Welcome!
Models: S1, S1G
Thank you for choosing the Inmotion Electric Scooter S1 (hereinafter referred to as scooter). This scooter is easy to fold and easy to carry. It is also a sports entertainment equipment with stylish technology.
Safety Instructions
The electric scooter S1 is designed for personal urban transportation and carries inherent safety risks, similar to all transportation means.
- Follow the tips and warnings in this manual to reduce risks, but they cannot eliminate all risks. You may be at risk of injury or death due to loss of control, collision, and falls.
- The scooter is suitable for hard pavement. Use in closed pavement environments (e.g., communities, parks, special venues). Avoid places with obstacles and contacts. Be vigilant and slow down in unfamiliar environments.
- Always wear a helmet and protective gear (approved bicycle or scooter helmet).
- For the first ride, avoid areas with children, pedestrians, pets, vehicles, bicycles, or other obstacles.
- Respect pedestrians, especially the elderly, children, disabled, and pregnant women. Remind pedestrians when approaching from behind and slow down. Abide by local traffic laws and regulations.
- In regions without electric scooter laws, strictly follow the safety requirements for cyclists in this manual. Inmotion is not responsible for property loss, injury, or legal disputes caused by violating safety tips.
- Before lending your scooter, ensure the borrower has read the manual, watched the instructional video, and learned novice instructions. You are responsible for new riders' safety. Assist them until they learn basic operation. Ensure they wear helmets and protective gear.
- Before riding, check for loose fasteners and damaged parts. If the scooter makes abnormal noise or alarm sounds, stop using it immediately and consult your dealer or manufacturer (service@imscv.com).
- Observe the road surface, avoid obstacles and uneven ground (wet, loose sand, stone, ice).
- Read and follow all "Caution" and "Warning" notices. This product is suitable for users aged 14-60 years old and weighing less than 140kg.
Users not suitable for riding:
- Persons affected by alcohol or drugs.
- Persons unable to engage in vigorous physical activities due to illness.
- Individuals unable to maintain balance.
- Persons whose weight exceeds the prescribed limit (refer to "Model Parameter Table").
- Pregnant women.
Additional Safety Tips:
- Minors require adult supervision.
- Abide by local laws and regulations; do not ride in prohibited areas.
- Ensure you can see the area in front and be seen by others.
- Do not ride in snowing, raining, slippery, muddy, or icy conditions. Avoid obstacles like sand, stones, or roadblocks.
- Damages from water ingress are not covered by warranty.
- Do not drive at night.
- Avoid sudden acceleration or deceleration. Do not exceed the scooter's speed limit.
- Do not charge when the charging port, charger, or power outlet is wet.
- Use only original Inmotion chargers.
- Use only Inmotion-approved parts and accessories. Do not modify the scooter, as it may affect operation and void the warranty.
- Children should not use scooters or play with parts.
- Park on flat, solid ground. On a slope, the kickstand must face downhill to prevent overturning. Ensure stability after parking. Avoid parking in busy areas; park near a wall if possible.
- Regular maintenance is recommended for a better driving experience.
- Read the user manual before charging.
- Do not touch brake parts, as injury may occur.
Packing List
Please carefully check if the items in the packing box are complete and intact. If any part is missing or damaged, please contact your point of purchase or email manufacturer (service@imscv.com).
Included Items:
- User Manual
- Unboxing Instruction Manual
- Power cable
- Power adapter
- Extended air valve
- Screws (x7)
- Allen wrench
- Gland Screw (x1)
- Lid
- Clamp
- Rubber Plug (x2)
- Bearing (x2)
- Folding ring
Product Function Diagram
The scooter includes the following components:
- Handlebar Area: Bell, Throttle, Headlight, Dashboard, Brake Handlebar, Handlebar, Folding ring.
- Frame & Body: Mast, Folding Hook, Footrest, Folding parts, Front suspension, Front-fender, Front wheel, Rear-fender, Taillight, Plate, Rear disc brake, Rear wheel, Kick-stand, Charging ports.
