UHPPOTE HBK-R01 Remote Control

Thank you for choosing the HBK-R01 remote control provided by UHPPOTE.

Precaution

For avoidance of damage to the product or injury to people, please carefully read this manual before use and keep it for further reference.

Warnings:

• For avoidance of damage to the product, do not expose the product to rain or damp.
• This product is only for indoor use.
• Please use a combination of transmitter and receiver provided by UHPPOTE as we can't guarantee our transmitters or receivers are fully compatible with other manufacturers' products.
• The product installation shall be conducted by a professional electrician as it requires specialized knowledge. Incorrect operation may damage the product, or make it inoperable.
• The transmitter and receiver have been paired with each other in the factory.
• Keep this product away from children under 3 years old to prevent ingestion.
• Install the receiver in a place out of reach of children, so as to prevent electric shock.
• Please do not put the battery in water, fire, or moisture places for avoidance of explosion.
• The battery contains hazardous substance. Return the waste batteries to the recycling bin to avoid contamination to the environment.

Features

• Specialized for the access control system and unable to be applied to other fields.
• Support connecting external access control keypad. (Remarks: Access control keypad is excluded.)
• Built-in buzzer makes sound to remind people when the door is locked or unlocked.
• Built-in diode, real-time protecting electric lock, prolonging the service life.

HBK-R01 REMOTE CONTROL

Receiver and Transmitter Diagram:

The diagram shows two main components: a smaller remote transmitter and a larger receiver unit. The receiver unit has ports labeled 'ACCESS KEYPAD', 'EXIT BUTTON', and 'LOCK'. It also features indicator lights, a buzzer, and controls for 'LOCK TYPE' (NO/NC) and 'RF'. The transmitter is a simple handheld device.

Specifications

Receiver

Transmitter

Wiring Diagram

1) Connect Fail-Secure Lock

This diagram illustrates the wiring for a fail-secure lock. It shows connections between an Access Keypad, the HBK-R01 receiver unit, an Exit Button, and the Fail-secure Lock. Key connections include power (+12V, GND), data (PUSH, COM), and lock control (NO/NC terminals on the receiver).

2) Connect Fail-Safe Lock

This diagram illustrates the wiring for a fail-safe lock. Similar to the fail-secure setup, it shows connections between the Access Keypad, HBK-R01 receiver, Exit Button, and the Fail-safe Lock. The difference lies in the connection to the 'NC' terminal for a fail-safe configuration.

Operating Settings

1) Remote Pairing

Tap the RF icon followed by pressing the button on the transmitter within 20 seconds.

2) Unpairing

Tap and hold the RF icon for 5 seconds. Remarks: This operation will clear all paired transmitters; please operate with caution.

3) Lock Type Setting

NO: Fail-Secure Lock

NC: Fail-Safe Lock

Remarks: Incorrect setting will affect the operation of the lock; please confirm the lock type before setting.

4) Buzzer Setting

ON: Enable.

OFF: Disable.

5) Operating Mode Select

Momentary: Press button A for ON, Release button A for OFF.

Latched: Press button A for ON, press button B for OFF.

Toggle: Press button A for ON, press button A again for OFF. Remarks: Latched is only valid when using a transmitter with 2-buttons.

6) Time Delay Setting

Support 0/5/10 seconds time delay. Remarks: Only available when Momentary is selected.

Trouble Shooting

1. Q: Why does not the transmitter's LED light up when I press the button on it?

   A: The battery power may be exhausted. Please replace the battery.

2. Q: Why can't the lock be unlocked after pressing the transmitter?

   A: Please check the issue by the following steps:

   • a. Check whether the remote control receiver and transmitter are paired successfully.
   • b. Check whether there is any metal object around the remote control receiver as it may shield the signal.

3. Q: Why can't the lock work properly when the wiring is correct?

   A: Please check whether the indicator of the receiver is on and the mode of lock is selected correctly. (For more details, please refer to 'Lock Type Setting' in this manual.)

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• -- Reorient or relocate the receiving antenna.
• -- Increase the separation between the equipment and receiver.
• -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• -- Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.