Introduction
This document provides step-by-step instructions for assembling your IKEA PAX wardrobe. Please read through all instructions before beginning assembly. Ensure you have all parts and tools listed.
Tools Required:
- ? Phillips head screwdriver
- ? Flathead screwdriver
- ? Hammer
- ? Spirit level
- ड्रिल Drill with 5 mm (1/4") drill bit
⚠️ For safety, it is recommended that two people assemble this product.
Parts List
- Dowel (101375): 34x
- Cam Lock Screw (118331): 30x
- Cam Lock Nut (100751): 2x
- Shelf Support (113434): 24x
- Hanging Rail Bracket (195701): 1x
- Screw (130718): 2x
- Screw (100402): 4x
- Screw (100644): 4x
- Connector (10093081): 16x
- Connector (10093082): 16x
- Base Connector (110617): 1x
- Base Connector (110618): 2x
- Base Connector (110519): 2x
- Foot (122972 / 115345): 4x
- Back Panel Connector (119030 / 120076): 6x
Assembly Steps
Step 1
Lay out the main panels. Insert 24x dowels (101375) into the pre-drilled holes on the edges of the panels as shown.
Visual: Panels laid flat, hands inserting dowels into holes.
Step 2
Attach the side panels to the base panel. Insert 24x cam lock screws (118331) into the designated holes on the side panels. Align these with the corresponding holes on the base panel and tighten.
Visual: Side panels being attached to a base panel, with screws being inserted and tightened.
Step 3
Continue attaching side panels. Insert 6x cam lock screws (118331) into the designated holes on the side panels and attach them to the base panel.
Visual: Similar to Step 2, showing more side panels being attached.
Step 4
Attach the top panel. Insert 1x cam lock screw (118331) into the top panel and secure it to the side panels.
Visual: Top panel being placed and secured with screws.
Step 5
Attach the remaining side panels. Insert 2x cam lock screws (118331) into the side panels and secure them to the base structure.
Visual: More side panels being added to the structure.
Step 6
Attach the hanging rail bracket. Insert 2x screws (130718) through the bracket (195701) and into the side panel.
Visual: A metal bracket being screwed into a side panel.
Step 7
Attach more vertical panels. Insert panels into the structure, aligning them with pre-drilled holes.
Visual: Vertical panels being slotted into place.
Step 8
Attach another vertical panel. Insert the panel into the structure.
Visual: Another vertical panel being added.
Step 9
Secure the structure with cam lock nuts. Insert 2x cam lock nuts (100751) into the designated holes and turn them to lock the panels in place. Use a hammer to gently tap them in if needed.
Visual: Cam lock nuts being inserted and tightened with a hammer.
Step 10
Attach the base connectors. Insert 2x base connectors (110618) and 1x base connector (110617) into the base of the wardrobe. Use a hammer to tap the screw part (110618) into the base connector (110617) with a 'click'. Then screw them into the base panel.
Visual: Base connectors being assembled and attached to the bottom of the wardrobe.
Step 11
Attach more vertical panels. Insert panels into the structure, aligning them with pre-drilled holes.
Visual: Vertical panels being slotted into place.
Step 12
Insert 6x dowels (101375) into the pre-drilled holes on the edges of the shelf panels.
Visual: Dowels being inserted into shelf panels.
Step 13
Insert 4x dowels (101375) into the pre-drilled holes on the edges of the shelf panels.
Visual: Dowels being inserted into shelf panels.
Step 14
Attach the shelf panels. Align the dowels with the holes in the side panels and press firmly.
Visual: Shelf panels being attached to the wardrobe frame.
Step 15
Insert 24x shelf supports (113434) into the pre-drilled holes on the inside of the wardrobe panels at the desired shelf heights.
Visual: Shelf supports being inserted into the wardrobe interior.
Step 16
Attach more vertical panels. Insert panels into the structure, aligning them with pre-drilled holes. Secure with fasteners.
Visual: Vertical panels being added and secured.
Step 17
Attach the back panels. Slide the back panels into the grooves on the rear of the wardrobe frame.
Visual: Back panels being slid into place.
Step 18
Continue attaching the back panels. Ensure they are fully seated in the grooves.
Visual: More back panels being slid into place.
Step 19
Secure the back panels. Use the provided connectors and screws to fasten the back panels to the wardrobe frame.
Visual: Fasteners being used to secure back panels.
Step 20
Insert 12x shelf supports (113434) into the pre-drilled holes on the inside of the wardrobe panels at the desired shelf heights.
Visual: Shelf supports being inserted into the wardrobe interior.
Step 21
Attach the final back panel connectors. Insert 3x connectors (119030 / 120076) and secure them.
Visual: Back panel connectors being attached.
Step 22
Attach the feet. Insert 2x feet (110519) into the bottom of the wardrobe. Use a hammer to tap the screw part (110519) into the base connector with a 'click'. Then screw them into the base panel.
Visual: Feet being attached to the base of the wardrobe.
Step 23
Attach 16x connectors (10093081 and 10093082) to the base of the wardrobe as shown. These are used to secure the base structure.
Visual: Connectors being attached to the base.
Step 24
Carefully position the wardrobe upright. This step may require two people.
Visual: Two people carefully lifting and positioning the wardrobe.
Step 25
⚠️ It is crucial to secure the wardrobe to the wall to prevent tipping. Use appropriate wall-mounting hardware (not included) for your wall type. The diagram shows the general placement for wall attachment.
Visual: Diagram showing how to attach the wardrobe to a wall, with a warning symbol.
Step 26
Attach the remaining feet. Insert 2x feet (122972 / 115345) into the bottom of the wardrobe as shown.
Visual: Feet being attached to the wardrobe.
Step 27
Drill pilot holes for wall mounting. Use a 5 mm (1/4") drill bit to drill 4x holes in the wall at the marked positions, corresponding to the wardrobe's mounting points.
Visual: Drill being used to make holes in the wall.
Step 28
Final securing. Attach 4x fasteners (100644 and 100402) to secure the wardrobe to the wall through the pre-drilled holes.
Visual: Fasteners being used to attach the wardrobe to the wall.