Dashboard & Power on/off
The dashboard provides information and controls:
- Bluetooth display: Icon indicates connection to a mobile device.
- Power display: Shows remaining battery via 5 horizontal bars.
- Speedometer: Displays the current speed of the scooter.
- Turning arrow: Lights up for left or right turns.
- Start button: Long press (3s+) to turn ON/OFF. Single click to toggle headlights. Double-click to switch driving mode.
- Pushing-assist mode: Facilitates pushing the scooter by walking.
- Headlight display: Indicates if the headlight is ON/OFF.
- Sport mode (S): Powerful mode for experienced riders.
- Standard mode (D): For common commuting, suitable for familiar riders.
- Energy-saving mode (ECO): For beginners.
- Error display: Icon lights up when a fault occurs; stop using the scooter. The icon disappears after the fault is removed.
Scooter Assembly
Assembling Accessories List: Screws (x7), Gland Screw (x1), Stem Hook (x1), Screw Wrench (x2), Rubber Plug (x2).
Assembly Steps:
- After opening the package, check all accessories against the list. If parts are loose, arrange them as shown.
- Keep the vehicle body fixed. Attach the front fork part to the stem tube. Assemble the screw and insert it using the screw wrench. Do not overtighten initially; you can tighten it after adjusting the handlebar.
- Adjust the handlebar and dashboard. Ensure the side with the light faces forward. Place the scooter on its kickstand. Align the handlebar and rear wheel. Tighten the Gland Screw. Fasten the screws below the folding parts.
- Unfold the scooter by pulling up the stem. Route the cable inside the tube. Check if the handlebar moves smoothly. Insert the two rubber plugs into their correct upper and lower holes.
- Put back the stem and lock the folding wrench. Check if the scooter powers ON/OFF normally.
- Fasten the 5 screws to fix the handlebar (2 on the sides, 1 in the middle back of the stem).
- Lock the stem hook with 2 screws, ensuring the longer part of the hook points upward.
- Before riding, fasten all screws mentioned and check if power ON/OFF and other functions work normally.
Initial Use
There are safety risks when using scooters. Before initial use, users must carefully read the safe driving guide through the APP. For safety, the new scooter is not activated and will provide intermittent beep prompts after booting. Before activation, the speed is very low and functions are limited. You need to install the Inmotion App on your mobile device (Bluetooth 4.0 and above), connect your scooter via Bluetooth, and activate it as prompted by the APP.
Scan the QR code to download the Inmotion App.
- Install the Inmotion App on Android or iOS devices, register, and log in.
- When the scooter is turned on, Bluetooth enters waiting connection mode by default. Connect the scooter with the APP. The Bluetooth icon remains on once connection is successful, allowing app operation.
- Follow the app prompts to activate the scooter and learn safe driving. You can then start using your scooter and check its status and functions via the APP.
Connect the charger
Steps: Open the cover of charging ports and plug in the charger. Cover back after charging.
Warning: Use the original charger, otherwise the battery may be damaged or cause danger! Do not connect the charger when the charging port or charging cable is wet! If the battery is damaged or gets into water, it is forbidden to charge or continue to use the battery!
How to Ride
Please take safety measures when riding, such as wearing sports clothes, helmets, knee pads, elbow pads, and other protective tools.
- Long press the power ON/OFF button until the ring lights are fully illuminated. Check the battery indicator. If the remaining battery is too low, please charge immediately.
- Stand on the footrest with one foot, and use the other foot to push off the ground to begin gliding. The motor can only be started after the vehicle speed reaches 3km/h. Gently press the throttle on the right handlebar to ride slowly. Hold the handlebar to control the riding direction (similar to riding a bicycle).
- Gently press the throttle on the right handlebar to accelerate, but do not go too fast. Hold the brake to slow down (try to avoid emergency braking). When the scooter stops or taxis slowly, get down one foot first, then dismount normally.
