INMOTION AR Series E-Scooter User Manual

1. Safety Instructions

The electric scooter is a recreational device that can also act as a transporter in public communities. Like all riding products, it can lead to dangerous situations if not used properly.

• Understand that risks can be reduced by following instructions and warnings, but cannot be eliminated entirely.
• Riding the scooter carries risks of injury or death from loss of control, collisions, and falls. Use on flat pavement or level ground without bumps and obstacles. Be alert and slow down in unfamiliar areas.
• Always wear a helmet. Use an approved bicycle or scooter helmet with the chin strap in place. Long-sleeved shirts, long pants, and athletic shoes are recommended.
• Never ride in high heels, sandals, or barefoot. Tie up long hair or bangs that can affect vision.
• Do not attempt your first ride in areas with children, pedestrians, pets, vehicles, bicycles, or other obstacles.
• Respect the rights and property of others. Pass on the left when possible. When approaching a pedestrian from the front, stay to the right and slow down. Be careful to avoid pedestrians, especially the elderly, children, disabled, and pregnant women.
• When approaching from behind, announce yourself and slow down to walking speed when passing. Obey local traffic laws and regulations.
• In places without laws, comply with the safety guidelines in this manual. INMOTION TECHNOLOGIES CO., LTD. is not responsible for property damage, personal injury/death, accidents, or legal disputes caused by violations of safety instructions.
• Do not allow others to ride unless they have read this manual and followed the riding guide video. Assist new riders until they are comfortable with basic operation. Ensure new riders wear helmets and protective gear.
• Before each ride, check for loose fasteners and damaged components. If the scooter makes abnormal sounds or signals an alarm, stop riding immediately. Diagnose via the INMOTION App and contact after-sales service at service@imscv.com.
• Be alert! Scan both far ahead and in front of your scooter. Your eyes are your best tool for avoiding obstacles and low traction surfaces (wet ground, loose sand, loose gravel, ice).
• Read and follow all "CAUTION" and "WARNING" notices. Do not ride at unsafe speeds. Do not ride on roads with motor vehicles.
• Recommended rider age: 14-60 years old. Recommended rider weight: less than 120kg (264.6lbs).
• People who should not ride:
• Anyone under the influence of alcohol or drugs.
• Anyone with a disease that puts them at risk during strenuous physical activity.
• Persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless supervised and instructed.
• Anyone with balance or motor skill problems that interfere with maintaining balance.
• Anyone who is severely overweight.
• Pregnant women.
• Riders under 14 years old should have adult supervision.
• Comply with local laws and regulations. Do not ride where prohibited by local laws.
• Ensure you can clearly see and be seen by others.
• Do not ride in wet or icy weather, or on wet, muddy, icy, or slippery roads. Do not ride over obstacles like sand, loose gravel, or sticks.
• Do not ride at night when visibility is limited.
• Avoid sudden acceleration or deceleration.
• Do not ride faster than the speed limit.
• Do not attempt to charge if the scooter, charger, or power outlet is wet.
• Only use the INMOTION supplied charger (FY-4202000 supply unit).
• Use only INMOTION approved parts and accessories. Do not modify the scooter, as this could lead to injury, damage, or void the warranty.
• Children should not use the scooter or play with its parts. Cleaning and maintenance should be done with supervision.
• Park on flat pavement. If on a slope, the kickstand must face downhill to prevent capsizing. Ensure the scooter is parked stably.
• Perform regular inspections and cleaning for better ride experience.
• This scooter contains non-replaceable batteries.
• Use any battery charger other than the original.
• DC Detachable supply unit.
• Any load attached to the handlebar affects vehicle stability.
• Braking distances may be extended in wet weather.
• LPA and LWA: Do not exceed 70dB(A).
• Anticipate trajectory and speed while respecting traffic laws and the vulnerability of others.

2. Packing List

User Materials:

• User Manual
• Quick Start Guide

Assembled E-Scooter

Accessories:

• 1x Power cable
• 1x Power adapter
• 1x Handlebars
• 1x M5 Wrench
• 1x M6 Wrench
• 1x Inner tube

Carefully check if all items in the packing box are complete and intact. If any part is missing or damaged, contact your point of purchase or the manufacturer via email.

Retain the box and packaging materials for at least 15 days for potential shipping needs.

3. Product Function Diagram

Controls and Components:

• Handlebar Area: Throttle, Bell, Brake lever, Headlight, Dashboard, Power button, Head unit clip.
• Frame: Stem, Folding mechanism, Footrest, Kickstand.
• Wheels and Fenders: Front fork, Front mudguard, Front wheel, Rear wheel, Rear reflector, Front reflector, Air valve.
• Other: Charging port, Head unit mount, Taillight, Plate, Bracket.

