SuperFish PondECO User Manual

General Instructions

Read this manual carefully before using this device. Keep this manual for future reference.

Meaning of Symbols

The following warning symbols and/or signal words are used in this manual:

• ⚠️ DANGER! This means an imminent danger due to electric current. Failure to follow the safety instructions can result in serious or fatal injury and/or serious damage to the product or environment.
• ⚠️ WARNING! This means a dangerous situation. Failure to follow the safety instructions can result in moderate or minor personal injury and/or damage to the product or environment.
• ℹ️ NOTICE! This means caution, useful information or advice.
• Fig. ... This refers to the relevant drawing on pages 2 and 3 of this manual.

Meaning of the symbols on the device itself:

• ? 2m: This device is suitable for outdoor use and can be used underwater up to a 2 metre depth.
• ? IP68: This device is waterproof.
• ✅ CE: This device complies with all applicable EU standards.
• ♻️: This device may not be disposed of with normal household waste but must be collected separately for recycling.

Use

Suitable for outdoor use, for pumping pond water within the pond and inline set-up.

• The temperature of the pond water being pumped should not exceed 35°C.
• Do not use for pumping salt water, sewage water, flammable, corrosive and/or explosive liquids (e.g. petroleum, petrol, solvents), fats, oils or foodstuffs.
• Never run the device without water.
• Do not use for swimming pools and do not connect to drinking water supplies.

Safety

Always follow the safety instructions below for safe use of the device. Failure to follow these instructions may endanger persons or the environment.

• This device must be supplied through a residual current device (RCD) having a rated residual operating current not exceeding 30 mA. ⚡ [RCD protection]
• Ensure the voltage shown on the label matches the mains supply voltage.
• This device must be connected to a socket which is earthed. ? [Earthed socket]
• Protect the socket and plug against moisture. Use a drip loop to ensure water cannot reach the socket via the cord (see Fig. A). ? [Drip loop]
• Do not use the product if the device, cord or plug is damaged. Return the device to your dealer for repair or recycling. A damaged cord or plug cannot be replaced, the device should be recycled. ❌ [Damaged parts]
• Be careful with the combination of water and electricity. Do not operate with wet hands. Dry hands before carrying out maintenance. ⚠️ [Water & Electricity Hazard]
• Never use the device when there are people in the water. ?? [No people in water]
• Always switch off all devices at the mains supply before maintenance. ?➡️ OFF [Switch off power]
• Do not move or lift the device out of the water by the cord, only lift the device by the handle. ✋ [Lift by handle]
• This device can be used by children aged from 8 years and above, persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, if they have been given supervision or instructions concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and maintenance of the device shall not be done by children without supervision. ?? [Children's use]
• Modifications to the device may affect the safety. The warranty will also expire.

Function

The PondECO is an electronic pond pump for use with filters, skimmers, waterfalls and water ornaments.

Run Dry Protection

The pump is equipped with a dry-running safety device. If there is no water flow for 10 seconds, the pump will automatically stop and then restart after 10 seconds. If there is still no water flow, the pump will stop and restart again. This cycle is repeated 5 times, after which the pump stops completely. You can restart the pump when the water supply is restored by pulling the plug out of the socket, waiting 60 seconds, and plugging it back in.

Thermal Overload Protection

The pump has a thermal overload protection. In case the motor overheats, the pump switches off automatically. After a cooling down time of 15 to 20 minutes, the pump automatically switches on again. To prevent damage, investigate and resolve the cause of overheating. Damage caused by overheating is not covered by the warranty.

Installation

Pond Installation

Fig. B The PondECO pump is suitable for pond hoses with diameters of 25, 32 and 40 mm or 40 and 50 mm. Cut the Multi-step hose connector to the desired diameter and fasten it on the pump. Connect the pond hose to the hose connector using a hose clamp (not included). ? [Hose connection]

Fig. C Preferably install the pump in the deepest part of the pond (max. 2 metre depth), or at least 20 cm below the water surface. Make sure that the pump stands horizontally and firmly on a flat surface so that it cannot fall over. ⬇️ 2m [Max depth], ⚖️ [Stable placement]

Fig. A Plug the pump into the socket and make sure there is a drip loop in the cord. Make sure that no one can trip over the cord and that the cord cannot be damaged.

