Paul Neuhaus Q Smart Home Lights

Product Details

Model Number: 833604

Power Supply: 230V / 50Hz~

Light Source: 1x LED-Board 55V DC / 58W (not replaceable)

Wireless Connectivity: 2.4 GHz, 10 dBm

Specifications:

• Power Consumption: 58 W
• Luminous Flux: 5,800 lm
• Secondary Spec: 65 W, 2,600 lm
• Lifespan: 20,000 hours
• Color Temperature: 2,700 - 5,000 K
• Switching Cycles: 15,000
• Dimming: Dimmable with radio remote control

Included in Package:

• Radio remote control
• 2x AAA, 1.5V batteries
• Mounting hardware: 2x wall plugs, 2x screws, 1x mounting plate

Certifications: CE [WEEE symbol]

Step 1: Mounting / Fitting

This section describes how to install the light fixture as a ceiling light.

Procedure:

1. Prepare Wiring: Connect the electrical wires to the terminal block. Ensure wires are inserted correctly into the screw terminals and securely tightened. The terminal block has designated connection points for live (L), neutral (N), and potentially ground wires.
2. Prepare Ceiling Mount: Drill holes in the ceiling, approximately Ø8mm, for the mounting hardware.
3. Attach Mounting Plate: Secure the provided mounting plate to the ceiling using the supplied screws and wall plugs.
4. Suspend Light Fixture: Attach the three suspension wires of the light fixture to the mounting plate. Ensure all connections are secure.

Note: Ensure correct handling of wires and connections as indicated by the diagrams to avoid damage or incorrect installation.

Step 2: Electrical Connection

Connect the light fixture to a 230 Volt / 50Hz power supply.

Procedure:

1. Identify Wires: Identify the live (L) and neutral (N) wires from your mains supply.
2. Connect to Terminal Block: Open the screw terminals on the light fixture's internal connector. Insert the neutral wire into the terminal marked 'N' and the live wire into the terminal marked 'L'.
3. Secure Connections: Tighten the screws on the terminal block firmly to ensure a secure electrical connection.
4. Finalize Mounting: Ensure the ceiling plate is securely attached to the ceiling, and the light fixture's wiring is properly connected and enclosed.

Refer to diagrams for precise wire insertion and terminal identification.

Step 3: Remote Control Setup

This section explains how to pair the included radio remote control with the light fixture. For detailed instructions, please refer to the separate Q-remote control manual.

Pairing Procedure:

1. Activate Pairing Mode: Switch the lamp on and off rapidly a specific number of times (typically 5 times, as shown in the reset section, but pairing might have its own sequence). The light should indicate it's ready for pairing.
2. Teach Remote Control: Point the remote control towards the Q-receiver (antenna) located on the fixture. Press and hold the designated pairing button on the remote control until the light confirms successful pairing (e.g., by flashing).

The Q-receiver is integrated into the top part of the light fixture.

Reset Procedure

To reset the lamp to its factory default settings, follow these steps:

Factory Reset:

1. Turn the lamp OFF using the wall switch.
2. Wait for 5-10 seconds.
3. Turn the lamp ON.
4. Wait for 1-2 seconds.
5. Turn the lamp OFF.
6. Wait for 1-2 seconds.
7. Turn the lamp ON.
8. Wait for 1-2 seconds.
9. Turn the lamp OFF.
10. Wait for 1-2 seconds.
11. Turn the lamp ON.
12. Wait for 1-2 seconds.
13. Turn the lamp OFF.
14. Wait for 1-2 seconds.
15. Turn the lamp ON.

The lamp should now be reset to its factory settings.

Declaration of Conformity and Contact Information

This device fulfills the fundamental requirements of Directive 2014/53/EU (Radio Equipment Directive) of the European Parliament and of the Council of the European Union dated 16.04.2014 on items of radio equipment.

The full declaration of conformity can be accessed at the following internet address:

https://scm.paul-neuhaus.de/public/conformity/

Manufacturer:

Paul Neuhaus GmbH
Olakenweg 36
D-59457 Werl
Germany

Contact:

Telefon: +49(0)2922-9721-0
Telefax: +49(0)2922-9721-9120
E-Mail: kundenservice@neuhaus-group.de