HOMCOM 801-327V81 Kitchen Island Assembly Instructions
This document provides step-by-step instructions for assembling the HOMCOM 801-327V81 Kitchen Island.
Important Notes
Important: Retain for future reference. Read carefully.
Hardware Usage Notes:
- Quickfit: Tighten until the shoulder is flush with the panel. Do not overtighten or undertighten.
- Cam Lock: Ensure the starting position is correct before inserting the connecting quickfit. The cam lock head should be centered when the two panels are joined. Insert the cam lock before the quickfit. Turn the cam lock clockwise to tighten.
- Hinge Adjustment: Hinges may need adjustment for door alignment. Vertical adjustment involves loosening a screw and moving the door up/down. Gap adjustment involves turning a screw clockwise or anti-clockwise. Lateral adjustment involves turning a screw clockwise or anti-clockwise.
- Screws: Do not confuse similar screws.
- Drawer Slides: Ensure drawer slides are leveled for smooth operation.
Parts List
The following parts are included in the package:
- Part 1: Top Panel (x1)
- Part 2: Drop Leaf Panel (x1)
- Part 3: Cabinet Side Panel (x2)
- Part 4: Cabinet Back Panel (x1)
- Part 5: Drawer Side Panel (x2)
- Part 6: Base Panel (x1)
- Part 7: Drawer Bottom Panel (x1)
- Part 8: Drawer Back Panel (x1)
- Part 9: Shelf Panel (x1)
- Part 10: Drawer Front Panel (x3)
- Part 11: Drawer Slide (Inner part) (x2)
- Part 12: Drawer Slide (Outer part) (x1)
- Part 13: Foot (x1)
- Part 14: Foot (x1)
- Part 15: Drawer Slide Rail (Outer part) (x2)
- Part 16: Drawer Slide Rail (Inner part) (x1)
- Part 17: Vertical Support (x1)
- Part 18: Vertical Support (x1)
- Part 19: Vertical Support (x1)
- Part 20: Drawer Slide Rail (Outer part) (x1)
- Part 21: Drawer Slide (Inner part) (x3)
- Part 22: Drawer Slide (Inner part) (x3)
- Part 23: Drawer Slide (Inner part) (x3)
- Part 24: Drawer Slide (Inner part) (x3)
- Part 25: Drawer Bottom Panel (x3)
- Part 26: Door Panel (x2)
Hardware List
The following hardware is included:
- A: Screws (M4*14) (x28 + 1 spare)
- B: Cam Locks (x28 + 1 spare)
- C: Cam Dowels (x18 + 1 spare)
- D: Screws (M4*14) (x24)
- E: Hinges (x4)
- F: Screws (x5)
- G: Screws (x5)
- H: Screws (M4*35) (x28 + 1 spare)
- I: Screws (M3*12) (x60 + 1 spare)
- K: Screws (x6)
- L: Screws (x4)
- M: Screws (M4*12) (x16 + 1 spare)
- N: Screws (x2)
- O: Screws (x2)
- P: Screws (x3)
- Q: Cam Dowels (x3)
- R: Screws (x3)
- S: Screws (x3)
Step 2: Attach Vertical Supports
Attach Part 18 to Part 17 using two (2) Screws A.
Diagram shows two panels, Part 17 and Part 18, being joined. Screws labeled 'A' are shown being inserted into pre-drilled holes on the edge of Part 17 and into the face of Part 18.
Step 3: Attach Vertical Support to Base
Attach Part 19 to Part 18 using one (1) Cam Lock B and two (2) Cam Dowels C.
Diagram shows Part 19 being connected to the top edge of Part 18. A Cam Lock 'B' is shown being inserted into a hole on Part 19, and Cam Dowels 'C' are shown being inserted into Part 18, aligning with holes in Part 19.
Step 4: Attach Vertical Support to Base
Attach Part 17 to Part 19 using one (1) Cam Lock B and two (2) Cam Dowels C.
Diagram shows Part 17 being connected to the top edge of Part 19. A Cam Lock 'B' is shown being inserted into a hole on Part 17, and Cam Dowels 'C' are shown being inserted into Part 19, aligning with holes in Part 17.
Step 5: Attach Back Panel
Attach Part 4 to the assembled structure using four (4) Screws H.
Diagram shows Part 4 (a thin back panel) being placed against the rear of the structure formed by Parts 17, 18, and 19. Screws 'H' are shown being driven through Part 4 into the edges of the vertical supports.
Step 6: Attach Cabinet Side Panel
Attach one of the Part 3 panels to the structure using three (3) Screws A.
Diagram shows one of the larger side panels (Part 3) being attached to the assembly. Screws 'A' are shown being inserted through pre-drilled holes on the edge of Part 3 into the corresponding holes on the vertical supports.
Step 7: Assemble Drawer Support Rails
Connect Part 15 and Part 16 using the provided hardware.
Diagram shows two identical components (Part 15) being joined by a longer component (Part 16), likely forming a drawer slide assembly.
Step 8: Attach Drawer Support Rails to Cabinet
Attach the assembly from Step 7 (Parts 15 and 16) to Part 3 using four (4) Screws H.
Diagram shows the assembled drawer support rails being attached to the inside face of the cabinet side panel (Part 3). Screws 'H' are shown being used.
Step 9: Attach Drawer Bottom Panel
Attach Part 7 to Part 4 using two (2) Screws B.
Diagram shows Part 7 (a drawer bottom panel) being attached to Part 4 (cabinet back panel). Screws 'B' are shown being inserted through Part 7 into Part 4.
Step 10: Attach Drawer Back Panel
Attach Part 8 to Part 7 using one (1) Screw B.