Note: To avoid accidental touch, by factory default, the motor and throttle will start only when the scooter is in the "taxi state", and the throttle does not work after the scooter stops.
Potential Safety Hazards
⚠️ Failure to follow these instructions may result in serious injury.
- Avoid riding in the rain.
- Do not ride at high speed when passing bumps and potholes; it's recommended to keep a slow to medium speed (5-10km/h) on rough roads.
- Do not press the throttle when pushing the scooter.
- Pay attention to road conditions and avoid obstacles while riding.
- Avoid hitting high obstacles such as door frames and elevators.
- Do not step on the rear fender.
- Do not hang heavy objects on handlebars and other parts of the scooter.
- Do not ride in non-standard postures, such as riding with one foot on the footrest or one hand on the handlebar.
- Do not ride in public streets if not allowed by law.
- Do not turn the handle greatly during high-speed riding.
- Do not touch the motor if it causes high temperature and heat during operation.
- Do not ride hands-free from the handlebars.
- Do not go straight through puddles; please go around them at a low speed.
- For one rider only; do not ride with another person or holding a child. Not suitable for pregnant women.
- Do not ride scooters up and down steps or jump obstacles.
- Do not use a cell phone or headphone while riding.
Folding and Carrying
To Fold: Power off the scooter. Hold the mast with one hand, and with the other hand, press the fold-unlock button and pull back the folding wrench. Then fold the mast backward. After folding down the mast, press down the folding ring, align it with the hook on the rear end of the footrest, and release the folding ring to hook it successfully.
To Unfold: Press down the mast, at the same time hold the folding ring until it releases from the hook, and straighten the mast to ensure the folding wrench locks back into its position tightly.
You can carry the scooter after folding.
Daily Care and Maintenance
Cleaning and storage
Wipe the main frame of the scooter with a soft damp cloth. For stains difficult to clean, brush repeatedly with a toothbrush and toothpaste, then clean with a soft damp cloth. Tips: Do not use alcohol, gasoline, kerosene, or other corrosive, volatile solvents to clean your scooter, as these may damage the appearance and internal structure. It is forbidden to spray the scooter with a pressure water-gun or water pipe.
Warning: Before cleaning, ensure the scooter is powered off, the charging cable is unplugged, and the rubber cover of the charging port is fastened. Otherwise, it may cause damage to electronic components or the battery. When the scooter is not in use, place it in a bright and dry place. Do not park the scooter outdoors. Sun exposure or extreme temperature conditions (overheating and too cold) will accelerate the aging of plastic parts and may reduce battery life.
Battery dis-assembly and maintenance
Do not remove the battery unless necessary, as it is complicated and may affect scooter operation. It is best to let a professional install tires. Improper operation may cause instability or other failures.
- Do not use batteries from unauthorized third parties; this may pose safety risks.
- Recharge the scooter with the original charger; otherwise, there may be a risk of damage or fire.
- Do not touch battery contacts, or disassemble/pierce the battery case. Avoid short circuits caused by metal objects touching contacts, which may cause battery damage or personal injury.
- Do not put the battery into fire, as it may cause failure, overheating, or fire.
- Fully charge the scooter before storing it to prolong battery life. Do not exceed the specified temperature limits (refer to the parameter table) while storing and charging.
- Improper disposal of used batteries can seriously pollute the environment. Comply with local regulations when disposing of the battery.
A battery in good condition can maintain performance over many miles. Recharge the battery on time to avoid complete drainage. At 22°C, the battery has optimal life and performance. At temperatures below 0°C, battery life and performance may degrade. Check the Inmotion APP for more information.
Reminding & Warnings
Reminding: Please do not try to disassemble the battery, as there is a risk of fire. Users are not allowed to repair parts without authorization.
Warning: Please do not try to disassemble the battery, otherwise there is a risk of fire. Users are not allowed to repair the parts contained in this scooter by themselves, if without authorization.
