Delta 3-in-1 Crib Assembly Instructions and Safety Guide
Important Safety Information
Assembly Required
Adult Assembly Required
Due to the presence of small parts during assembly, keep out of reach of children until assembly is complete.
General Warnings
- This product is not intended for institutional or commercial use.
- Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding under an infant.
- Failure to follow these warnings and the assembly instructions could result in serious injury or death. Do not use this crib if you cannot exactly follow the accompanying instructions.
- To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep, unless otherwise advised by your physician.
- Strangulation Hazard: Strings can cause strangulation! Do not place items with a string around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or attach strings to toys.
- Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of the body or clothing on loose fasteners.
- Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or drapes may strangle a child.
- Fall Hazard: When a child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large toys, and other objects that could serve as steps for climbing out. This crib has an adjustable mattress support. For the convenience of the parent when the baby is very small, the mattress support may be used in the highest position. Important: with the mattress support and mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches higher than the top surface of the mattress. If it is not, lower the mattress support and the mattress to the next highest position.
- Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm), whichever occurs first. The child should be placed in a youth or regular bed.
- Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. Do not use crib if any parts are missing, damaged or broken. Contact Delta Children's Products for replacement parts and instructional literature if needed. Do not substitute parts.
- Follow warnings on all products in a crib.
- If refinishing, use a non-toxic finish specified for children's products.
- Never use plastic shipping bags or other plastic film as mattress covers because they can cause suffocation.
- Infants can suffocate in gaps between crib sides and a mattress that is too small.
- Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that every component is properly and securely in place.
- To avoid head injury, do not allow any child to play underneath the crib.
- Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
- In Canada Only: Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed firmly against any side of the crib, it does not leave a gap of more than 3 cm between the mattress and any part of the sides of the crib. Do not use this crib for a child who can climb out of it or who is taller than 90 cm.
Mattress Requirements
CAUTION: ANY MATTRESS USED IN THIS CRIB SHALL BE AT LEAST 27 1/4 BY 51 5/8 IN. WITH A THICKNESS NOT EXCEEDING 6 IN.
Consumer Care Contact
Website: https://www.DeltaChildren.com
Delta Children's Products, 114 West 26th Street, New York, NY 10001, Tele. 212-645-9033
Style #: ________ Lot: ________ Date: ________
JPMA CERTIFIED: ✔ JPMA CERTIFIED. Conforms to ASTM F1169-10a Full Size Crib & F1821 Safety Standards.
When contacting Delta Consumer Care, please reference the above information. Ensure that the information above matches the label on the Crib End bottom rail.
To register your product for important safety alerts and updates, please visit https://www.DeltaChildren.com and click on Product Registration.
Document Revision: JULY 19, 2013, 24342, R0. ©2013 DELTA ENTERPRISE CORP.
TODDLER BED CONVERSION WARNINGS
Toddler Bed Entrapment Hazard
- Infants have died in toddler beds from entrapment. Openings in and between bed parts can entrap head and neck of a small child.
- NEVER use bed with children younger than 15 months.
- ALWAYS follow assembly instructions.
- The maximum user weight is 50lbs (22.7kg).
Strangulation Hazard
- NEVER place bed near windows where cords from blinds or drapes may strangle a child.
- NEVER suspend strings over a bed.
- NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords, around a child's neck. These items may catch on bed parts.
Entrapment Hazard
- CAUTION: To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in thickness. The mattress thickness must not exceed 6 in (150mm).
Notes on Assembly
- During the assembly process, whenever using screws or bolts, check each by placing the screw/bolt on the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape specified in the instructions.
- To assemble this unit, you may be required to place the unit on its side and face. It is strongly recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
Notes on Use
- Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture.
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child's activity when in the nursery.
Notes on Care and Maintenance
- Do not scratch or chip the finish.
- Inspect the product periodically; contact Delta Children's Products for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a damp, cold basement. These extremes can cause a loss of structural integrity.
- To preserve the luster of the high quality finish on your product, it is recommended to place a doily or felt pad under any items you place on the finish.
- Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
- Do not use abrasive chemicals.
- Do not spray cleaners directly onto furniture.
- Lift slightly when moving on carpeting to prevent leg breakage.
- Use of a vaporizer near furniture will cause wood to swell and finish to peel.
Parts Identification
Crib Components
- A. Left Crib End x 1 (Part # 24337)
- B. Right Crib End x 1 (Part # 24338)
- C. Crib Side x 2 (Part # 24339)
- D. Stabilizer Bar x 1 (Part # 24340)
- E. Mattress Support x 1 (Part # 24343)
- Note: Pouch attached to mattress support contains instructions and warnings. Keep in pouch after assembly.
Diagram Description:
Line drawings show the main wooden components of the crib: two crib ends (A, B), two crib sides (C), one stabilizer bar (D), and the mattress support (E). Labels indicate 'Left Inside Bottom Label', 'Product Label', and 'Right Inside Bottom Label' on the crib ends.
Hardware Kit
- F. M6 x 60 mm Bolt x 8 (Part # 5469)
- G. M6 x 18 mm Bolt x 4 (Part # 5763)
- H. M6x17mm Barrel Nut x 8 (Part # 5479)
- J. Φ4x30 mm Metal Pin x 2 (Part # 5493)
- M4 Allen Wrench Supplied (Part # 1177)
- Note: Hardware kit part numbers vary by color (e.g., #24341-986 for Color 100).
Diagram Description:
Line drawings illustrate the hardware: bolts of different lengths, barrel nuts, metal pins, and an M4 Allen wrench. A note indicates 'No drills necessary. Do not use power screwdriver.' and 'Flat Head Screwdriver (not supplied)' is required.
