ASSEMBLY & INSTRUCTION

Important Information Before Assembly

Warranty Information

• We warrant this product to be free from defects in materials and workmanship for three years from the date of original purchase. Proof of purchase is required for all warranty claims.
• This warranty covers the repair or replacement of defective parts only; assembly labor is not included.
• This warranty does not apply to product that has been improperly assembled, subjected to misuse or abuse, or altered or repaired in any way. Liability for consequential damages is excluded to the extent permitted by law.

Read Before Beginning Assembly

• Clear the area: Assemble in a spacious area near the product's final location, preferably on a carpet or protected surface (like the product's cardboard packaging) to safeguard both your floor and the product.
• Recommended Assembly Team: It is recommended that at least two people assemble this product. Having an extra hand can make the process easier. Estimated assembly time is 1 hour.
• Check for all parts: Most parts are labeled or stamped on the raw edge. Ensure all parts are included before starting.
• Read each step carefully: Follow the assembly steps in the correct order. Skipping steps or changing the sequence can lead to difficulties.

Caution

• CHOKING HAZARD - Small Parts: This product contains small parts. Keep out of reach of children. ?
• DO NOT USE POWER TOOLS: Power tools can strip or damage parts and void the warranty. ?️❌
• IMPORTANT: Do not fully tighten any bolts until the entire unit is assembled. This will allow for proper alignment and adjustment during the assembly process. ⚙️

Parts List

This page lists all the items included in this package. Please take a moment to identify the hardware and individual components before beginning assembly.

Hardware Kit

Assembly Steps

Step 1: Connect Headboard Panel

Place Headboard Panel-A (5) and Headboard Panel-B (7) close together.

Attach Headboard Panel-A (5) and Headboard Panel-B (7) to the headboard posts (4) using eight bolts (G).

Attach reinforcing strip (13) to the Headboard Panel-A (5) and Headboard Panel-B (7) using eight bolts (G).

Diagram illustrates connecting headboard panels to posts with bolts and a reinforcing strip.

Step 2: Footboard Assembly

Position the footboard rail (9) between the two footboard posts (12).

Insert the four bolts (C) through the pre-drilled holes.

Hand-tighten all bolts first to ensure proper alignment.

Once aligned, fully tighten all bolts with appropriate tools.

Diagram shows the footboard rail being attached to the footboard posts with bolts, emphasizing hand-tightening first.

Step 3: Assembly of Side Rails

Connect the two side rails (1) and side and corner posts (3) using connectors-A (11) and eight bolts (A) and four washers (F). The washers should be installed to the bottom holes.

Secure the connector at each end of the side rail assembly to the bed frame using eight bolts (E).

Diagram illustrates connecting side rails to corner posts using connectors and bolts, with washers shown being installed at the bottom.

Step 4: Assemble the Bed Frame

Align the mounting brackets on the side rails with the corresponding holes on both the headboard and footboard.

Once all bolts are in place, use the provided Allen wrench to fully tighten eight bolts (B).

Diagram shows the assembled side rails being attached to the headboard and footboard, with bolts being tightened using an Allen wrench.

Step 5: Install the Center Support Bar

Attach the center Support Rail (6) to both ends of the bed frame using bolts (E).

Position the center support bar (8) onto the center support rail (6).

Secure the center support bar (8) using the connector-A (11) and bolts (A).

Note: Ensure all connections are properly aligned before final tightening. This step is crucial for the bed's stability.

Diagram shows the center support rail being attached, followed by the center support bar being placed and secured with connectors and bolts.

Step 6: Install the Center Support Bar

Locate the two remaining center support bars (8).

Attach these bars to the center support rail (6) using two bolts (D).

Secure all connections. Use four bolts (A) and Mattress Gasket (14) to fasten the center support bars (8).

Note: Before completing assembly, double-check that all screws and components are fully tightened.

Diagram shows the remaining center support bars being attached to the center support rail, secured with bolts and gaskets.

Step 7: Install the Bed Slats

Place all bed slats (10) across the side rails.

Note: Before completing assembly, double-check that all screws and components are fully tightened.

Diagram shows bed slats being laid evenly across the assembled frame.

Important Information

Replacement Part or Hardware Request

Request a replacement by logging into the marketplace account in which the purchase was made and sending a message to the seller. To expedite the request, attach applicable images relevant to the request and/or include the part number and quantity.

Warnings

• Age Restriction: The bed is not designed for children under 4 years old. ?❌
• No Jumping or Horseplay: This product is not designed to withstand jumping or rough play. ?‍♂️❌
• Weight Limit: The maximum combined weight on the bed should not exceed 1000 lbs. This includes the weight of the bed itself, mattresses, bedding, and people. ⚖️
• Do not drag or push the bed frame: Always use two people to lift and reposition the bedframe to avoid damage to the frame or the floor. ?‍?‍?➡️

Cleaning & Care

• Cleaning Method: Use a dry or slightly damp soft cloth for cleaning. Avoid abrasive cleaners, which can damage the finish. ?
• Hardware Maintenance: Over time, hardware can loosen. Regularly check and tighten all connections to maintain the bed's stability and prevent damage. ?

Please keep these instructions for future reference!