Fortin EVO-ALL Regular Installation Guide

Vehicle Functions Supported

This diagram shows vehicle functions supported by the module (functional if equipped):

• Immobilizer bypass
• Lock
• Unlock
• Arm
• Disarm
• Horn
• Parking Light
• Tachometer
• Rear Defrost
• Comfort
• Group
• AUX.1
• Door Status
• Trunk Status
• Hand-Brake Status
• Foot-Brake Status
• Hood Status*
• Secure Takeover
• OEM Remote monitoring

Module Compatibility and Firmware

Module Required: EVO-ALL

Firmware Version: Check label on module (e.g., 88.[33])

Compatible After: 2019

To update firmware and options, use the FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately).

Programming Bypass Option

Unit Option: C1 - OEM Remote status monitoring (Lock/Unlock)

Unit Option: D6 - Push-to-Start

Unit Option: A11 - Hood trigger (Output Status)

Note: The vehicle's OEM remote and SmartKey remain operable during remote start.

Parts Required (Not Included)

• 3x 1 Amp Diode

Mandatory Installation: Hood Pin

Hood Status: The hood pin switch must be installed. If the vehicle can be remote started with the hood open, set Function A11 to OFF.

Note: Installation of safety elements is mandatory. The hood pin is an essential security element and must be installed.

Wiring Connections Overview

Refer to the wiring diagrams for specific connections. Key connection points include:

• 1: ECU, behind glove box
• 2: Fuse box, A1 fuse box
• 3: ECU, Driver's side fuse box

Detailed diagrams show connections to:

• (+) START/STOP1, (-) CAN LOW, (-) CAN HIGH, (+)12 V, (-) GROUND, (-) START/STOP2, (-) START/STOP3
• (+) IGNITION 1, (+) STARTER, (+) IGNITION 2
• (-) IMO, (-) IMI

Dcryptor Programming Procedure

Follow these steps to program the module:

1. Press and hold the programming button. Connect the 4-Pin Data-link connector. LEDs will flash BLUE, RED, YELLOW & BLUE/RED.
2. Release the programming button when the LED is BLUE.
3. If the BLUE LED is not solid ON, disconnect the 6-Pin Main connector and repeat step 1.
4. Insert the remaining connectors.
5. Press the Push-to-Start button twice to turn ignition ON. The BLUE LED will flash rapidly.
6. Press the Push-to-Start button once to turn ignition OFF. The BLUE LED continues to flash rapidly.
7. Press the Unlock button on the vehicle's OEM remote. The BLUE LED will turn ON solid.
8. Press the foot-brake pedal.
9. Press the Push-to-Start button until the engine starts. Release the foot-brake pedal. The BLUE LED turns OFF, the RED LED turns ON.
10. Press the Push-to-Start button once to turn off the engine.
11. Press the foot-brake pedal.
12. Press the Push-to-Start button until the engine starts. Release the foot-brake pedal. The RED LED turns OFF, the YELLOW LED turns ON. Wait for RED and YELLOW LEDs to alternate.
13. Press the Push-to-Start button once to turn off the engine.
14. Disconnect all connectors except the 4-Pin Data-link connector.
15. Connect the 4-Pin Data-link connector to a computer with the FLASH LINK UPDATER or FLASH LINK MOBILE tool to visit the DCryptor menu.
16. After programming, reconnect all connectors.

Remote Starter Functionality

1. Ensure all doors are closed.
2. Remote start the vehicle using the OEM remote, remote-starter remote, or proximity remote to unlock doors.
3. Enter the vehicle with the SMART-KEY.
4. DO NOT PRESS THE BRAKE PEDAL. Press and release the Push-to-Start button once.
5. Press the brake pedal. The vehicle can now be put into gear and driven.
6. If the Smart-Key is not detected, the vehicle will shut down.

Verification Procedure

Test the remote starter. Remote start the vehicle.

Important Notices

Notice: Updated firmware and installation guides are available on the Fortin website. It is recommended to update the module to the latest firmware and download the latest installation guide(s).

Warning: The information provided is on an "as is" basis. The installer is solely responsible for verifying circuits before connecting. Use only a computer-safe logic probe or digital multimeter. Fortin Electronic Systems assumes no liability for accuracy or installation. Installation is the installer's responsibility. Fortin is not responsible for damages caused by this module, except for replacement due to manufacturing defects. This module must be installed by a qualified technician. This guide is for informational purposes only and may change without notice. Visit www.fortinbypass.com for the latest version.

Tech Support

Phone: 514-255-HELP (4357) or 1-877-336-7797

Website: www.fortinbypass.com