Installation Manual
Round Shower Head Set
For Model Code: 8562, 8562-2, 8562-3, 8560-2 (In different shower heads only)
Parts List
| No. | Description | Quantity |
|---|---|---|
| 1 | Connector | x 1 |
| 2 | Main Body | x 1 |
| 3 | Decoration Cover | x 1 |
| 4 | Shower Holder | x 1 |
| 5 | Handheld Shower | x 1 |
| 6 | Shower Head | x 1 |
| 7 | Shower Hose | x 1 |
| 8 | Grease Oil Pack | x 1 |
| 9 | Teflon Tape | x 1 |
| 10 | Allen Key | x 2 |
| Spare Parts: | ||
| 11 | Spare M5 Grab Screws | x 4 |
| 12 | Spare Shower Hose Rubber Washer | x 1 |
| 13 | Spare O-Rings For Connector | x 3 |
| 14 | Spare M7 Screws for Shower Holder | x 2 |
Diagram Description: An illustration shows the various components of the shower head set laid out, including the main shower body, a separate shower head, a handheld shower unit, a flexible hose, a wall connector, a shower holder arm, screws, an allen key, a packet of grease, and a roll of teflon tape.
Instructions
- Working pressure: 0.05-1 Mpa, Working temperature: 0-55°C.
- Products are manufactured as per standard AS/NZS 3662:2005, as per Australian standard, and with WaterMark & WELS certificate as shown in the packing.
- All surfaces should be cleaned with water or mild liquid detergent. Do not use cream cleaner or citrus based or chemical cleaning products.
Warranty Terms
- 5 years guarantee against main body finishing and Cartridge.
- 2 years guarantee on washers and O-rings.
Installation Steps
Step 1: Prepare Water Supply Outlet
Water supply outlet G 1/2"
Should wrap enough teflon tape over the water supply outlet.
Diagram Description: Illustrates a threaded pipe fitting representing the water supply outlet, labeled "Water supply outlet G 1/2".
Step 2: Attach Connector
Screw the connector to water supply outlet and tighten firmly by spanner.
Diagram Description: Shows a plumbing connector fitting, designed to screw into the water supply outlet.
Step 3: Attach Shower Holder to Main Body
Plug the shower holder onto the main body and tighten it firmly by 2 M5 grab screws.
Diagram Description: Depicts the shower holder (part 4) being attached to the main shower body (part 2) using two screws, labeled 'M5 x 1'.
Step 4: Install The Rail (Main Body Assembly)
Very Important:
- Smear the grease oil on the connector O-rings. Do not wrap teflon tape over the O-rings.
- To avoid connector O-rings being scratched by screw tips and causing water leakage, the screws must be loosened enough before plugging the main body onto the connector.
- Gently plug the main body onto the connector and tighten it firmly by 2 M5 grab screws.
Diagram Description: Shows the main shower body assembly being connected to the water supply connector. It indicates the use of two M5 screws for securing the connection and highlights the importance of proper O-ring lubrication and screw handling.
Step 5: Attach Shower Head to Arm
Make sure washers and flow restrictor are shown inside the shower rose. Screw shower rose to arm.
Diagram Description: Illustrates the shower head being screwed onto the shower arm. It points out the placement of a 'Rubber Washer' and a flow restrictor within the shower rose.
Step 6: Connect Handheld Shower to Hose
Make sure washer is shown into shower hose. Please note that the conical nut should be connected to the handheld shower, the hex nut should be connected to the shower rail.
Diagram Description: Shows the handheld shower unit being connected to the flexible shower hose. It highlights the placement of a 'Rubber Washer' and specifies that the conical nut connects to the handheld shower, while the hex nut connects to the shower rail.
