Fortin EVO-ALL Installation Guide

Regular Installation

This guide provides the suggested wiring configuration for the Fortin EVO-ALL module in a Toyota Corolla (2024-2025, H-Key). Ensure you have the latest firmware and installation guide from www.fortin.ca.

Vehicle Functions Supported

The module supports various vehicle functions, including:

• Immobilizer bypass
• Lock
• Unlock
• Arm
• Disarm
• Parking Lights
• Trunk (open)
• Tachometer
• Autolight Off
• Door Status
• Trunk Status
• Hand-Brake Status
• Foot-Brake Status
• OEM Remote Monitoring

Module Compatibility and Options

Module Required: EVO-ALL

Firmware Version: 88.[22] MINIMUM

QR Code: Located on the module label, manufactured after 2019.

Program Bypass Option

• C1: OEM Remote status (Lock/Unlock) monitoring.
• A11: Hood trigger (Output Status).
• D2: Unlock before / Lock after (Disarm OEM alarm).

Parts Required (Not Included)

• 1x 5 Amp Fuse
• 1x 5 Amp Fusible

Mandatory Installation

Hood Pin Status: The hood pin switch must be installed. If the vehicle can be remote started with the hood open, set function A11 to OFF.

Technician Requirement: This module must be installed by a qualified technician. Incorrect connections can cause permanent damage to the vehicle.

Wiring Connection Guide

This section details the specific wiring connections for the EVO-ALL module to the vehicle's electrical system. Refer to the diagrams for precise locations and wire colors.

Key Connection Points:

• Steering Column: Connections for (+), ACCESSORY, (+) STARTER, (+) IGNITION, (+) 12V.
• ECU, Driver's ECU: Connections for CAN HIGH, CAN LOW, DOORLOCKS DATA.
• Driver Kick Panel: Connections for (-) IMO, (-) IMI.

Wiring Diagram Overview:

The wiring diagram illustrates the connections between the EVO-ALL module's harness and the vehicle's wiring. Key connections include:

• Power: (+) 12V Battery, Ground.
• Ignition/Start: (+) Ignition, (+) Accessory, (+) Starter.
• Data Links: CAN HIGH, CAN LOW, Door Locks Data.
• Vehicle Status: Hood, Trunk, Door Status, Hand Brake, Foot Brake.
• Other: Tachometer, TPMS (if equipped).

Note on TPMS: TPMS connection is only required if remote start control from OEM remotes is desired and the vehicle is equipped with a Tire Pressure Monitoring System.

DCRYPTOR Programming Procedure

Follow these steps to program the EVO-ALL module using the DCRYPTOR feature.

Required Tools:

• FLASH LINK UPDATER, FLASH LINK MOBILE, or FLASH LINK MANAGER software.
• Microsoft Windows Computer with Internet connection OR Smartphone (Android/iOS) with Internet connection.

Programming Steps:

1. Press and hold the programming button. Connect the 4-Pin Data-link connector. LEDs will alternate between BLUE, RED, YELLOW & BLUE/RED flashes.
2. Release the programming button when the LED is BLUE.
3. Insert the required remaining connectors.
4. Turn the key to the Ignition ON/RUN position. The BLUE LED will flash rapidly. Wait until the BLUE LED turns ON solid.
5. Start the vehicle. The BLUE LED will turn OFF, and the RED LED will turn ON.
6. Turn the key to the OFF position. Remove the key from the ignition switch.
7. Start the vehicle. The RED LED will turn OFF, and the YELLOW LED will turn ON. Wait until the RED and YELLOW LEDs alternate.
8. Turn the key to the OFF position.
9. Disconnect all connectors except the Data-Link (4-pins) connector.
10. Use the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCRYPTOR menu.
11. After programming is completed, reconnect the 4-Pin Data-Link connector and then all other connectors.

Remote Starter Functionality

To use the remote starter functionality:

1. Ensure all doors are closed.
2. Remote start the vehicle using the remote.
3. Unlock the doors with the remote-starter remote or the OEM remote.
4. Insert and Turn the key to the Ignition ON/RUN position.
5. Press the brake pedal.
6. The vehicle can now be put into gear and driven.

Notices and Warnings

Updated Firmware and Installation Guides: Updated firmware and installation guides are available on the Fortin website. It is recommended to update the module to the latest firmware and download the latest installation guide(s) before installation.

WARNING: The information provided is on an 'as is' basis. The installer is solely responsible for verifying circuits before connecting. Fortin Electronic Systems assumes no liability for the accuracy or currency of the information or for any installation errors. This module must be installed by a qualified technician. This guide is for suggestion only and may change without notice. Visit www.fortinbypass.com for the latest version.

MISE EN GARDE: The information in this guide is a representation (as is) without warranty of accuracy. The installer is solely responsible for verifying all wires and circuits before connecting. Fortin Electronic Systems assumes no responsibility for the accuracy of the provided information. Installation is the installer's responsibility. Fortin Electronic Systems assumes no responsibility for any installation, whether correct or incorrect. Neither the manufacturer nor the distributor are responsible for any damages caused by this module, except for replacement due to manufacturing defects. This module must be installed by a qualified technician. The information provided is a suggestion. This instruction guide may change without notice. Consult www.fortinbypass.com for the latest version.