4. Control Panel/Dashboard

The dashboard displays information such as speed, battery level, and riding mode. The power button is used for turning the scooter on/off and controlling the headlight.

Riding Modes:

• D (Drive mode): Max speed 25km/h, suitable for general riders.
• S (Sports mode): C1 Max speed 30km/h; C1 Pro Max speed 35km/h, suitable for skilled riders.
• Pedestrian mode: Max speed 6km/h.

Indicators:

• Speedometer: Shows real-time speed. Displays as two short lines when the vehicle is locked.
• Battery level: Indicated by 5 bars; the last bar flashing indicates low battery.
• Light icon: Indicates the headlight status.
• Speed unit: Displays speed in Km/h or Mph. Change unit by holding the handlebar and short pressing the power button 3 times.
• Bluetooth icon: Indicates Bluetooth connection status.
• Cruise mode: Activated automatically when maintaining the same speed. Press brake or throttle to return to manual mode.
• Error indicator: Appears when an error is detected. Refer to the error code table for solutions.

Power Button Functions:

• Long press (>2s): Power on/off.
• Single click (on state): Turn headlight on/off.
• Double click: Switch riding mode.

5. Assembling Your E-Scooter

1. Open the package and take out the scooter.
2. Unfold the stem and fasten the folding wrench. Ensure the unlocking key springs up properly.
3. Place the brake lever on the handlebar and tighten firmly with the M6 wrench. (Note: Re-tighten folding part nuts after long-term use).
4. Install the handles on the stem, tightening them according to the marked position and direction.

Caution: To avoid personal injury, follow assembly instructions. Children are not allowed to participate in assembly.

6. First Ride

Note: For safety, the new scooter is not activated and will beep occasionally after powering on. Until activated, the speed is limited to 5km/h, and ride modes cannot be switched. Download the INMOTION App to activate your scooter and enjoy all features.

1. Download and install the INMOTION App, then register/login your account.
2. Power on the scooter and pair it with the INMOTION App. The scooter will beep upon successful connection.
3. Follow the App instructions to activate the scooter and learn how to ride safely.

You can now start to use your scooter.

7. Charging

Charging Port Location: On the rear fender.

Charger Indicator Light: Red (charging), Green (charged).

1. Open the rubber cap covering the charging port.
2. Insert the battery charger plug into the port.
3. Remove the charger and close the rubber cap when charging is finished.

WARNING:

• Do not charge if the charge port or power cord is wet.
• Use only the original charger and battery pack.
• Do not charge or use the battery if it is damaged or flooded.
• Close the charge port cover tightly when not in use or after charging.
• Never charge indoors.

8. Learning to Ride

Safety Gear: Wear an approved helmet, elbow pads, and knee pads to minimize injury.

1. Check the power level indicator after powering on. Charge if the battery level is low.
2. Stand on the footrest with one foot, then push off with the other foot to start gliding.
3. Stand on the footrest with both feet. Press the throttle on the right handlebar. Note: The motor will not engage until the scooter reaches 3 km/h.
4. Slow down by releasing the throttle and lightly applying the brake lever. Avoid sudden braking and be aware of road conditions.
5. When the scooter stops or slows down, put down one foot and dismount.

Caution: Hard braking can cause loss of traction and falls. Maintain a moderate speed and watch for potential hazards.

9. Security Tips

Failure to follow these instructions could lead to serious injury.

• Do not ride in the rain.
• Do not ride at high speed over speed bumps, thresholds, etc. Ride at low speed on rough roads.
• Do not press the throttle while walking with the scooter.
• Avoid obstacles and watch for road conditions.
• Watch your head when passing through doorways.
• Do not step on the rear fender.
• Do not carry heavy objects on the handlebar.
• Do not ride with only one foot or one hand.
• Do not ride on motorways, public roads, or highways.
• Do not rotate the handle violently at high speed.
• Do not touch the motor while it may be hot after running.
• Do not take your hands off the handlebar while riding.
• Do not ride through puddles; go around them at low speed.
• The scooter is for one rider only. Do not carry passengers, especially children. Do not ride when pregnant.
• Do not ride up and down stairs or jump over obstacles.
• Do not use a mobile phone or wear earphones while riding.

10. Folding and Carrying

Folding:

1. Power off the scooter. Hold the stem, press the locking button, and pull the lever. Bend the handlebar stem towards the footrest.
2. Hold the stem and pull the folding ring. Attach the hook to the locking clip on the side of the mudguard.

Carrying:

Carry the scooter by holding the handlebar stem. Watch out for bumps!

11. Specifications

[1] Typical Range: Tested while riding under full power, 165.3lbs (75kg) load, 25°C, 10mph(15km/h) on average on pavement.

[2] Max slope: Measured under conditions: 165.3 lbs(75.0kg) load with 80% battery, riding 10 meter at a speed of 9 mph (15km/h) from the bottom slope to the top at a speed greater than 4 mph (6km/h).