Diagram shows Part 8 (drawer back panel) being attached to the edge of Part 7 (drawer bottom panel). A screw 'B' is shown being inserted.
Step 11: Insert Drawer Front Panel
Slide Part 10 onto the assembly.
Diagram shows one of the drawer front panels (Part 10) being slid into place, likely into grooves or slots on the drawer side panels (which are not yet fully assembled in this step's diagram).
Step 12: Insert Drawer Front Panels
Slide Part 10 onto the assembly.
Diagram shows a second drawer front panel (Part 10) being slid into place.
Step 13: Insert Drawer Front Panels
Slide Part 10 onto the assembly.
Diagram shows a third drawer front panel (Part 10) being slid into place, completing the drawer box structure.
Step 14: Attach Second Cabinet Side Panel
Attach the second Part 3 panel to the structure using three (3) Screws B.
Diagram shows the second cabinet side panel (Part 3) being attached to the assembly, mirroring Step 6. Screws 'B' are shown being inserted.
Step 15: Attach Base Panel and Drawer Sides
Attach Part 6 (Base Panel) and Part 5 (Drawer Side Panels) to the structure using sixteen (16) Screws M, two (2) Screws N, and two (2) Screws O.
Diagram shows the base panel (Part 6) and drawer side panels (Part 5) being attached to the main cabinet frame. Screws M, N, and O are indicated.
Step 16: Attach Cabinet Frame Components
Attach Parts 3, 7, and 8 to Part 6 using six (6) Screws C and six (6) Screws H.
Diagram shows the main cabinet frame being assembled, connecting various panels (3, 7, 8) to the base (6) using screws C and H.
Step 17: Attach Drawer Slide Rails to Drawer Sides
Attach the drawer slide rails (Parts 15, 16, 20) to the drawer side panels (Part 5) using six (6) Screws I and three (3) Screws P.
Diagram shows drawer slide rails being attached to the interior of the drawer side panels (Part 5). Screws 'I' and 'P' are indicated.
Step 18: Attach Drawer Side Panels to Base
Attach the drawer side panels (Part 5) to the base assembly using two (2) Screws C and two (2) Screws H.
Diagram shows the drawer side panels (Part 5) being attached to the base assembly. Screws 'C' and 'H' are indicated.
Step 19: Attach Feet
Attach the feet (Parts 13 and 14) to the bottom of the cabinet using twelve (12) Screws K.
Diagram shows the feet (Parts 13 and 14) being attached to the underside of the cabinet. Screws 'K' are shown being used.
Step 20: Attach Cabinet to Feet Assembly
Attach the main cabinet structure to the feet assembly using twelve (12) Screws I.
Diagram shows the main cabinet structure being connected to the feet assembly. Screws 'I' are indicated.
Step 21: Attach Drawer Slide Hardware
Attach hardware K to Part 1 using twelve (12) Screws I.
Diagram shows hardware 'K' being attached to Part 1 (likely a component of the drawer slide mechanism) using screws 'I'.
Step 22: Attach Top Panel
Attach Part 2 (Top Panel) to the main structure using eight (8) Screws A.
Diagram shows the main tabletop (Part 2) being placed on top of the cabinet structure and secured with screws 'A'.
Step 23: Attach Drop Leaf Support
Attach Part J to Part 2 using the provided hardware.
Diagram shows a support piece 'J' being attached to the underside of the top panel (Part 2), likely for the drop leaf mechanism.
Step 24: Attach Cabinet Side Panels
Attach Part 5 to Part 3 using eight (8) Screws B and six (6) Screws C.
Diagram shows the cabinet side panels (Part 5) being attached to the main cabinet structure (Part 3). Screws 'B' and 'C' are indicated.
Step 25: Attach Shelf Panel
Attach Part 9 to the assembly using four (4) Screws L.
Diagram shows the shelf panel (Part 9) being inserted and secured within the cabinet structure. Screws 'L' are indicated.
Step 26: Prepare Door Panels
Attach hinges (Parts D and E) to the door panel (Part 26) using eight (8) Screws D, four (4) Screws E, two (2) Screws F, and two (2) Screws G.
Diagram shows a door panel (Part 26) with hinges (Parts D and E) being attached using various screws (D, E, F, G).
Step 27: Attach First Door
Attach the prepared door panel (Part 26) to the cabinet structure (Part 3).
Diagram shows the first door panel being attached to the cabinet frame, aligning the hinges with the cabinet side.
Step 28: Attach Second Door
Attach the second door panel (Part 26) to the cabinet structure (Part 3).
Diagram shows the second door panel being attached to the cabinet frame.
Step 29: Assemble Drawers
Assemble the drawers by attaching drawer sides (Parts 22, 23, 24) and drawer front (Part 21) to the drawer bottom (Part 25) using twelve (12) Screws A, twelve (12) Screws B, three (3) Screws F, three (3) Screws G, and twelve (12) Screws H.
Diagram shows the assembly of three drawer boxes. Drawer sides, front, and bottom panels are shown being joined with various screws.
Step 30: Attach Drawer Slides to Drawers
Attach the drawer slides (Parts 11, 12, 21, 22, 23, 24) to the assembled drawer boxes using twelve (12) Screws I, three (3) Screws R, and three (3) Screws S.
Diagram shows drawer slide components being attached to the sides of the assembled drawer boxes. Screws I, R, and S are indicated.
Step 31: Insert Drawers
Carefully push the assembled drawers into the cabinet, ensuring the slides are aligned.
Diagram shows the completed drawers being slid into their respective openings within the cabinet.