Inline Installation

Fig. D For inline use, remove the pre-filter cover from the pump and screw the supplied multi-step hose connections onto the pump.

Fig. E Remove the pre-filter cover by pressing the cover on both sides at the latches (1) and pulling it off (2).

Fig. B Cut the hose connectors to the desired diameter and then fasten them to the pump. The inlet is at the front of the pump, and the outlet is at the top. Connect the pond hoses to the hose connectors using hose clamps (not included).

Install the pump horizontally and firmly on a flat surface outside the pond. Make sure that the pump cannot tip over; if necessary, you can secure the pump with screws.

Fig. A Plug the pump into the socket and make sure there is a drip loop in the cord. Make sure that no one can trip over the cord and that the cord cannot be damaged.

Maintenance

• The pump should be cleaned regularly (minimum twice a year) to ensure trouble-free operation. Scale deposits, in particular, can cause your pump to cease. There is no warranty on failures due to dirty pumps and scale build-up inside the pump caused by improper or lack of maintenance. ?️ Twice a year.
• ⚠️ Remove the plug from the socket before carrying out maintenance!
• Disconnect the pump from the pond hose and rinse the housing under the tap or garden hose.
• For proper cleaning and descaling, it is best to use SuperFish Pump & UVC Clean (Art. 07070500), available from your dealer.
• Mix SuperFish Pump & UVC Clean in a large bucket with clean tap water according to the instructions on the bottle. Immerse the pump and leave it for 24 hours.
• Take the pump out of the bucket and let it drain before disassembling it.
• Fig. E Remove the pre-filter cover (if present) by pressing the cover on both sides at the latches (1) and pulling it off (2). Unscrew the Multi-step hose connection(s) from the pump.
• Fig. F Press the latch at the bottom of the pump (3) and slide the pump off the base (4).
• Fig. G Remove the rotor housing from the pump by turning it out of the lock (5), thereby releasing it (6). Now you can pull the rotor out of the pump.
• Brush and clean all parts and the housing thoroughly. Rinse everything with clean tap water and reassemble.
• Depending on usage, the rotor and rotor housing can get worn out and damaged; this is normal. A new rotor and rotor housing are separately available from your dealer.
• ❄️ NOTICE! During periods of frost, you should remove the pump from the pond. Clean and dry the pump well and store it frost-free.

Recycling

♻️ This symbol indicates that this product (if discarded) may not be disposed of with normal household waste. Instead, it must be handed in at an official collection centre (e.g. HWRC), or returned to the dealer when purchasing a similar new product. Follow the applicable rules in your country for the separate collection of electrical and electronic products. Separate collection and recycling are better for the environment, public health, and reduce waste.

Warranty

2 years manufacturer's warranty on materials and construction defects. Devices must be returned complete with all components, accompanied by an official proof of purchase confirming the purchase date for any warranty claims. Incomplete devices or devices without proof of purchase are not eligible for warranty. After receiving and checking, SuperFish will determine whether the device will be repaired or replaced. For a device repaired or replaced under warranty, the remaining time of the original warranty period applies. Carefully read the instructions on installation, use, and maintenance. Damage due to incorrect use, contamination, lack of cleaning, wear and damage to the rotor, or damage to the cord are not covered by the warranty.

Always keep the proof of purchase; without it, the warranty will be void!

Technical Specifications

Spare parts (Art. No.)

Diagram Description: The manual includes diagrams illustrating electrical connections (Fig. A), hose connectors (Fig. B), pond installation (Fig. C), inline installation (Fig. D), and pump disassembly steps (Fig. E, F, G). An exploded view of the pump components is also provided.