HKS CARBON BRACE Installation Manual

Introduction

Thank you for purchasing the HKS CARBON BRACE. This manual assumes you have the necessary knowledge and tools for safe vehicle service operations and are familiar with automotive systems and basic repair procedures. Always refer to a factory service manual and follow its safety precautions to avoid injury.

This manual highlights important points for safe installation and precautions to prevent damage or accidents. The product is designed for specific vehicles; performance is not guaranteed for inapplicable vehicles. HKS is not liable for damages from incorrect installation, use, modification, or dismantling. Specifications and instructions are subject to change without notice. Keep this manual accessible during use.

Safety Precautions

These precautions are to prevent accidents, injuries, and ensure proper use.

[WARNING] Indicates risk of serious injury and/or possible death.

[CAUTION] Indicates risk of serious injury and/or possible property damage (e.g., vehicle damage).

Installation Precautions

• Installation must be performed by a professional.
• Do not modify or remodel the product.
• Keep removed stock parts; do not discard them.
• Install this product following this manual.
• Tighten all bolts and nuts to the specified torque (shown in this manual or manufacturer's service manual). Failure to do so may damage bolts, nuts, or internal components.

Confirmation after Installation

• Verify that bolts and nuts are tightened to the specified torque.
• Ensure no other vehicle parts contact this product.
• If abnormal noises, smells, or vibrations occur during driving, consult the professional who performed the installation.

Maintenance

Proper maintenance is essential for safety, reliability, and function. Maintenance is the owner's responsibility. Regularly check bolts/nuts, vehicle height, dirt, etc., and perform re-tightening, adjustment, or cleaning as needed.

Troubleshooting

• If the vehicle or product is damaged, seek professional repairs.
• If you experience abnormal noise, smell, or vibration while driving, stop using the product immediately and consult a professional.

Product Installation

Parts List

Carbon Brace Components

FRONT

Diagram showing the components for the front installation. It includes the Front Carbon Brace, two Front Brackets (one for the right side, one for the left side), and four Flange Nuts. Torque specifications are noted: 29.5 N·m for the flange nuts. Arrows indicate 'Vehicle's front' and 'Left Side'.

Installation Procedure

1. Removing the Front Tower Bar

[CAUTION] Perform installation after the vehicle has cooled down sufficiently.

Illustration of the front suspension area. It shows the location of the upper front suspension assembly nuts that need to be removed. A note indicates the diagram is an example on the right side, and the left side removal follows the same steps.

1. Remove the nuts from the upper front suspension assembly.

2. Installing the Front Carbon Brace

[CAUTION] Refer to the service manual for torque specs when tightening bolts and nuts. Make sure to tighten the bolts and/or nuts to the specified torque to avoid damage.

Illustration showing the installation steps for the front carbon brace.

Diagram 2-1: Shows the installation of the front bracket (right side) using the vehicle's front suspension assembly installation nuts. The specified torque is 69 N·m. A note indicates the diagram is an example on the right side, and the left side installation follows the same steps.

Diagram 2-2: Shows the installation of the front carbon brace using the provided flange nuts. The specified torque is 29.5 N·m. A note instructs to install the carbon brace with the sticker on the carbon pipe oriented on the left side (forward of the vehicle).

1. Install the provided front bracket (for right side) to the vehicle, using the front suspension assembly installation nuts. (Torque Specs: 69 N·m)

2. Install the provided front carbon brace to the vehicle, using the provided flange nuts. (Torque Specs: 29.5 N·m)

Install the carbon brace while the sticker on the carbon pipe is oriented on the left side (forward of the vehicle).

Manufacturer Information

HKS Co., Ltd.

7181 Kitayama, Fujinomiya, Shizuoka 418-0192, JAPAN

Website: https://www.hks-power.co.jp/