Important Information Regarding Wall Materials and Fasteners
Wall materials vary significantly, therefore, screws and fasteners for wall mounting are not included with this product. For advice on suitable screw systems for your specific wall material, it is recommended to contact a local specialized dealer or hardware store.
Battery Safety Information
WARNING: Keep batteries out of reach of children. Swallowing a battery can be fatal. If a battery is swallowed, seek immediate medical attention. Before disposing of batteries, always cover the terminals with plastic tape to prevent short circuits. Store these instructions for future reference.
Before You Begin Installation
Diagram showing required tools: a pencil, a spirit level, a Phillips head screwdriver, and a flathead screwdriver.
Diagram illustrating common installation issues: forcing parts together (crossed out), missing parts (question mark), and seeking assistance from IKEA if unsure.
If you are unsure about the installation process or encounter difficulties, it is advisable to contact IKEA for assistance.
Included Components
- 1x Remote Control: Small square remote with two buttons (models 10061327, 10061329, 10062654, 10062633).
- 1x USB Power Adapter: For charging or powering the blind's motor unit.
- 1x USB Cable: For connecting the power adapter to the motor unit.
- 2x Mounting Brackets: Part number 10081418.
- 1x Motor Unit: The internal mechanism for operating the blind.
- 1x Battery Pack: For the motor unit.
Diagram showing all included components: a remote control, a USB power adapter, a USB cable, two mounting brackets, a motor unit, and a battery pack.
Installation Steps
Step 1: Prepare the Blind
Diagram showing the pleated blind installed in a window frame. Inset diagrams show connecting the motor unit to the blind and plugging the USB power adapter into a wall outlet.
Ensure the motor unit is properly connected to the blind and, if necessary, plug in the USB power adapter.
Step 2: Attach Mounting Brackets to the Blind
Diagram showing the blind's top rail with two marked points 16 cm (6.3") from each end. Inset diagrams show attaching the mounting brackets (part 10081418) to the blind's top rail, with an audible 'Click!' indicating secure attachment. The main diagram shows the blind with brackets attached.
Position the two mounting brackets (part 10081418) on the top rail of the blind, approximately 16 cm (6.3 inches) from each end. Push them firmly until they click into place.
Step 3: Mark and Drill for Wall/Ceiling Mounting
Diagram showing the blind being installed into a window recess or on a wall. An arrow points to page 16, indicating continuation of installation steps.
Determine the desired mounting location (inside the window recess or on the wall/ceiling above the window). Use the attached brackets to mark the drilling points. Ensure the marks are level.
Step 4: Secure Mounting Brackets to Wall/Ceiling
Diagram showing how to attach the mounting brackets (part 10081418) to the wall or ceiling, with an audible 'Click!' indicating secure attachment. Another diagram shows screwing the brackets into the wall/ceiling (2x).
Drill holes at the marked points and secure the mounting brackets to the wall or ceiling using appropriate screws (not included). Ensure the brackets are firmly attached.
Step 5: Mount the Blind
Diagram showing the blind being pushed upwards into the mounted brackets until it clicks into place. Inset diagrams show the mechanism of the bracket locking the blind in place, with an audible 'Click!' indicating secure attachment.
Align the blind with the mounted brackets and push it upwards until it clicks securely into place. Ensure both sides are properly engaged.
Step 6: Release Mechanism (if needed)
Diagram showing the blind installed in a window recess. Inset diagram shows the mechanism for releasing the blind from the brackets using a tool.
If the blind needs to be removed, use a flat tool to press the release tab on each bracket while gently pulling the blind downwards.
Battery Installation and Replacement
For the Blind's Motor Unit
Diagram showing how to open the battery compartment of the blind's motor unit by sliding a cover. Another diagram shows inserting the battery pack into the motor unit. A third diagram shows the battery pack being inserted into the motor unit.
To install or replace the battery in the blind's motor unit, slide open the battery compartment cover. Insert the battery pack, ensuring correct orientation, then close the cover.
For the Remote Control
Diagram showing how to open the remote control to insert a CR2032 3V Lithium Battery. An audible 'Click!' indicates correct battery placement. A crossed-out battery symbol indicates proper disposal. Another diagram shows closing the remote control.
To install or replace the battery in the remote control, open its casing. Insert a CR2032 3V Lithium Battery, ensuring the positive (+) side is facing up. Close the casing until it clicks. Dispose of used batteries responsibly.
Remote Control Wall Mounting
Diagram showing different wall materials (wood, plasterboard, concrete) and a crossed-out screw, indicating screws are not included. Another diagram shows a wall mount for the remote control, with screws. An exclamation mark symbol with various wall types indicates the need for appropriate fasteners.
The remote control can be mounted on a wall. Choose appropriate screws for your wall material. The diagram illustrates various wall types and the importance of selecting suitable fasteners.
Operating the PRAKTLYSING Blind
Using the Remote Control
Diagram showing how to lower the blind using the remote control (models 10061327, 10061329, 10062654, 10062633). Another diagram shows how to raise the blind using the remote control.
To lower the blind, press the 'down' button on the remote control. To raise the blind, press the 'up' button on the remote control.
Manual Operation
Diagram showing how to manually lower the blind by pressing a button on the motor unit. Another diagram shows how to manually raise the blind by pressing a button on the motor unit.
The blind can also be operated manually by pressing the corresponding button on the motor unit to raise or lower it.
Smart Home Integration
Diagram showing the PRAKTLYSING blind, a TRÅDFRI gateway, and symbols for voice control, timer, and app download (Apple App Store, Google Play Store), indicating compatibility with IKEA Home smart.
The PRAKTLYSING blind is compatible with IKEA Home smart systems. It can be integrated with a TRÅDFRI gateway for advanced control, including voice commands, scheduling, and management via the IKEA Home smart app. The app is available for download on the Apple App Store and Google Play Store.