12. Maintenance

Cleaning:

Wipe the scooter body with a damp cloth. For stubborn stains, use toothpaste with a toothbrush, then wipe with a damp cloth.

NOTE:

• Ensure the scooter is off, the charging cable is disconnected, and the rubber cap is closed during cleaning to prevent damage to electronic components.
• Do not use alcohol, petrol, kerosene, or other corrosive solvents.
• Do not wash with high-pressure water jets.

Charging precautions:

• Do not charge in wet environments.
• Best ambient temperature for charging: 0°C~40° C.
• Keep away from children, animals, and flammable materials during charging.
• Do not store in temperatures from -20°C to 50°C. Do not put the battery pack in fire.
• Fully recharge the battery after each use to extend its life. Completely draining the battery may cause permanent damage.
• Do not charge or use if the battery smells, overheats, or leaks.
• Do not open the battery pack or insert objects into the charging port.
• Use only the original battery and adapter.
• Comply with local environmental protection laws for battery recycling.

Storage:

Store the scooter in a cool, dry place when not in use. Do not store outdoors for extended periods.

NOTE: Sunlight, overheating, and excessive cold can accelerate tire aging and affect the scooter and battery life.

WARNING:

• Use only original batteries; other brands may pose a safety risk.
• Do not exceed specified temperatures for storage or charging.

13. Before Your Ride

1. Read instructions carefully. Do not ride if you cannot follow them completely.
2. Do not allow others to use the scooter without reading instructions or understanding safety precautions.
3. Ensure all parts are properly installed. Improper installation can lead to loss of control, collision, or falls. Power off the scooter before installation/maintenance and tighten components correctly.
4. Purchase insurance to minimize risk.
5. Before each ride, check all components: wheels, battery level, running condition, handlebar, stem, tires, brakes, screws. Ensure nothing is loose or damaged. If anything unusual is noticed, stop using immediately and contact after-sales service.
6. Be aware of and comply with all local laws, regulations, and policies for scooter riding.

14. Safety Alerts & Error Messages

The dashboard displays fault codes for scooter failures. Contact after-sales service if solutions do not resolve the problem.

15. Trademarks and Legal Notices

INMOTION is a registered trademark of INMOTION TECHNOLOGIES CO., LTD. Android and Google Play are trademarks of Google Inc. App Store is a service mark of Apple Inc. Respective owners reserve their trademarks.

This manual includes descriptions and instructions for the scooter's functions at the time of printing. Due to product improvements and design changes, your scooter may differ slightly. INMOTION TECHNOLOGIES CO., LTD. reserves the right to change design and functionality without prior notice.

All rights reserved by INMOTION TECHNOLOGIES CO., LTD.

16. Certifications

Model: C1PRO/LX207

This product is certified to ANSI/CAN/UL-2272 by UTL.

The battery complies with UN/DOT 38.3.

FCC ID: 2ADUSC1PRO

FCC Compliance Statement: This device complies with Part 15 of the FCC rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with Class B digital device limits per FCC Rules, providing reasonable protection against harmful interference in residential installations. It generates, uses, and radiates radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. No guarantee against interference in a particular installation. If interference occurs, try correcting it by:

• Reorienting or relocating the receiving antenna.
• Increasing separation between equipment and receiver.
• Connecting equipment to a different circuit outlet.
• Consulting a dealer or experienced radio/TV technician.

This equipment complies with FCC radiation exposure limits for uncontrolled environments.

RoHS Directive: INMOTION TECHNOLOGIES CO., LTD. products meet the requirements of Directive 2011/65/EU on the restriction of hazardous substances.

Changes or modifications not expressly approved by the responsible party could void the user's authority to operate the equipment.

ISEDC Radiation Exposure Statement: Complies with ISEDC RF radiation exposure limits for uncontrolled environments. Transmitter must not be co-located or operating with any other antenna or transmitter. Install and operate with minimum 20cm distance between radiator and body.

Radio Equipment Directive: CE Hereby, INMOTION TECHNOLOGIES CO., LTD. declares that the radio equipment type is in compliance with Directive 2006/42/EC.

17. Contact US

Contact INMOTION TECHNOLOGIES CO., LTD. for issues related to riding, maintenance, safety, or errors/faults.

Address: 18/F, B1, Nanshan i Park, No.1001 Xueyuan Ave., Nanshan, Shenzhen, China

Tel: 4000100012 ext.8015

E-mail Service: service@imscv.com

E-mail Amazon USA Service: AmazonService@imscv.com

Website: www.inmotionworld.com

INMOTION App: Me → Online Service.

NOTE: Have your scooter serial number ready when contacting INMOTION. Find it on the deck or in the App under "Vehicle Management" → “About Vehicle”.