Pyle PT-1100 / PT-3300 Operating Manual
Thank you for purchasing this fine PYLE PRO amplifier. Please read this operating instructions carefully before using. It will acquaint you fully with all its features and help you enjoy your time.
The product adopts the most advanced digital technique in the world. It is 4 channels with its high power output, the real acoustic centre of your family movie theatre. It is designed to be multi-functional with microphone input jacks. It is a product of the finest accompanying acoustic amplifier, when applied to TUNER, TAPE, AUX, DVD/CD etc.
Features
- Power 4 loud speaker
- Inputs: RCA (4 audio sources)
- Two Microphones Input Jacks
- Master Volume Controls w/Blue LED's
- Heavy Duty Fan Cooling
- A/B Speaker Selector
- Removable rack-mount brackets
- 3U Height w/Remote
- 110-220V Switchable
- 1 RCA dedicated for record line output
Precautions
- Power source: The unit should be connected to a power supply AC~110/60Hz or AC~220V/50Hz.
- Ventilation: The unit should be situated so that its location or position does not interfere with its proper ventilation. Place the unit at least 10cm away from the wall.
- Water and moisture: The unit should not be used near water, for example, near a swimming pool or in a wet basement, etc.
- Electric shock: If a metal object, such as a hairpin or needle, comes into contact inside this unit, a dangerous electric shock may result. For families with children, never permit children to put anything, especially metal, inside this unit.
- Enclosure removal: Never remove the enclosure. If the internal parts are touched accidentally, a serious electric shock might occur.
- Abnormal smell: If an abnormal smell or smoke is detected, immediately turn the power OFF and pull out the power cord. Contact your dealer or nearest service station.
Technical Specifications
| Technical | PT-1100 | PT-3300 |
|---|---|---|
| Main Channel Power Output PMPO,8 Ohms, 1KHz test | 1000WX2 | 3000WX2 |
| THD(1KHz) | <1% | <1% |
| Normal Load Impedance | 8 Ohm | 8 Ohm |
| Input Sensitivity Impedance CD/DVD AUX TAPE TUNER | 400mV/33k Ohm | 400mV/33k Ohm |
| Microphone | 6mV/600 Ohm | 6mV/600 Ohm |
| Signal to Noise Ratio | 78dB | 78dB |
| KARAOKE | 76dB | 76dB |
| Frequency Range Frequency Response(20Hz-20KHz) | ±2dB | ±2dB |
| Tone Characteristic(100Hz-10KHz) | ±10dB | ±10dB |
| Power Requirements | AC~110V/60Hz AC~220V50Hz | AC~110V/60Hz AC~220V50Hz |
| Dimension | 483(W)X300(D)X140(H)mm | 483(W)X300(D)X140(H)mm |
| Weight | 6kg | 6.5kg |
Specifications subject to change without prior notice
Front Panel Description
The front panel features the following controls and indicators:
- 1. Power Switch
- 2. Input Source Selector
- 3. Bass Control
- 4. Treble Control
- 5. Balance Control
- 6. Speaker (A+B) Selector
- 7. Speaker (A/B) Selector
- 8. VFD Display
- 9. Microphone Echo Control
- 10. Microphone Bass Control
- 11. Microphone Treble Control
- 12. Microphone Volume Control
- 13. Master Volume Control
- 14. Microphone Input Jack
NOTES: Speaker (A/B) Selector means you can choose one of the speakers. Press Speaker A+B Selector means you can choose both A and B speakers. When you turn on the power, we set you have choosed both A and B speakers.
Rear Panel Description
The rear panel provides the following connections:
- 1. TAPE Input (RCA)
- 2. TUNER Input (RCA)
- 3. DVD/CD Input (RCA)
- 4. AUX Input (RCA)
- 5. Record Line Output (RCA)
- 6. Speaker A (RIGHT) Output (Banana Jacks)
- 7. Speaker A (LEFT) Output (Banana Jacks)
- 8. Speaker B (RIGHT) Output (Banana Jacks)
- 9. Speaker B (LEFT) Output (Banana Jacks)
- 10. Cooling Speed Fan
- 11. Voltage Selector 110-220V
- 12. AC Power Cord Jack
Remote Controller Operation
The remote controller should be operated within 6 meters and a 30° scope in front of the receiver. Make sure there is no big obstacle between the remote controller and the machine. The remote sensor should be far away from bright light, as high amounts of light can affect its performance.
The remote control has the following functions:
- 1. SPEAKER Speaker (A/B) Selector
- 2. SPEAKER Speaker (A+B) Selector
- 3. DVD/CD Selector
- 4. AUX Selector
- 5. TUNER Selector
- 6. TAPE Selector
- 7. VOL+ (Master Volume Up)
- 8. VOL- (Master Volume Down)
Typical Output Hook-Up Diagram
The diagram illustrates how to connect speakers and audio sources to the amplifier.
Connections:
- AUDIO INPUT: Connect TAPE, TUNER, DVD/CD, AUX sources to the corresponding RCA inputs.
- RECORD LINE OUT: Connect to a recording device.
- SPEAKERS OUTPUT: Connect Main (A) Speakers and Main (B) Speakers to the respective outputs using banana jacks. Ensure correct polarity.
- Microphone Inputs: Connect microphones to the 2 MIC INPUTS.
Safety Instructions:
- Make sure that all connections are properly connected and the main volume is set to minimum level before turning on the unit.
- When more than one pair of speakers are used, especially the main speaker output, make sure that the speakers used are of the same wattage and impedance, otherwise the unit may be damaged under high power or long term operation.
- To avoid humming sounds and unwanted noise, make sure that all the wires are properly inserted.
- For speaker cords, strip off the vinyl coating and twist the wire tip. Push down the pink jack or loosen the screw terminal, before inserting the wire tip, then fasten it and tighten the screw. Be careful not to let the wires stick out of the terminal otherwise this may cause a short circuit when wires of different terminal contact each other.
- After the unit is turned on, adjust the main volume to the desired level. The same is true with the bass and treble volume, etc.
