nVent Floor Standing Enclosure Mounting Instructions

Enclosure Overview

The basic components of the enclosure system are depicted, including a Rear Panel, Side panel, Roof plate, Mounting plate, Door, and Bottom plate.

Model Series Reference

The manual references several enclosure models and their associated part identifiers:

• MCS 6/7/8 (Ref. 1)
• MCD 9 (Ref. 2)
• MKS 10 (Ref. 3)
• MKD 12 (Ref. 4)
• T30
• SW10
• SW13
• SW19
• SW3
• T25
• CCM
• CCE
• CCI
• DHN 180
• CNM
• MPF
• LE 9304
• LC 02

Safety Warnings

WARNING: When mounting on or over a combustible surface, a floor plate of at least 1.43 mm galvanized or 1.6 mm uncoated steel extended at least 150 mm beyond the equipment on all sides must be installed.

WARNING: In order to maintain the environmental integrity of the enclosure, devices with the same environmental ratings shall be used to close openings in customized enclosures.

Combinable Enclosure Mounting (T30 Series)

Instructions for mounting combinable enclosures, detailing dimensions and steps.

Dimensions

Enclosure heights range from 1100 mm to 2200 mm with corresponding depths from 175 mm to 725 mm. A typical width dimension (A) is 525 mm.

Mounting Steps

The process involves attaching various plates and components using specified hardware (e.g., M5x10 screws, M6 screws) and torque settings.

Compact Enclosure Mounting (T30 Series)

Instructions for mounting compact enclosures, including IP rating considerations.

IP Ratings

The enclosure system supports specific IP ratings.

Mounting Steps

Steps involve securing components using screws and ensuring proper sealing.

Mounting Lift Handle

Instructions for mounting lift handles, typically using M5 screws with a torque of 4-5.5 Nm.

Locking Systems

Standard Locking System

Details steps for installing the standard locking mechanism, involving rotating components.

Lift Handle Locking System

Details steps for installing the lift handle locking mechanism, involving rotating components.

Back Panel Mounting

MCS Back Panel

Mounting the back panel for MCS enclosures. This involves using screws like M5x10 and M6x12, with specific quantities depending on enclosure width (W).

MKS Back Panel

Mounting the back panel for MKS enclosures, using screws like M5x10 and M6x12, with quantities varying by width (W).

MKD Back Panels

Mounting back panels for MKD enclosures, using M5x10 and M6x12 screws, with specific torque requirements (4-5 Nm).

Bottom Plate Mounting

Mounting Bottom Plates

Instructions for mounting bottom plates, using hardware such as St. 5.5x10 and M5x10 screws. Some steps are specific to 1200mm wide enclosures.

Sealing Bottom Plates

Instructions for sealing bottom plates, requiring M8x16 screws and specific placement for bottom left, bottom right, top left, and top right positions. Load capacity considerations (F > 1000N, F < 1000N) are noted.

Mounting Plate Installation

Standard Mounting Plate

Instructions for installing mounting plates, using M8x16 screws and specific placement for bottom right, bottom left, top right, and top left. Torque specifications are provided.

Mounting Plate 1600 Wide

Specific instructions for mounting plates on 1600mm wide enclosures, using M8x16 and M8x40 screws, with detailed placement and torque requirements.

MPD02 Mounting/Unmounting

Instructions for mounting and unmounting the MPD02 component, using M5x10 screws and specific placement for bottom left and bottom right.

Side Panel Mounting - SPM

Instructions for side panel mounting, utilizing components like M6x12 and M6x16 screws. Notes indicate specific fixation points for depths of 900 mm and above.

Torque values of 8-9 Nm and 8-10 Nm are specified for different fixation points.

Retainer Mounting - SPM

Notes that retainers are delivered pre-assembled. For older frame designs (700-800 mm depth), additional steps are required.

CCE/CCI Mounting

Instructions for mounting CCE 06 and CCI 06 components, using M6x12 screws. Torque specifications are provided, along with guidance on gasket placement on the top frame.

SW19 / LE 9304 / LC 02 Mounting

Instructions for mounting components including SW19, LE 9304, and LC 02, using M12x25 and M12 screws. Torque values of 15-20 Nm are specified.

CCM 04 Mounting

Instructions for mounting CCM 04 brackets, using specified screws. It is mandatory to install all four brackets at the corners. Fixation holes can be used with cage nuts and screws for better stability.

MPF Mounting

Instructions for mounting the MPF component, using specified screws and indicating click-in mechanisms for attachment.

DHN 180 Mounting

Instructions for mounting the DHN 180 component, using M6x12 screws with a specified torque of 8-10 Nm.

Door Adjustment

DHN 180 Door Adjustment

Steps are provided for adjusting the DHN 180 door, involving specific alignment and manipulation.

SW13 Door Adjustment

Instructions for adjusting the SW13 door, requiring specific torque settings of 13 Nm and 8 Nm at different points for precise alignment.

CNM Mounting

Instructions for mounting the CNM component, involving centering a plastic cage on a square hole and using rotate/push actions for installation.

Load Ratings and Components

Various load ratings are associated with specific components:

• 6400N is associated with LE 9304.
• 10200N is associated with LE 9304.
• 27000N is associated with LC 02.
• CCM, CCE, CCI components are also listed with load capacities.
• DIN 580 is also mentioned in relation to load capacities.

MCM / Mousepad Conversion

Instructions are provided for converting a Right Hand (RH) configuration to a Left Hand (LH) configuration for the MCM component, involving a series of steps with numbered parts.