SIHOO V1-M101 Ergonomic Office Chair Installation Guide

Welcome

Hello Friend,

Thank you for choosing a SIHOO office chair. If you need an installation video, please visit our official website at sihoooffice.com.

The chair comes with a product warranty service. If there is any problem with the chair, please contact our after-sales service department on the SIHOO store immediately. We believe they will provide you with a satisfactory solution. If the chair meets your needs, we welcome you to share your feelings.

Please feel free to contact us via the following email: service@sihoooffice.com

Thank you for being one of our customers. We love our customers, and if you need us, we will always be here.

SIHOO

Please separate the elements before sorting: ♻️

CAUTION! Work on gas springs only by trained specialist personnel.

ACHTUNG! Arbeiten an Gasfedern nur durch eingewiesenes Fachpersonal.

Assembly Instruction

1. Screw the castors into the legs.
2. Put the gaslift into the center of the base.
3. Connect the mechanism and seat cushion with 4 M6*25 screws and small spacers.
4. Use three M8*40 screws and spring lamination and small shims to connect the seat cushion to the backrest.
5. Put the upper part of the assembled chair into the gaslift.
6. Insert the armrest into the seat cushion, use the armrest knobs and big shims to install the armrest on the seat cushion.
7. Insert the backrest into the slot.

Installation Safety Guideline

1. Please read through assembly instruction and parts list before any installation.
2. Please check if there are missing parts or any damages.
3. Please put on the protection gloves to avoid any injury when installing.
4. Please choose a spacious and clean place and cover a paperboard on the floor to avoid any friction damage when proceeding the installation.
5. Please fasten all the screws and shims into the installation positions tightly according to the Assembly Instruction.
6. Please be aware that the gaslift would be difficult to remove once installed. If the chair is needed to be removed, firstly, you can apply a rubber hammer to remove it by tapping the gaslift head a few times; then you may take out the chair base. Secondly, tap on the five legs to loosen the gaslift from the base. Please be careful during the operation. (Disclaimers: customers will be responsible for any damage or injury caused by misconduct of installation, please be careful.)

Precautions for Use

1. The product was designed for one person only, please do not be seated more than one person.
2. You shall refer to the functions instruction when you are using the product.
3. The product can only be seated when all the screws and parts are fastened. All parts should be checked on every three months routinely to make sure no loose.
4. Please use the product on the flat floor. Away from humid environment, any fire hazards and direct sunlight.
5. Children under 5 shall be accompanied by adults when using the product.
6. Please do not stand on the chair or use it as a ladder or footsteps.
7. Please do not sit on the armrests in case of causing any danger.
8. Please use a soft cloth to clean up the dust on the product before usage. Do not use rough cloth to wipe the product.
9. For your own safety, please do not uninstall the gaslift.

Functions

• Armrest height adjustment; Armrest left and right adjustment; Armrest forward and backward adjustment.
• Pull out the hand lever to adjust the seat cushion to slide back and forth.
• Seat height adjustment: Rotate the hand lever.
• Headrest height adjustment.
• Pull up the backrest to adjust the backrest.
• Turn the backrest knob to adjust the front and back of the waist pillow and the height of the waist pillow.
• Tightness adjustment for backrest tilting: Tighten / Loosen
• Back tilting position adjustment: pull front the hand lever to adjust; pull back to lock up.

Parts List

(The size will be according to regular measurements; Screws and shims with one more as a backup)

Note: Please separate the screws by size before assembly for easy installation.