Westinghouse LED Indoor Lighting Fixture: Owner's Manual & Installation Guide

Welcome & Warranty Information

Congratulations on your Westinghouse purchase. This fixture has been designed to give you many years of beauty and service.

Fixture Warranty: This fixture is warranted against defects in material and workmanship for a period of five years from the purchase date. This warranty is in lieu of all other warranties expressed or implied. This warranty does not cover acts of nature such as lightning damage, or corrosion and discoloration of components, nor does it cover damages caused through abuse, improper installation, surges in electric current, or acts of third parties. This warranty does not cover the costs of removing and re-installing the lighting fixture.

For questions and comments, please visit www.westinghouselighting.com/contact-us.

Dimmable Switch Compatibility

Note: This fixture is suitable for use with dimmable switches. See below for a list of compatible dimmers.

Not recommended for use with motion sensors, light sensors, timers, or any other external controls.

Assembly Instructions

Note: Carefully unpack the fixture and parts. Make sure all parts are included before discarding any packing materials.

Diagram Description (Figure 1): Figure 1 illustrates the components and assembly process. Key parts include: Mounting Bar (C), Outlet Box (D), Outlet Box Screws (E), Mounting Nipple (B), Hex Nut (N), Lock Washer 1 (O1), Wire Connectors (F), Green Grounding Screw (G), Canopy (I), Lock Washer 2 (O2), Cap Nut (A), Thumb Screws (J), Glass Shade (K), and Shade Lip (L). A ground wire is also shown.

1. Raise the canopy (I) to the ceiling, allowing the mounting nipple (B) to protrude through the opening in the canopy (I).
2. Secure the canopy (I) in place with lock washer 2 (O2) (if applicable) and cap nut (A).
3. Unscrew the thumb screws (J) enough to insert the glass shade (K) (with the clear glass pointed downward).
4. Carefully support the glass shade (K) while securing the thumb screws (J). The shade (K) is secure when the thumb screws (J) fit snugly under the shade lip (L).

Mounting and Wiring Instructions

Note: Underwriters Laboratories (UL) does not require all fixtures to have ground wires. These fixtures meet all UL specifications.

Diagram Description (Figure 2): Figure 2 shows the wiring connections. Fixture wires (Black, White, Bare Copper/Ground) connect to House Wires (Black/Hot, White/Neutral, Bare Copper/Ground) using Wire Connectors (F).

1. Turn off power at the circuit box to avoid possible electric shock.
2. Remove cap nut (A) from mounting nipple (B). Thread hex nut (N) onto mounting nipple (B) approximately 1/4 inch and insert lock washer 1 (O1), then thread mounting nipple (B) into mounting bar (C) and secure with hex nut (N).
3. Secure mounting bar (C) to outlet box (D) using outlet box screws (E) (if applicable).
4. Identify color coding of fixture wires (refer to Figure 2).
5. Connect the black wire from the fixture with the black wire (hot wire) from the outlet box by wire connector (F), and wrap the wire connector (F) with electrical tape for a more secure connection.
6. Connect the white wire from the fixture with the white wire (neutral wire) from the outlet box by wire connector (F), and wrap the wire connector (F) with electrical tape for a more secure connection.
7. Partially thread green grounding screw (G) into side hole (H) on mounting bar (C).
8. Wrap grounding wire from fixture around green grounding screw stem (G) leaving enough excess wire, then connect the excess grounding wire from the fixture with the grounding wire from outlet box by wire connector (F) (if applicable), then wrap the wire connector (F) with electrical tape for a more secure connection.
9. Tighten green grounding screw (G). Do not over tighten.
10. Tuck wires inside outlet box (D).

After wiring: Turn power back on at the circuit box.

Warning: Turn off electricity to the mounting site before beginning installation. Mounting instructions must be followed exactly as shown for the fixture to be safely supported.

Cleaning and Care

To clean, wipe fixture with a soft cloth. Clean glass with mild soap. Sprays from chemical cleaners can discolor the finish of the fixture. Do not use scouring pads, powders, steel wool, or abrasive paper to clean this fixture.

Ordering Parts

Keep this manual for future reference, and in case replacement parts are needed. Available parts can be ordered from the place of purchase. Use exact wording from diagrams when ordering parts.

Important Safety Warnings

Warning: Electrical shock can result in serious injury.

Read and follow instructions exactly as shown. If instructions are unclear, do not proceed. Contact a qualified electrician. Read all instructions before beginning. Proper wiring is essential for safe operation of this fixture. When cutting or drilling into walls or ceilings, do not damage electrical wiring, gas lines, or water lines. If any of the fixture or wiring components are damaged, do not install fixture. Return to place of purchase.

Note for fixtures with 75°C or 90°C supply wire warning: (These warnings are provided on the U.L. label and on the fixture carton.) Risk of fire. Most dwellings built before 1985 have supply wires rated 60°C. Consult a qualified electrician before installing.