Westinghouse Indoor Lighting Fixture

Introduction

Congratulations on your Westinghouse purchase. This fixture is designed for many years of beauty and service. For questions or comments, please email: catalogroom@westinghouselighting.com.

NOTE: Carefully unpack the fixture and all parts. Ensure all components are present before discarding packing materials (refer to Figure 1).

Warranty Information

This Westinghouse Lighting Fixture is warranted against defects in material and workmanship for five years from the purchase date. This warranty replaces all other expressed or implied warranties.

The warranty does NOT cover:

• Acts of nature (e.g., lightning damage).
• Corrosion or discoloration of components.
• Damage from abuse, improper installation, electrical surges, or acts of third parties.
• Broken glass. (If received with broken glass, contact Westinghouse Lighting for free replacement.)
• Costs of removing and re-installing the fixture.

If the fixture fails due to a covered reason, return it with a copy of the original sales receipt, freight prepaid. Westinghouse Lighting will, at its option, repair, replace, or refund the purchase price.

Safety Warnings

WARNING: ELECTRICAL SHOCK CAN RESULT IN SERIOUS INJURY.

• Read and follow all instructions exactly. If instructions are unclear, do not proceed. Consult a qualified electrician.
• Proper wiring is essential for safe operation.
• When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines.
• If any fixture or wiring components are damaged, do not install. Return to place of purchase.

Wire Temperature Warning: For fixtures with 75°C or 90°C supply wire warnings (found on U.L. label and carton): Risk of fire. Dwellings built before 1985 may have 60°C supply wires. Consult a qualified electrician before installing.

Grounded Outlet Note: This fixture employs a grounded type receptacle and is not intended for connection to a two-wire ungrounded source.

For Portable Lamps Only: To reduce the risk of electrical shock, portable lamps have a polarized plug (one blade is wider). This plug fits a polarized outlet only one way. If it does not fit, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully inserted. Do not alter the plug.

Diagram: Fixture Components and Mounting

The diagram illustrates the components and mounting process. Key parts include:

• Face Plate (A)
• Mounting Plate (C)
• Outlet Box (J)
• Wall Anchors (E)
• Screws (K)
• Ground Wire
• Side Hole (I)
• Green Grounding Screw (H)
• Wire Connectors (G)
• Cap Nuts (B1)
• Holder (M)
• Retaining Ring (N)
• Glass Shade (L)
• Outlet Box Screws (P) (Not Supplied)

Other labeled points include: Outer Holes (O), Additional Support Holes (F).

Note: Line art may not exactly match the enclosed fixture, but installation instructions apply.

Mounting and Wiring Instructions

NOTE: Underwriters Laboratories (UL) does not require all fixtures to have ground wires; these fixtures meet all UL specifications.

1. Peel protective coating from face plate (A) (if applicable).
2. Position the flat side of the mounting plate (C) against the wall at the mounting location. Mark the outer holes (O) with a pencil. Ensure the mounting plate (C) is level for the fixture to hang straight.
3. Drill a 1/8 inch hole at each pencil mark and gently tap wall anchors (E) into the holes with a hammer. For added support, anchors and screws can also be mounted in additional support holes (F).
4. Thread outlet box wires through the center opening of the mounting plate (C).
5. Position the mounting plate (C) with outer holes (O) over the wall anchors (E). Secure with screws (K) or attach the mounting plate (C) to the outlet box (J) using outlet box screws (not included).
6. Identify the color coding of the fixture wires (refer to Figure 2).
7. To connect wires: Take the black fixture wire (Group A) and place it evenly against the black outlet box wire. Do not twist wires together.
8. Fit a wire connector (G) over the wires and twist until a firm connection is felt. If the connector easily comes off, reattach and check again.
9. Repeat steps 7 and 8 for the white fixture wires (Group B) and the outlet box wires.
10. Partially thread the green grounding screw (H) into the side hole (I) on the mounting plate (C).
11. Wrap the fixture's ground wire around the green grounding screw (H), leaving enough excess wire to connect it to the outlet box ground wire with a wire connector (if applicable).
12. Tuck all wires neatly inside the outlet box (J).

Fixture Assembly Instructions

Warning: This fixture is for indoor use only.

1. Replace the face plate (A) over the mounting plate (C) and secure it with retaining screws (B) or cap nuts (B1).
2. Place the glass shade(s) (L) into the holder(s) (M) and secure with the retaining ring(s) (N) or thumb screws (N1) (if applicable).
3. Install lamp(s). Do not exceed the recommended wattage.
4. Turn the power back on at the circuit box.

Wiring Connections (Figure 2)

This section details wire connections, with parallel instructions for English, French, and Spanish.

English Instructions:

GROUP A: Connect to BLACK HOUSE WIRE

• BLACK
• WHITE OR GREY WITH TRACER
• BROWN, GOLD OR BLACK WITH TRACER

GROUP B: Connect to WHITE HOUSE WIRE

• WHITE
• WHITE OR GREY WITHOUT TRACER
• BROWN, GOLD OR BLACK WITHOUT TRACER

NOTE: When parallel wire (SPT I & SPT II) is used, the neutral wire is square shaped and ridged, and the hot wire is round and smooth.

WARNING: Turn off electricity to the mounting site before beginning installation. Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

French Instructions (Summary):

GROUPE A: Connecter au FIL NOIR DE LA RÉSIDENCE (Noir, Blanc ou Gris avec traceur, Brun/Doré/Noir avec traceur)

GROUPE B: Connecter au FIL BLANC DE LA RÉSIDENCE (Blanc, Blanc ou Gris sans traceur, Brun/Doré/Noir sans traceur)

NOTA: Fils parallèles (SPT I et SPT II): fil neutre carré/côtelé, fil chargé rond/lisse.

MISE EN GARDE: Coupez le courant avant l'installation. Suivez les instructions de montage pour une installation sécuritaire.

Spanish Instructions (Summary):

GRUPO A: Conéctelo al CABLE NEGRO DE LA CASA (Negro, Blanco o Gris con marcas, Marrón/Dorado/Negro con marcas)

GRUPO B: Conéctelo al CABLE BLANCO DE LA CASA (Blanco, Blanco o Gris sin marcas, Marrón/Dorado/Negro sin marcas)

NOTA: Cable en paralelo (SPT 1 y SPT 2): cable neutro cuadrado/acanalado, cable vivo redondo/liso.

ADVERTENCIA: Desconecte el suministro eléctrico antes de la instalación. Siga las instrucciones de montaje para un soporte seguro.

Cleaning and Care

To clean, wipe the fixture with a soft cloth. Clean glass with mild soap. Avoid chemical cleaners as they can discolor the finish.

Extend-A-Finish Lacquer Conditioner (Item #70295) is recommended annually for cleaning, conditioning, and protecting the fixture.

Do not use scouring pads, powders, steel wool, or abrasive paper.

For Solid Brass Fixtures: The durable acrylic lacquer coating provides weather protection. Over time, brass may develop an authentic antique finish. To maintain a bright finish, apply a good quality, non-abrasive car wax to all metal surfaces annually.

Ordering Parts

Keep this manual for future reference and for ordering replacement parts. Available parts can be ordered from the place of purchase. Use the exact wording from the diagrams when ordering.

Contact Information

Westinghouse Lighting Corporation

Philadelphia, PA 19154-1029, U.S.A.

Westinghouse Lighting Corporation, a Westinghouse Electric Corporation licensee

Website: www.westinghouselighting.com

"Westinghouse" and "You can be sure...if it's Westinghouse" are registered trademarks of Westinghouse Electric Corporation.

© 2010 WESTINGHOUSE LIGHTING CORPORATION