Jasion X-Hunter E-bike LCD Display Controls and Settings
Display and Settings Overview
The LCD display on the Jasion X-Hunter e-bike provides essential information and control over various functions. Key elements include:
- Display Backlight: Controls the brightness of the display.
- Error: Indicates when a fault is detected.
- Power Level: Shows the remaining battery life.
- Speed: Displays current speed, average speed (AVG), and maximum speed (MAX).
- Speed Unit: Can be set to Km/h or MPH.
- Speed Mode: Refers to the display of average speed, maximum speed, and real-time speed.
- Riding Information: Includes TRIP (distance for a single trip), ODO (total odometer reading), TIME (riding duration), and POW (power usage).
- Pedal Assist Level: Ranges from 1 to 3 (or 1 to 5), indicating the level of motor assistance.
LCD Display Controls
The following table outlines the operations and their corresponding directions:
| Operation | Directions |
|---|---|
| Turn on bike | Press and hold the power button (1) until power engages. |
| Turn off bike | Press and hold the power button (1) until power off. The display will automatically turn off if inactive. |
| Increase pedal assist (PAS) level | Press the '+' button (2). |
| Decrease pedal assist (PAS) level | Press the '-' button (3). |
| Increase backlight | Enter advanced setting - P01. Adjust between levels 1 (darkest) and 3 (brightest). |
| Toggle speed mode | In the power-on state, press the power button (1) once to cycle through TRIP, ODO, TIME, POW. |
| Turn on walking mode | Long press the '-' button (3) to activate walking mode at 6 km/h. Release to exit. |
| Turn on headlight | Press the headlight button (4) once. |
| Activate Electric Bell | Press the bell button (5) once. |
| Restore factory settings | Enter advanced setting - P16. Hold the '-' button (3) for 5 seconds. |
LCD Display Operations and Settings
Setting Mode: To enter Setting Mode, long press the power button (1) and '+' button simultaneously for 3-4 seconds. Short press the power button (1) or '+' button to choose a set-up item. The parameter will flash while setting. Long press the power button (1) to confirm and exit, stopping the parameter from flashing.
Saving Parameters: Short press the power button (1) to switch to the next parameter, saving the current one. Pressing the '+' button exits the setting and saves parameters. If no action is taken, the display automatically exits and saves modified parameters after 8 seconds.
Parameter Settings:
- P01: BACKLIGHT: Adjust backlight level from 1 (darkest) to 3 (brightest).
- P02: Unit of Mileage: Set to 0 for KM or 1 for MILE.
- P03: Voltage level: Select 24V, 36V, or 48V (default is 36V).
- P04: Dormancy time: Set dormancy time from 1 to 60 minutes (0 means no dormancy).
- P05: PAS levels: Configure for 0 (3 PAS levels) or 1 (5 PAS levels).
- P06: Magnet sensor setting: Do not change.
- P07: Throttle setting: Do not change.
- P08: Power assist sensor setting: Do not change.
For advanced settings from P06 to P20 (excluding P16), contact Jasion Support at support@jasionbike.com for guidance to avoid errors.
PAS Adjustment
To adjust the PAS level:
- Simultaneously press and hold the power button (1) and '+' button for 3 seconds to enter settings mode.
- Press the power button (1) to navigate to P05 for assist level adjustment.
- The assist level is displayed in the lower right corner.
PAS Levels:
- 3-speed mode: Level 1 (2V), Level 2 (3V), Level 3 (4V).
- 5-speed mode: Level 1 (2V), Level 2 (2.5V), Level 3 (3V), Level 4 (3.5V), Level 5 (4V).
If your bike has only three PAS levels, it might not be set correctly at the factory. To adjust to 5-speed mode, short press the '+' button to change the lower number from 0 to 1.
To enter the PAS level adjustment, press and hold the '+' and '-' buttons for 3 seconds. Use the '+' and '-' buttons to adjust the level (range 1-5). Press and hold the power button (1) and '+' button to save and exit.
Unlock Speed
To adjust the speed limit:
- Simultaneously press and hold the power button (1) and '+' button for 3 seconds to enter settings mode.
- Press the power button (1) to navigate to P08 for speed adjustment.
- The current speed is displayed in the lower right corner.
- Short press the '+' button to increase speed and the '-' button to decrease speed. The speed range is 0-100 km/h. Set to 100 for maximum speed.
- Simultaneously press the power button (1) and '+' button to save and exit. Parameters are saved automatically after 8 seconds if no action is taken.
FAQs
- Q1: What if the e-bike arrived missing accessory or broken part?
- A1: Please take a photo and email it to support@jasionbike.com. Jasion Support Team will respond and send the correct accessory or part replacement.
- Q2. Will my bike arrive assembled?
- A2: Your bike will arrive mostly assembled. Tools and a comprehensive assembly video will be provided for the remaining parts.
- Q3. What can I do if something goes wrong with my e-bike during the warranty?
- A3: Please contact Jasion Support in time. Describe the problem in detail and provide photos/videos with your order ID for prompt assistance.
Error Codes
| Error Code | Status |
|---|---|
| 00 | Normal status |
| 33 | Current issue |
| 34 | Throttle issue |
| 35 | Power motor issue |
| 36 | Power motor signal issue |
| 37 | Braking lever issue |
| 30 | Communication issue |