Warning: Do not ride this scooter when the ambient temperature exceeds the product operating temperature (refer to parameter table). Low/high temperatures can cause power loss, slipping, or falling, resulting in personal injury or property damage.
For product maintenance, repair, and other related questions, please contact your point of purchase or email service@imscv.com.
Specification
Specification | Value | |
---|---|---|
Dimension of Product | Unfold: L*W*H | 1307*520*1275mm |
Fold: L*W*H | 1307*520*560mm | |
Weight | Net weight | Approx. 24kg |
Recommendation | Max. of Payload | 140 kg |
For Age at | 14+ year | |
For height at | 130-200cm | |
Performance | Max. of Speed | S1: 30km/h; S1G: 20km/h |
Mileage[1] | Approx. 95km | |
Max. of Slope | Approx. 30% | |
Working temperature | -10–40°C | |
Storage temperature | -20–45°C | |
IP rating | IP55 | |
battery | Charging time | Approx. 7h (single charges), Approx. 3.5h (Dual chargers) |
Rating Voltage | 54V | |
Max. of Voltage | 63V | |
Charging temperature | 0–40°C | |
Capacity | 675Wh | |
BMS | Overheat / short circuit / overcurrent / overcharge protection | |
Motor | Rating power | 500W |
Charger | Input Voltage | AC100-240V 50/60HZ |
Output Voltage | DC63V | |
Output Current | 1.8A | |
Tyre | Front / Rear | 10" Pneumatic tire, tubeless |
Others | brake light | LED taillight |
Turning light | Sensor-activated automatically | |
Ride modes | Eco- mode, D-mode, S-mode |
[1] Mileage: Tested under full power, 75kg load, 25°C, riding at a cruising speed on a flat road at 18km/h.
Trademarks and Legal Notices
Inmotion is a registered trademark of Inmotion Technologies Co., Ltd.; Android is a trademark of Google; App Store is a sign of Apple service; other trademarks mentioned are owned by their respective owners. This manual includes function introductions and instructions. Due to continuous product improvement, it may differ slightly from your purchased product. Please scan the QR code on page 6 to download the latest version of the manual for Android or iOS devices. Product updates may cause deviations in color and appearance; refer to the actual product.
All rights reserved by Inmotion Technologies Co., Ltd.
Manufacturer: Inmotion Technologies Co., Ltd.
The more familiar you are with the scooter, the safer your riding will be. We suggest you:
- Read this user manual carefully before riding.
- Do not allow others to ride this scooter before they read this manual carefully.
- Be aware of and strictly comply with all relevant laws, regulations, and policies regarding riding scooters in your area.
Safety instructions we suggest you to:
- Wear a helmet of appropriate size when riding.
- This scooter may contain detachable parts; keep them away from children to prevent swallowing.
- Scooters are similar to other sports equipment; exercise caution. Ensure you can ride freely without assistance before riding. Do not ride while fatigued, under the influence of drugs or alcohol. Do not ride during illness, pregnancy, or when experiencing negative emotions. No racing or overloading.
- If the scooter exhibits damage, emits odor, smoke, overheating, or performance failure, discontinue use and contact after-sales service.
- If smoke is emitted (even with low probability), immediately move the scooter to an empty area or attempt to cool it down. Prevent damage to property or personal injury.
- Scooters are not medical devices and are not recommended for use as medical aids.
- Do not throw or drop the scooter. Do not place it near open flames or high temperatures.
- The scooter may move spontaneously if parked without turning off, potentially causing damage to others or property.
- Unauthorized modification may endanger your safety; do not modify the scooter without permission.
The requirement of environment for riding:
- Do not ride on inclined roads, uneven ground, slopes greater than 30%, near swimming pools, or in slippery areas with stagnant water or debris. Do not ride in areas prohibited by local laws.
