimum distance of 20cm between the radiator and your body.

Support & Manufacturer Information

For support, contact support@foscam.com.

CE Certificate statement: foscam.com/company/ce-certificate.html

Exporter and Importer Information: foscam.com/company/open-information.html

Manufacturer: Shenzhen Foscam Intelligent Technology Co., Ltd

Address: Room 901-902, Building 1B, Shenzhen International Innovation Valley, Xingke 1st Street, Nanshan District, Shenzhen, Guangdong, China, 518055

Website: www.foscam.com

Disclaimer: This guide may be updated slowly due to product upgrades. Official website information is the current standard.