Crib Assembly
Step 1: Attaching Crib Sides to Ends
Parts and tools required: Left Crib End (A) x 1, Right Crib End (B) x 1, Crib Side (C) x 1, M6 x 60 mm Bolts (F) x 4, M6x17mm Barrel Nuts (H) x 4, M4 Allen Wrench.
Attach one Crib Side (Part C) to the Left Crib End (Part A) and the Right Crib End (Part B) using four M6x60 mm Bolts (Part F) and four M6x17 mm Barrel Nuts (Part H). Tighten with the M4 Allen Wrench. Use a Flat Head Screwdriver to hold the Barrel Nut in proper alignment.
Diagram Description:
Diagram shows one crib side being attached to the two crib ends. Arrows indicate where bolts (F) are inserted and barrel nuts (H) are used to secure them. The M4 Allen wrench is shown for tightening.
Step 2: Installing Mattress Support
Parts and tools required: Mattress Support (E) x 1, M6 x 18 mm Bolts (G) x 4, M4 Allen Wrench.
Attach the Mattress Support (Part E) in all corners using one M6x18 mm Bolt (Part G) in each corner. Tighten with the M4 Allen Wrench.
Important Notes:
The warnings printed on the pouch attached to the mattress support must face up. The springs must face up.
This crib has (3) adjustment positions. Use the highest only for newborns, move the mattress down as the child grows.
WARNING: Fall Hazard
When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads, large toys and other objects that could serve as steps for climbing out.
WARNINGS ON POUCH MUST FACE UP.
Diagram Description:
Diagram shows the mattress support (E) being placed inside the assembled crib frame. Arrows indicate the insertion of bolts (G) into the corners to secure the support. A magnified view shows the bolt and barrel nut connection.
Step 3: Attaching Remaining Crib Side
Parts and tools required: Crib Side (C) x 1, M6 x 60 mm Bolts (F) x 4, M6x17mm Barrel Nuts (H) x 4, M4 Allen Wrench, Flat Head Screwdriver.
Attach the second Crib Side (Part C) to the assembly from Step 2 using four M6x60mm Bolts (Part F) and four M6x17mm Barrel Nuts (Part H). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
Diagram Description:
Diagram shows the second crib side being attached to the partially assembled crib, mirroring the process in Step 1.
Step 4: Finalizing Crib Assembly
Store the assembly instruction booklet in the pouch attached to the mattress support. Store all parts and tools separately, in a safe place.
Diagram Description:
Diagram shows the completed crib assembly. An arrow points to the 'AI BAG' (Assembly Instruction Bag) which is depicted on the mattress support.
WARNING: SEE PAGE 2 FOR INFORMATION
Toddler Bed Conversion
Step 1: Removing a Crib Side
Parts and tools required: M4 Allen Wrench Supplied.
Remove the Crib Side installed in Step 3 of Section 1 crib assembly. Remove only one side.
Diagram Description:
Diagram shows the finished crib. Arrows labeled 'PULL GENTLY' indicate the removal of a crib side by loosening bolts (F) and removing barrel nuts (H) from the crib side (C).
Step 2: Attaching Stabilizer Bar
Parts and tools required: Stabilizer Bar (D) x 1, Metal Pins (J) x 2, M6 x 60 mm Bolts (F) x 2, M6x17mm Barrel Nuts (H) x 2, M4 Allen Wrench, Flat Head Screwdriver.
Attach the Stabilizer Bar (Part D) to the assembly from Section 2 Step 1 using two Φ4x30 mm Metal Pins (Part J), two M6x60mm Bolts (Part F), and two M6x17mm Barrel Nuts (Part H). Tighten with the M4 Allen Wrench. Use the Flat Head Screwdriver to hold the Barrel Nut in the proper alignment.
Diagram Description:
Diagram shows the stabilizer bar (D) being attached to the frame where the crib side was removed. Arrows indicate insertion of pins (J) and bolts (F) with barrel nuts (H). A magnified view shows the connection detail.
Step 3: Final Toddler Bed Configuration
WARNING: SEE PAGE 3 FOR TODDLER BED WARNINGS
The mattress support must be in the lowest position.
Store all hardware safely.
Read all warnings on page 3.
As shown, use as a day bed or love seat sofa.
Do Not use without conversion rail installed.
Stabilizer bar must be used when converted to a toddler bed.
Toddler Bed Guardrail Availability
A toddler bed guardrail is available for this crib. Please see your crib retailer, visit https://www.DeltaChildren.com or contact Delta Consumer Care for more information. This crib uses Delta Style # 0081 Guardrail.
Diagram Description:
Two diagrams show the converted furniture: one as a toddler bed with the stabilizer bar and one side removed, and another as a day bed or love seat sofa.
Consumer Care and Warranty
Consumer Care Contact Information
Consumer Care: https://www.DeltaChildren.com
Delta Children's Products, 114 West 26th Street, New York, NY 10001, Tele. 212-645-9033
Warranty Information
This Delta Crib is warranted to be free from defects for a period of 1 year from the date of purchase under normal use. This warranty extends only to the original retail purchaser and is valid only when supplied with proof of purchase, or if received as a gift, when the registration is on file with Delta.
Product Registration
To register your product for important safety alerts and updates to your product please visit https://www.DeltaChildren.com.
Customer Support
Please do not return this item to the store before contacting us about missing parts or with any questions.
To report a problem, please log on to https://www.DeltaChildren.com and click the Consumer Care Tab, or contact us by phone at (212) 645-9033.
In the event that you need to contact our customer service department please have the Style Number and Lot Number available. Use the space below to make note of those numbers. They can be found on the label on the Crib End bottom rail.
Record Your Product Details
STYLE No: 6922
Lot No. : ___________
Pack Date: ___________
Date of Purchase: ___________ (you should also keep your receipt)
COLOR: ___________
REV: ___________ FTY: ___________