- For your safety, do not ride through terrains you have not encountered before, such as steep slopes or inclined roads.
- Do not ride in bad weather, low visibility, at dawn, dusk, thick fog, thick smoke, at night, or when extremely fatigued, as these conditions increase accident risk.
- Do not ride in rain or snow. After riding, park the scooter indoors to prevent water ingress damage. Be aware that wheel resistance is reduced on wet roads, making speed control more difficult.
The requirement to rider:
- Riders must be over 14 years old and weigh no more than 140 kg. Parents or guardians are responsible for their minor children's activities and safety and should accompany them.
- Not recommended for individuals with sight, hearing, body, or movement difficulties. Those with serious heart conditions, high blood pressure, dizziness, or other diseases unsuitable for sports should not ride. Do not ride after taking drugs or alcohol.
Preparation before riding:
- Please read this manual carefully. Ensure all components are correctly installed and not too loose or too tight to avoid damage or failure.
- Before riding, check installation status, wheel performance, and battery status. Ensure the scooter is in proper condition with no signs of loosening or damage. If any abnormality is detected, stop riding immediately and contact after-sales service.
- The scooter may not maintain normal riding power when the display is low or empty. Ensure sufficient power before riding to avoid danger.
- Wear a helmet. Knee pads, gloves, wrist guards, elbow pads, and sports shoes are recommended.
- Do not wear high heels, slippers, or open-toed shoes when riding.
- Wearing protective glasses is recommended to shield your eyes from dirt, dust, and insects.
Notes on riding:
- Please comply with local laws, regulations, and policies on riding.
- Start smoothly on a flat road. Do not accelerate or brake sharply. Always hold the handle with both hands.
- Be vigilant and maintain good judgment. Keep a suitable speed and safe distance from other vehicles. Slow down when entering unfamiliar environments.
- To avoid distraction, do not wear headphones or earplugs, make phone calls, or take pictures while riding.
- Be defensive on the road. Pay attention to yourself, vehicles, and pedestrians.
- Ensure you are visible to others while riding.
- One rider only. Do not ride with others on one scooter, including children and pregnant women.
Battery maintenance and storage
- Use the original battery. Do not use batteries from unauthorized suppliers due to safety risks.
- Use the original charger; otherwise, the battery may be damaged or pose a fire hazard.
- The battery contains harmful substances; do not attempt to damage or disassemble it.
- If the battery is damaged or submerged in water, do not recharge or continue to use it.
- Do not plug in the charger when the charging port or charging cable is wet.
- It is strictly forbidden to disassemble, squeeze, or puncture the product. Do not touch battery contacts, disassemble, or pierce the casing. Do not immerse the product in water or fire (including near heat sources). Avoid short circuits.
- It is strictly forbidden to immerse the battery and scooter in water or ride in the rain. Do not clean the scooter with high-pressure hoses. If exposed to heavy rain, wipe with a dry soft cloth, stop using immediately, and consult service staff.
- Do not place the scooter in environments below -20°C or above 45°C (e.g., in a car exposed to summer sun). Before charging, if the battery was stored below 0°C, place it in a warm environment (above 10°C) until it reaches the charging temperature requirement (0-40°C).
- Warning: Improper use may attenuate battery performance or render it unusable, which is not covered by warranty.
- Improper disposal of used batteries can pollute the environment. Comply with local laws and regulations.
Others
- The data and parameters of the scooter may vary with different models and are subject to change without notice.
- To the extent permitted by law, Inmotion reserves the right to interpret and explain this statement, which is governed by the laws of the People's Republic of China. Inmotion is not liable for compensation for damages or losses. Riders bear their own responsibility for unforeseen risks.
Thank you again for your choice and trust in Inmotion.
Warranty
Thank you for purchasing Inmotion products. Please consult the warranty policy with your purchasing point. For any assistance needed, please email service@imscv.com.
Download Inmotion App
Scan the QR code to download the Inmotion App. Version: V1.0